Quick Start Guide
5.
Mounting Back Wall
Mounting
Back Wall
Securely align the mounting slots of access
point with hooks of the bracket
WARNING: HFCL is not held liable for any damages incurred during the process.
8
Getting the ion4xi_WP Online
Step 1: Power up
The Access Point can be powered up using PoE adaptor (48V)
or DC adaptor (12V) as shown below:
DC Power Adaptor
Power up using DC Power Adaptor
PoE Adapter (48V)
Cat-5
(Ethernet Cable)
Introduction
Align the mounting slots of the Access Point with the hooks
of the bracket and ensure that it is properly hinged in its place
6. Secure the Access Point to the bracket by tightening the Phillips
Security Screw using the Allen key.
Packaging Content
Step 2: Connect to the network
Section 1: Standalone AP
Follow the steps mentioned below and connect the Access Point
to a network
1. Connect an ethernet cable to the computer.
2. Connect the other end of the ethernet cable to the LAN port
on the Access Point or use a PoE adaptor to do so.
2
910 11 12 13
ion4xi_WP Specifications
Note: Plug and Adaptor will vary by country/ region
Power up using PoE Adaptor
Peak Throughput(aggregate) Up to 1.78 Gbps
Wi-Fi Standard Support 802.11 a/b/g/n/ac/ac Wave 2/ax
Ethernet support/
Ports/Interface
1 X 10/100/1000/2500 BASE-T Ethernet (WAN & PoE-In)
4 X 10/100/1000 BASE-T Ethernet (LAN)
DC input jack (optional)
Reset and WPS buttons
MU-MIMO 2x2:2
Mesh Support Self-creating, Self-healing EasyMesh
Maximum number of SSID
(per radio)
16
Maximum User Support 256
Power Supply IEEE 802.3af PoE or +12V DC Power Adaptor (optional)
Power Consumption (Max) 15 W (approx.)
Max Transmit Power 2.4 GHz- up to 20 dBm & 5 GHz- up to 23 dBm
(will depend on country specific guidelines)
Antenna Type Integrated antennas
Antenna Gain 4 dBi for both 2.4 GHz and 5 GHz
Management Standalone (via GUI) or through
on-premise based solution or cloud-based
Enclosure Dimensions 163 x 150 x 38 mm (6.4 x 5.9 x 1.49 inch)
Weight 0.59 kg
Operating Temperature 00C to 400C
Certifications FCC Class B, CE, Passpoint 3.0, EasyMesh, WPA3, RoHS 3.0
Section 2: Controller Managed AP
Product Overview
Step 3: Check the LED status Safety Precautions
Observe the following safety precautions to avoid damage to
the Wall Plate Access Point
Do not subject the device to high temperatures
Keep away from high voltage cables
Disconnect the device before cleaning it
Do not wipe the device with a damp cloth
Do not open the enclosure of the Access Point
Fasten the device tightly with the mount
Kensington Lock
Reset Button
WPS
Part Number: QSG-01-0025
Revision: A
Contact Us:
Website: www.hfcl.com | www.io.hfcl.com
Address: 8, Commercial Complex, Masjid Moth,
Greater Kailash-II, New Delhi- 110048
by HFCL
WAN+ PoE
(Power up the device by PoE Adaptor and
a regular Ethernet Port)
Mounting Slots
DC Jack
(Power up using 12V Adaptor)
Status and Power LED
4 LAN Ports
Mounting of ion4xi_WP Access Point
3.There are several mounting holes on the bracket that may be
used with various wall boxes. Attach the bracket on the wall
using the wall mount screws
Note: Make sure that mounting bracket is tightly installed before mounting the Access Point on the wall.
An electrical wall box should be pre-installed with an Ethernet
cable running from the box to a Switch with PoE
3. Open the web browser and enter the Access Point static IP
address in the address bar: 192.168.1.1
4. A login screen will appear.
5. Enter the default login credential details: User- root,
Password- hfcl!@ion
Follow the steps mentioned below and connect the Access
Point to a network :
1. Power-up the AP through PoE adapter or PoE switch
2. Connect the AP to DHCP network and Internet
3. Login to HFCL I0 cloud controller (cNMS) cnms.ionetworks.in
with credentials provided
4. Refer our website io.hfcl.com for detailed information to
configure AP through cNMS HFCL Limited All Rights Reserved. I0 Networks and the I0 logo are registered
trademarks of HFCL Limited. Specifications are subject to change without notice.
Status and Power LED
LED Color Status
Blue (Constant) Solid/constant blue color notifies the user that the
device is powered ON and no data is being transmitted
Blue (Slow blinking)
Slow blinking blue color notifies the user that the
device is powered ON and data is being transmitted on
either one or both radios
Blue (Fast blinking) Fast blinking blue color notifies the user that
the device is rebooting
Laptop/ Computer
PoE Adapter (48V)
Cat-5
(Ethernet Cable)
ion4xi_WP
Access Point
(Qty:1)
by HFCL ANYWHERE
EVERYWHERE
Mounting Bracket
(Qty:1)
Allen Key
(Qty:1)
Plastic Wall Anchors
(Qty:4)
Wall-Mount Screws
(Qty:4)
Phillips Security Screw
(Qty:1)
Phillips Screws
(Qty:4)
Mounting Bracket
1. The Access Point comes with a pre-attached wall
mounting bracket
2. Use Allen Key to unscrew the wall mounting bracket from
the Access Point
4. Pass the Ethernet cable through the bracket and connect it
to the PoE port on the Access Point
Holes in the mountain bracket
(To attach the bracket to the wall)
Mounting Hooks
WAN+ PoE
(Power up the device by PoE Adaptor and
a regular Ethernet Port)
Allen KeyMounting bracket
(Attached to the access point)
Mounting
Back Wall
ion4xi_WP
Wall Plate Access Point
Sleek yet Powerful
Thank you for choosing ion4xi_WP Wireless Access Point with
2x2:2 Multi-User MIMO and 802.11ax compliance. This Quick
Start Guide is designed to guide you through the installation
process the Wall Plate Access Point
1
iO 8i Access Point User guide
Ubiquiti UAP-PRO Quick start guide
Ubiquiti UAP-nanoHD Compact 802.11ac Wave 2 Enterprise Access Point User guide
Ubiquiti UAP-AC-PRO Quick start guide
Grandstream GWN7600 User manual
Funkwerk 5530000173 Datasheet
Cisco C886 Installation guide
Ubiquiti UniFi UAP-AC-IW Quick start guide