George Kovacs P1793-077 User manual

P1793-077
Brand
George Kovacs
Model
P1793-077
Type
User manual

This manual is also suitable for

George Kovacs P1793-077 is a stylish and versatile light fixture that can be used to enhance the ambiance of any room. With its adjustable rod and chain, it can be customized to fit your specific needs and preferences. The fixture's crystal bar adds a touch of elegance, while the included bulb provides ample illumination. Installation is simple and straightforward, making it a great choice for do-it-yourself enthusiasts.

George Kovacs P1793-077 is a stylish and versatile light fixture that can be used to enhance the ambiance of any room. With its adjustable rod and chain, it can be customized to fit your specific needs and preferences. The fixture's crystal bar adds a touch of elegance, while the included bulb provides ample illumination. Installation is simple and straightforward, making it a great choice for do-it-yourself enthusiasts.

ASSEMBLY THE FIXTURE (FIG. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the existing fixture and its mounting
hardware from the ceiling.
2. Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to lose any small parts necessary for
installation.
3. Determine the rod length if necessary, then assemble the rod
(C) together using nipple (E), then assemble the small rod (D)
onto the rod (C), after that, assemble the bottom end of the
rod (D) onto the coupling (B) and assemble the small loop (F)
onto the top end of the rod (C).
4. Install the bulb (N) (not included) in accordance with the
fixture’s specifications. (DO NOT EXCEED THE MAXMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
5. Connect the small loop (F) and (I) using the chain quick link
(G) well.
6. Attach the cross bar (M) to the outlet box using the outlet box
screws (K). The side of the mounting bar marked “GND” must
face out.
7. Follow the wiring instructions carefully (See Fig.2).
8. Attach the fixture main body onto outlet box by protruding
mounting screws (L) through mounting holes on the canopy
and secure with ball nut (J).
9. Assemble the crystal bar (A) onto nipple (O) well.
CONNECTING THE WIRES (FIG. 2)
10. Connect the electrical wires as follows. Connect the smooth
wire from the fixture to the smooth (HOT) house wire.
Connect the ribbed wire from the fixture to the ribbed (Neutral)
house wire. Make sure all the wire nuts were secured. You
may wrap the connections with electrical tape. If your outlet
box has a ground wire (Green or Bare Copper) connect
fixture’s ground wire to it. Other wise attach the bare copper
fixture wire to the green ground screw on the mounting bar.
11. Tuck the wire connections neatly into the ceiling junction box.
Your installation is now complete. Turn on the power supply of
the junction box to test the fixture.
Fig.1
K
M
L
J
I
G
F
C
E
B
A
O
H
N
D
INSTALLATION INSTRUCTION FOR FIXTURE #P1793, P1794
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Set A#A-010
-Crossbar
-Ground Screw
-Mounting screws (2)
12” ROD
W35-1-416
W35-1-077
  • Page 1 1

George Kovacs P1793-077 User manual

P1793-077
Brand
George Kovacs
Model
P1793-077
Type
User manual
This manual is also suitable for

George Kovacs P1793-077 is a stylish and versatile light fixture that can be used to enhance the ambiance of any room. With its adjustable rod and chain, it can be customized to fit your specific needs and preferences. The fixture's crystal bar adds a touch of elegance, while the included bulb provides ample illumination. Installation is simple and straightforward, making it a great choice for do-it-yourself enthusiasts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents