2. Computers & electronics
  3. TVs & monitors
  4. Wall & ceiling mounts accessories
  5. Aqua Creek
  6. F-035EZSM

Aqua Creek F-035EZSM Operating instructions

  • Hello! I'm your chat assistant, and I've read the user manual for the Aqua Creek Products EZ Surface Mount Anchor F-035EZSM. This document provides instructions on how to properly install the mount anchor, including drilling, anchoring and final mounting, and covers important safety guidelines and bonding requirements. I'm ready to answer your questions about installation, usage and safety precautions.
  • What should I do before beginning assembly?
    What should I do if any damage occurred in transit?
    What is the maximum setback distance for the anchor?
Copyright © 2016 Aqua Creek Products All Rights Reserved Revised 12/13/16
EZ Surface
Mount Anchor
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | +1-406-549-0769
www.aquacreek.com
PART #: F-035EZSM
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
supervision
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructionsandidentifypartsusingtheguresandpartslistedinthisdocument.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit,AquaCreekProducts,LLCmustbenotiedwithinthreedaysofreceiptofunit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warranty and may affect the safety of the user.
READ CAREFULLY
1
Copyright © 2016 Aqua Creek Products All Rights Reserved Revised 12/13/16
INSTALLATION INSTRUCTIONS:
1. Find the desired location for the lift. The setback (the distance from the center of the anchor to
the inside pool wall) can be no more than 20” as shown in FIGURE 2 on the next page.
2. Using the anchor as a template, drill four (4) 1 1/2” holes at the four bolt locations to a depth of
4 1/2”. Clean all debris from the hole.
3. Fill the holes 1/2 full with two part construction epoxy.
4. Set the 1” x 4” anchor inserts into the holes. Wiggle inserts to be sure the epoxy gets on all
sides. Make sure the anchors end up ush with the concrete’s surface.
5. Mount the SURFACE MOUNT ANCHOR to the deck using four (4) 1/2” x 1” hex bolts, and four (4)
1/2” at washers. Tighten the bolts until snug plus 1/2 turn.
Packing List & Installation Instructions
CONCRETE ANCHOR
SOCKET
QTY DESCRIPTION
1 SURFACE MOUNT ANCHOR, EZ
4 WASHER, FLAT, 1/2, 316 SS
4 BOLT, 316 SS, 1/2 X 1 1/2 HCS
4 ANCHOR INSERT, 1” x 4”
PACKING LIST:
1/2" X 1 1/2"
HEX BOLT (4)
1/2" FLAT
WASHER (4)
1" X 4" ANCHOR
INSERT (4)
EZ SURFACE
MOUNT ANCHOR
FIGURE 1
2
Copyright © 2016 Aqua Creek Products All Rights Reserved Revised 12/13/16
4"
6"
MIN.
POOL
WALL
8-AWG SOLID COPPER
WIRE ATTACHED TO
BONDING GRID
ANCHOR
INSERT
20" MAX
14"
14"13"
POOL
CHECK YOUR LOCAL ELECTRICAL CODES FOR: BONDING REQUIREMENTS FOR
POOL EQUIPMENT. ALWAYS BOND UNIT PER LOCAL ELECTRICAL CODES.
FIGURE 2
3
/