Learning Resources LER 2062 User manual

Brand
Learning Resources
Model
LER 2062
Category
Educational resources
Type
User manual

This manual is also suitable for

Build 2 Legs and Bottom Section:
1. Insert a Wheel (I) into each hole at the bottom of the
Wheel Connector (F). Turn the loose nut so that the
wheel is tightened.
2. Place Middle Bottom Poles (B) into the sides of the
Wheel Connector (F). Take the short screws (J) and place
them in the holes on the other side of the Middle
Bottom Poles. Tighten screws with wrench.
3. Put two of the Bottom Side Poles (A) into the top of the
left Wheel Connector (E). The holes in the poles should
be facing inward and towards the bottom of the rack.
Push the poles until they are all the way in.
4. Line one Drawer Holder (C) with the bottom holes on the
Bottom Side Poles (A). Make sure flat drawer runners are
facing downward. Use 2 of the long screws (K) to hold
that side of the Drawer Holder. Do not tighten.
5. Repeat Step 4 with the other Drawer Holder (C) with the
top holes of the Bottom Side Poles (A).
6. Put the remaining 2 Bottom Side Poles (A) into the top
of the right Wheel Connector (E). Push the poles until
they are all the way in.
7. Repeat Steps 4 and 5 with the right side. Tighten all long
screws (K).
8. Place the Shelf (D) on the top Drawer Holder (C) and
push down so it is sturdy.
Build Top Section:
9. Push the Side Connectors (G) onto the Bottom Side Poles
(A). The knobs of the Side Connectors should be facing
outward. Be sure the screws are all the way out.
10. Slide 4 Top Side Poles (D) into the Side Connectors (G).
Turn the knobs on the connectors to hold poles in place.
11. Attach L-Connectors (H) onto the Top Side Poles (E).
Locks on connectors should face upwards, towards the
outside, and open.
12. Slide Ring Hooks (R) on the middle Top Poles. Put five
hooks on each pole (E).
13. You may need to take one L-Connector and place the
pole in one end first. Fit remaining 2 Top Poles (E) in
between the L-Connectors. Be sure it fits tightly.
14. Push caps (P) onto Pull-out Poles (Q).
15. Insert Pull-Out Poles (Q) into Middle Top Poles (E)
and lock L-Connectors (H) into position.
16. Line the Drawer Knobs (N) with the holes on the Drawers
(L). Use the Knob Screws (M) to fasten the knobs.
17. Place the drawers in the Drawer Holders (C)
LER 2062
Double Pocket Chart Stand with Storage
Assembly Instructions
© Learning Resources, Inc., Vernon Hills, IL (U.S.A.)
Learning Resources Ltd., King’s Lynn, Norfolk (U.K.)
Please retain our address for future reference.
Made in Taiwan. LPK2062-GUD
Fabriqué en Taiwan. Informations à conserver.
Made in Taiwan. Bitte bewahren Sie unsere Adresse
für spätere Nachfragen auf.
Hecho en Taiwán. Conservar estos datos.
For a dealer near you, call:
(847) 573-8400 (U.S. & Int’l)
(800) 222-3909 (U.S. & Canada)
+44 (0)1553 762276 (U.K. & Europe)
P
H
Q
R
G
A
L
D
C
B
N
I
F
E
RISQUE D’ÉTOUFFEMENT.
Petites pièces.
Interdit aux enfants en dessous de 3 ans.
ERSTICKUNGSGEFAHR.
Kleine Teile. Nicht geeignet
für Kinder unter 3 Jahren.
PELIGRO.
No conveniente para niños menores de 3 años por
ser susceptible de producir piezas pequeñas que pueden ser ingeridas.
Contents:
A. Bottom Side Pole (4)
B. Middle Bottom Pole (2)
C. Drawer Holder (2)
D. Shelf (1)
E. Top and Top Side Poles (6)
F. Wheel Connector (2)
G. Side Connector (2)
H. L-Connector (4)
I. Wheels with nuts (4)
J. Short Screws (4)
Contents:
K. Long Screws (8)
L. Drawers (4)
M. Small Screws for Knobs (4)
N. Drawer Knobs (4)
O. Allen Wrench (1)
P. Cap (4)
Q. Top Pull-Out Poles (2)
R. Ring Hooks (10)
Allen wrench (O) is provided to
tighten all screws.
  • Page 1 1

Learning Resources LER 2062 User manual

Brand
Learning Resources
Model
LER 2062
Category
Educational resources
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents