GE DPSE592EA0AA Installation guide

Brand: GE

Model: DPSE592EA0AA

Type: Installation guide

Installation

Instructions

ElectricDryer

Questions on Installation? Call: 1-8OO-GECARES (US)

or Visit our Web site at: www.GEAppliances.com (US)

BEFOREYOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT -Savethese

instructions for local inspector's use.

•IMPORTANT -Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with

the customer.

• Note to Customer - Keep these instructions with your Use

and Care Book for furore reference.

• Exhausting the dryer to the outdoors is strongly recom-

mended to prevent large amounts of moisture from being

blown into the room.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Service information and the wiring diagram are located in

the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance is

used near children.

FORYOUR SAFETY:

WARNING

• Use only rigid metal or flexible metal 4-in. diameter

ductwork for exhausting to tile outdoors. Never

use plastic or other combustible, easy-to-puncture ductwork.

• This appliance must be properly grounded and installed

as described in these instructions.

• Do not install or store appliance in an area where it

will be exposed to water and/or weather

• Install tile dryer where the temperature is above ,50°F

for satisfactory operation of the dryer control system.

NOTE: Installation and service of this dryer

requires basic mechanical and electrical skills.

It is your responsibility to contact a qualified

installer to make the electrical connections,

TOOLS YOU

WILL NEED

SLIPJOINTPLIERS

FLATBLADESCREWDRIVER

PHILLIPSSCREWDRIVER

MATERIALSYOU WILL NEED

4" DIA.METALDUCT

(RECOMMENDED) DUCT

CLAMPS(2)

4"SPRING

CLAMPS(2)

4"DIA.FLEXIBLEMETALDUCT

(IFNEEDED)

4"DIA.METAL

ELBOW

EXHAUSTHOOD SAFETYGLASSES

_ 3/4"_RELIEF

DUCTTAPE GLOVES ULRECOGNIZED

DRYERPOWER

CORDKIT

(NOTPROVIDED

WITHDRYER)

ULRATED120/240V,30A

WITH3OR4PRONGS.

IDENTIFYTHEPLUGTYPE

ASPERTHEHOUSE

RECEPTACLEBEFORE

PURCHASINGLINECORD.

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Prepare the Area and Exhaust for Installation of

New Dryer (see section 1).

Check and Ensure the Existing External Exhaust is

Clean (see section 1) and Meets Attached Installation

Specifications (see section 3).

Remove the Foam Shipping Pads (see section 1).

Move the Dryer to the Desired Location.

Connect the Power Supply (see section 2).

Connect the External Exhaust (see section 4).

Level Your Dryer (see section ,_).

Step 8

Step 9

Check the Operation of the Power Supply

and Venting.

Place the Owners Manual and the Installation

Instructions in a Location Where They Will Be

Noticed By tile Owner.

For Alcove or Closet Installation, see section 6.

For Bathroom or Bedroom Installation, see section 7.

For Mobile or Manufactured Home see, section 8.

For side or bottom exhaust, see section 9.

Installation Instructions

Minimum Clearance Other Than Alcove or Closet Installation

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear. Consideration

must be given to provide adequate clearance for installation and service.

[] PREPARING FOR INSTALLATION

OF NEW DRYER

EXTERNAL

DUCT

OPENING

DUCTTAPEOR

DUCTCLAMP

4"METALDUCT

DUCTTAPEOR

DUCTCLAMP

TIP: Install your dryer before installing your washer.

This will allow better access when installing dryer exhaust.

REMOVING LINT FROM WALL

EXHAUST OPENING

INTERNALDUCT

WALL

CHECKTHATEXHAUST

DAMPEROPENS

ANDCLOSESFREELY.

TILTTHEDRYERSIDEWAYS

ANDREMOVETHEFOAM

SHIPPINGPADSBY

PULLINGATTHESIDES

ANDBREAKINGTHEM

AWAYFROMTHEDRYER

LEGS.BESURETO

REMOVEALLOFTHE

FOAMPIECESAROUND

THELEGS,

[] ELECTRICAL CONNECTION

INFORMATION

WARNING- TO REDUCE THE RISK OF

FIRE, ELECTRICAL SHOCK AND PERSONAL

INJURY:

DO NOT USE AN EXTENSION CORD OR AN

ADAPTER PLUG WITH THIS APPLIANCE.

Dryer must be electrically grounded in accordance with

local codes and ordinances, or in the absence of local

codes, in accordance with the NATIONAL ELECTRI-

CAL CODE, ANSI/NFPA NO. 70.

ELECTRICAL REQUIREMENTS

This dryer must be connected to an individual branch circuit,

protected by the required time-delay fuses or circuit breakers. A

four or three-wire, single phase, 120/240V or 120/208V, 60Hz,

30 amp circuit is required.

If the electric supply does not meet the above specifications, then

call a licensed electrician.

GROUNDING INSTRUCTIONS

This dryer must be connected to a grounded metal, permanent

wiring system, or an equipment-gxounding conductor nmst be nm

with the circuit conductors and connected to the equipment-

grounding terminal on the appliance.

CONNECTING DRYER USING 4-WIRE

CONNECTION (MUST BE USED FOR

MOBILE HOME INSTALLATION)

NOTE: Since January 1, 1996, the National Electric Code

requires that new constructions utilize a 4 wire connection

to an electric dryer.

REMOVEGROUNDSTRAP-

ANDDISCARD.KEEPGREEN

GROUNDSCREW

HOT

WIRE RELOCATEGREEN

GROUNDSCREW

HERE

GREENOR

2 WITHUPTURNEDENDS(

Installation Instructions

1. Turn off the circuit breaker (s) (30 amp) or remove the dryer's

circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from tile wall receptacle.

3. Remove the power cord cover located at the lower back.

4. Remove and discard ground strap. Keep the green

ground screw for step 7.

5. Install 3/4 in. UL recognized strain relief to power

cord entry hole. Bring power cord through strain relief.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of

the terminal block (marked L1 and L2).

B. Connect the neutral (white) line to tile center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green ground

screw (hole above strain relief bracket). Tighten all

terminal block screws (3) completely.

8. Properly secure power cord to strain relief.

9. Reinstall the coven

,_WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

CONNECTING DRYER USING 3-WIRE

CONNECTION

IFREQUIRED,BYLOCALCODE,

INSTALLEXTERNALGROUND

(NOTPROVIDED)TOGROUNDED

METAL,COLDWATERPIPE,OR GREEN GROUND

OTHERESTABLISHEDGROUNDGROUND _TRAP

DETERMINEDBYAQUALIFIEDSCREW

ELECTRICIAN. HOT

WIRE

STRAINRELIEF

BRACKET

3/4",UL

RECOGNIZED

RELIEF

NEUTRAL

HOT

(White) WIRE

3#10AWGMINIMUMCOPPER

COVER CONDUCTORSOR120/240V30APOWER

SUPPLYCORDKITMARKEDFORUSE

WITHDRYERS&PROVIDEDWITHCLOSED

LOOPORSPADETERMINALSWITH

UPTURNEDENDS(NOTSUPPLIED).

1. Tm'n off the circuit breaker (s) (30 amp) or remove the dryer's

circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall.

3. Remove tile power cord cover located at the lower back.

4. Install 3/4 in. UL recognized strain relief to power cord

entry hole. Bring power cord through strain relief.

5. Connect power cord as Mlows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to neutral (center)

terminal of block and to green ground screw on cabinet

rear. Tighten all terminal block screws (3) completely.

7. Properly secure power cord to strain relief.

8. Reinstall tile cover.

,_WARNING: NEVER LEAVE THE

COVER OFF OF THE TERMINAL BLOCK.

[] EXHAUST INFORMATION

JIIWARNING - USE ONLY METAL 4-IN. DUCT.

DO NOT USE DUCT LONGER THAN SPECIFIED

IN THE EXHAUST LENGTH TABLE.

Using exhaust longer than specified length will:

• Increase the drying times and the energy cost.

• Reduce the dryer life.

• Accumulate lint, creating a potential fire hazard.

The correct exhaust installation is YOUR RESPONSIBILITY.

Problems due to incorrect installation are not covered

by the warranty.

The MAXIMUM ALLOWABLE length of the exhaust system

depends upon the type of duct, nmnber of turns, the type of

exhaust hood (wall cap), and all conditions noted below. Both

rigid and flexible metal duct are shown in the table below.

EXHAUST LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Use only for short

run installations

4"DIA.

Recommended

No. of 90_ Rigid Flexible Rigid Flexible

Elbows Metal Metal Metal Metal

0 90 Feet 55 Feet 60 Feet 45 Feet

1 60 Feet 40 Feet 45 Feet 30 Feet

2 45 Feet 30 Feet 35 Feet 20 Feet

3 35 Feet 20 Feet 25 Feet 15 Feet

4 25 Feet 15 Feet 15 Feet 10 Feet

If using flexible metal duct, please refer to page 5.

EXHAUST SYSTEM CHECK LIST

HOOD OR WALL CAP

• Terminate in a manner to prevent back draf& or entry of birds or

other wildlifK

• Termination should present minimal resistance to the exhaust air flow

and should require little or no maintenance to prevent clogging.

• Never install a screen in or over tfie exhaust duct. This could cause lint build up.

• Wall caps must be installed at least 12 in. above g_ound level or any other

obstruction with the opening pointed down.

• If roof vents or louvered plenums are used, they must be equivalent to a

4-in. dampened wall cap in regard to resistance to air flow, prevention of

back drafts, and maintenance required to prevent cloggting.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight duct,

including distance between last turn and exhaust hood.

TURNS OTHER THAN 90°

• One turn of 450 or less may be ignored.

• Two 450 turns should be treated as one 90 ° turn.

• Each turn over 45 o should be treated as one 900 turn.

SEALING OFJOINTS

•All joints should be tight to avoid leaks. The male end of each section of

duct must point away from the dryer.

•Do not assemble the ductwork with fasteners that extend into the duct.

They will serve as a collection point fbr lint.

•Duct joints can be made air and moisture-tight by wrapping the

overlapped joints with duct tape.

•Horizontal runs should slope down toward tile outdoors 1/2 inch per foot

INSULATION

Duct work that runs through an unheated area or is near air conditioning

should be insulated to reduce condensation and lint build-up.

Installation Instructions

[] EXHAUST CONNECTION

,_,WARNING - TO REDUCE THE RISK

OF FIRE OR PERSONAL INJURY:

• Exhausting the dryer to the outdoors is strongly recom-

mended to prevent large amounts of moisture from

being blown into the room.

• Use only metal duct.

• Do not terminate exhaust in a chimney, any gas vent,

under an enclosed floor (crawl space), or into an attic.

The accumulated lint could create a fire hazard.

• Provide an access for inspection and cleaning of the

exhaust system, especially at turns. Inspect and clean at

least once a year.

• Never terminate the exhaust into a common duct with a

kitchen exhaust. A combination of lint and grease could

create a fire hazard.

• Do not obstruct incoming or exhausted air.

THIS DRYER COMES READY FOR REAR

EXHAUSTING. IF SPACE IS LIMITED, USE

THE INSTRUCTIONS IN SECTION 9 TO

EXHAUST DIRECTLY FROM THE SIDES OR

BOTTOM OF THE CABINET,

STANDARD REAR EXHAUST

(Vented above floor level)

ELBOWHIGHLY

RECOMMENDED

ELBOWHIGHLY

_ RECOMMENDED

RECOMMENDED

= CONFIGURATION

TO MINIMI7E

EXHAUST

BLOCKAGE.

NOTE: ELBOWS WILL PREVENT DUCT

KINKING AND COLLAPSING.

STANDARD REAR EXHAUST

(Vented at floor level)

FORSTRAIGHT

LINEINSTALLATION,

CONNECTTHE

DRYEREXHAUST

TOTHEEXTERNAL

EXHAUSTHOODUSIN(

DUCTTAPEORCLAMR

CUTTHEMETALEXHAUST

DUCT(NOTSUPPLIED)TOTHE

PROPERLENGTH.

[] LEVELING AND STABILIZING

YOUR DRYER

STANDTHEDRYERUPRIGHTNEARTHEFINALLOCATIONANDADJUST

THE4LEVELINGLEGS,ATTHECORNERS,TOENSURETHATTHEDRYER

ISLEVELFROMSIDETOSIDEANDFRONTTOREAR.

LEVEL

FRON_TO-BACK, LEVEL

SIDE-TO-SIDE,

4LEVELING

LEGS

NOTE:WESTRONGLYRECOMMENDSOLIDMETALEXHAUSTDUCTING.

HOWEVER,IFFLEXIBLEDUCTINGISUSEDITMUSTBEMETALNOTPLASTIC. 4

Installation Instructions, Indoor Exhausting

USING FLEXIBLE METAL DUCTS

If rigid allmmtal duct cannot be used, then flexible allmmtal ducting

can be used, but it will reduce the maxinmnl recotmnended duct

length. In special installations when it is impossible to use only

metal ducting, then ULdisted clothes dryer flexible metal transition

duct may be used as transition venting between the dryer and wall

connection only. The use of this ducting will affect dry time.

If flexible transition duct is necessary, the following directions must

be followed.

• Use the Shortest Length Possible.

• Stretch the Duct to Its Maxinmm Length to avoid kinks.

• Do Not Crush or Collapse the Duct.

• Never Use Transition Duct Inside the Wall or

Inside the Dryer.

• Avoid Resting the Duct on Sharp Objects.

• Venting Must Conform to Local Building Codes.

ELBOWHIGHLY

RECOMMENDED

ELBOWSHIGHLY

DONOTUSE

EXCESSIVE

EXHAUST

)(

b ONOT

CRUSH

FLEXIBLE

EXHAUST

AGAINST

WALL._

)

INDOOR EXHAUSTING

NOTE: MOBILE HOME, BEDROOM, BATHROOM,

ALCOVE OR CLOSET INSTALLATIONS

MUST BE EXHAUSTED TO THE OUTDOORS

OTHER INSTALLATIONS: If tile installation makes it

impossible to exhaust to tile outdoors, a 4" exhaust

deflector (WE25X278) must be installed. A clearance of 8"

is required between tile rear of tile dryer and the wall, and

tile deflector should be pointing up.

NOTE: EXHAUSTING TO THE OUTDOORS IS

STRONGLY RECOMMENDED, EXHAUSTING

INDOORS MAY CAUSE LINT ACCUMULATION,

AND MOISTURE DAMAGE INCLUDING MOLD

AND MILDEW,

[] ALCOVE OR CLOSET INSTALLATION

• If your dryer is approved for installation in an alcove or

closet, it will be stated on a label on the dryer back.

• The dryer MUST be vented to the outdoors. See the

EXHAUST INFORMATION sections 3 & 4.

• Minimum clearance between dryer cabinet and adjacent

walls or other surfaces is:

0 in. either side

3 in. front and rear

• Minimum vertical space from floor to overhead cabinets,

ceiling, etc. is 52 in.

• Closet doors must be louvered or otherwise ventilated and

must contain a minimum of 60 sq. in. of open area equally

distributed. If the closet contains both a washer and a

dryer, doors must contain a minimum of 120 sq. in. of open

area equally distributed.

[] BATHROOM OR BEDROOM

INSTALLATION

• The dryer MUST be vented to the outdoors. See

EXHAUST INFORMATION section 3 & 4.

• Tile installation must conform with local codes or, in the

absence of local codes, with the NATIONAL ELECTRI-

CAL CODE, ANSI/NFPA NO. 70.

[] MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation must conform to the MANUFACTURED

HOME CONSTRUCTION & SAFETY STANDARD,

TITLE 24, PART 32-80 or, when such standard is not

applicable, with AMERICAN NATIONAL STANDARD

FOR MOBILE HOME, ANSI/NFPA NO. 50lB.

• The dryer MUST be vented to the outdoors with the

termination securely fastened to the mobile home

structure. (See EXHAUST INFORMATION

section 3 & 4.)

• The vent MUST NOT be terminated beneath a mobile or

manufactured home.

• The vent duct material MUST BE METAL.

• Do not use sheet metal screws or other fastening devices

which extend into the interior of the exhaust vent.

• See section 2 for electrical connection information.

Installation Instructions

[] DRYER EXHAUST TO RIGHT, LEFT

OR BOTTOM CABINET

iF=

I/A,WARNING- BEFORE PERFORMING

THIS EXHAUST INSTALLATION, BE SURE

TO DISCONNECT THE DRYER FROM ITS

ELECTRICAL SUPPLY. PROTECT YOUR

HANDS AND ARMS FROM SHARP EDGES

WHEN WORKING INSIDE THE CABINET.

BE SURE TO WEAR GLOVES

REMOVE

SCREW

ANDSAVE.

REMOVE

DESIRED

KNOCKOUT

(ONEONLY),

Detach and remove the bottom, right or left side knockout

as desired. Remove the screw inside the dryer exhaust duct

and save. Pull the duct out of the dryer.

FIXINGHOLE

{

B A

Cut the duct as shown and keep portion A.

TAB LOCATION

BENDTAB

UP45o

Through the rear opening, locate the tab in the middle of

the appliance base. Lift the tab to about 45° using a fiat

blade screwdriver.

ADDING NEW DUCT

FIXING

HOLE

_ PORTION"A"

RIGHTOR

LEFTSIDE

EXHAUST

Reconnect tile cut portion (A) of tile duct to tile blower

housing. Make sure that the shortened duct is aligned with

the tab in tile base. Use the screw saved previously to secure

tile duct in place through the tab on tile appliance base.

ADDING ELBOW AND DUCT FOR

EXHAUST TO LEFT OR RIGHT

SIDE OF CABINET

• Preassemble 4" elbow with 4" duct. _¥rap duct tape

around joint.

Insert duct assembly, elbow first, through tile side opening

and connect tile elbow to the dryer internal duct.

CAUTION: Be sure not to pull or damage the

electrical wires inside the dryer

when inserting the duct.

EXHAUSTCAN

BEADDEDTO

LEFTORRIGHTSIDE

DUCT

TAPE

Apply duct tape as shown on the joint between the dryer

internal duct and the elbow.

DUCT

CAUTION:

Internal duct joints must be

secured with tape, otherwise

they may separate and cause

a safety hazard.

Installation Instructions

ADDING ELBOW FOR EXHAUST

THROUGH BOTTOM OF CABINET

• Insert the elbow through tile rear opening and connect it to

the dryer internal duct.

• Apply duct tape on the joint between tile dryer internal

duct and elbow, as shown on page 6.

CAUTION:

Internal duct joints must be secured with tape,

otherwise they may separate and cause a

safety hazard.

ADDING COVER PLATE TO REAR

OF CABINET (SIDES AND BOTTOM

EXHAUST)

Connect standard metal elbows and ducts to complete tile

exhaust system. Cover back opening with a plate (Kit

WE 1M454) available from your local service provider.

Place dryer in final location.

- NEVER LEAVE THE BACK I

OPENING WITHOUT THE PLATL (KitWE1M454) I

IT0qCHANGING DIRECTION OF

DOOR OPENING

1. ()pen tile door and remove tile filler plugs opposite tile

hinges. _¥ith tile door completely open, remove the

bottom screws from each hinge on tile dryer face. Insert

these screws about halfway into tile TOP holes, for each

hinge on tile opposite side (where you removed tile filler

plugs). Apply firm pressure to get tile screw started.

2. Loosen tile top screws from each hinge on tile dryer face

halfway. _¥ith one hand holding the top of the door and

the other hand holding the bottom, remove the door

from the dryer by lifting it UP and OUT.

3. Rotate the door 180°. Insert the door on the opposite side

of the opening by moving the door IN and DOWN

until the top hinge and the bottom hinge are resting on

the top screws inserted in step 1.

4. Remove the remaining screws from the side of the

opening from which the door was removed. With these

screws secure each hinge at the bottom. Tighten the two

top screws on each hinge. Reinsert the plastic plugs on

the side from which the door was removed.

LOOSENTHETOP

REMOVETHE SCREWSFROM

BOTTOMSCREW EACHHINGEON

FROMEACHHINGE THEDRYERFACE

ONTHEDRYER HALFWAY.

MOVETHEDOORINAND

DOWNUNTILTHETOPHINGE

ANDTHEBOTTOMHINGEARE

RESTINGONTHETOPSCREWS

INSERTEDINSTEP1,

SECUREEACHHINGE

ATTHEBOTTOMAND

TIGHTENTHETWOTOP

SCREWSOFEACHHINGE.

TO REGISTER YOUR DRYER

CALL TOLL-FREE

1-888-269-1192

Promptregistrationconfirmsyour rightto protectionunderthe

termsof yourwarranty.

www.GEAppliances.com (US)

For Questions on Installation, Call: 1-800-626-2003 (US)

500A187PO_7 2 Ill ()N Ihlb # 31 15175

[] SERVICING

_k WARNING- LABEL ALL WIRES

PRIOR TO DISCONNECTING WHEN

SERVICING CONTROLS. WIRING

ERRORS CAN CAUSE IMPROPER AND

DANGEROUS OPERATION AFTER

SERVICING/IN STALLATION.

For servicing phone numbers for replacement parts, and

other information, refer to Owner's Manual or visit our

Web site.

Notes

GE DPSE592EA0AA Installation guide

GE DPSE592EA0AA Installation guide

GE DPSE592EA0AA Installation guide

Related papers

Other documents