© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30556 (0509) 1 of 10
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
SEP 2005
2005-2006 CR-V
PARTS LIST
Automatic Day/Night Mirror Attachment Kit
(sold separately)
P/N 08V03-S9A-101
Clip
Day/night mirror harness
Mirror harness
10 Wire ties
2 EPT sealer
Day/Night mirror
AUTOMATIC DAY/NIGHT
MIRROR
ATTACHMENT KIT
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
10 mm Combination wrench
Ratchet
8 mm, 10 mm and 14 mm Sockets
T20 and T25 Torx bits
Diagonal cutters
Torque wrench
Isopropyl alcohol
Shop towel
Piece of steel wire
Tape measure
Scissors
Electrical tape
Pliers
08V03-S9A-1000-91
Upper and lower covers
Illustration of the Day/Night Mirror Installed on
the Vehicle
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for the radio,
then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Owner’s Manual
4202061
H
DAY/NIGHT
MIRROR
MIRROR
HARNESS
DAY/NIGHT
MIRROR
HARNESS
FUSE CASE
(2A)
Automatic Day/Night Mirror Kit
(sold separately)
P/N 08V03-S9A-100B
AII 30556
Ground bolt
www.collegehillshonda.com/parts
2 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
3. Remove the lens from the roof console (four
retaining tabs).
4. Remove the roof console (four screws, and
unplug one connector).
6. Remove the sunvisor holders. Turn the holder
90°, then pull it out.
4130060
H
CONNECTOR
ROOF
CONSOLE
SCREW
ROOF
CONSOLE
LENS
RETAINING
TABS (4)
5. Remove the mirror by sliding the mirror up.
MIRROR
HOLDER
4130070
H
MIRROR
4130081
H
SUNVISOR
HOLDER
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30556 (0509) 3 of 10
7. Remove the cap from the right sunvisor (four
retaining tabs).
8. Remove the right sunvisor (two T25 Torx screws).
9. Remove the door opening weatherstrip from the
right front pillar in the area shown. Remove the
right front pillar trim (2 clips).
4130090
H
RETAINING
TABS (4)
CAP
TORX SCREW
RIGHT
SUNVISOR
4130100
H
CLIP
CLIP
Pull out part way
to release.
DOOR OPENING
WEATHERSTRIP
RIGHT FRONT
PILLAR TRIM
10. Remove the passenger’s dashboard under cover
(release the three clips and two pins.)
11. Open the glove box. Release the right and left
stops.
12. Remove the two screws from the bottom of the
glove box, and remove the glove box.
PINS (2)
PASSENGER’S
DASHBOARD
UNDER COVER
CLIPS (3)
STOPS (2)
SCREW
GLOVE
BOX
TABS (2)
4 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
13. Remove the right kick panel (pull to release the
two clips).
CLIP
RIGHT KICK
PANEL
TAB
TAB
14. Turn the knob clockwise, and remove the driver’s
dashboard under cover (one clip).
DRIVER’S
DASHBOARD
UNDER COVER
HOLDER
CLIP
KNOB
Turn
clockwise
90°.
15. Remove the driver’s dashboard lower cover:
• Remove the fuse box lid, and open the pocket.
• Remove the two self-tapping screws.
• Gently pull out on the driver’s dashboard lower
cover to release the eight clips. If equipped,
unplug the vehicle connector and remove the
lower cover.
16. Open the dashboard pocket lid. Using a flat-tip
screwdriver wrapped with tape, remove the screw
cover by releasing the two retaining clips and two
retaining tabs. Remove the dashboard pocket (one
self-tapping screw, then pull out to release the one
clip and three retaining tabs). If equipped, unplug
the vehicle connector.
4130110
H
CLIPS (8)
DRIVER’S
DASHBOARD
LOWER
COVER
VEHICLE CONNECTOR
(If equipped.)
POCKET
VEHICLE CONNECTOR
(If equipped.)
SELF-TAPPING
SCREW
FUSE
BOX
LID
HOOKS (2)
CLIP
RETAINING
TABS (2)
2829302
K
CLIP
SELF-
TAPPING
SCREW
RETAINING
TABS (2)
SCREW
COVER
RETAINING TABS (2)
DASHBOARD
POCKET
SMALL
FLAT-TIP
SCREWDRIVER
TAPE
RETAINING TAB
VEHICLE
CONNECTOR
(If equipped)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30556 (0509) 5 of 10
17. Remove two self-tapping screws that fasten the
heater A/C control panel to the dashboard. Pull
the heater A/C control panel out toward you to
release the four clips. Unplug the vehicle
connector, and remove the heater A/C control
panel.
18. On A/T vehicles only, remove the two clips and
six self-tapping screws, and pull the dashboard
center lower cover out toward you to release the
six clips. Unplug the vehicle 2-pin connector from
the accessory socket, then remove the cover.
19. On M/T vehicles only, remove the four seat track
end covers from the driver’s seat, then remove the
four bolts that secure the seat.
20. On M/T vehicles only, pull the shift boot down
while holding the plastic clip. Remove the shift
knob from the shift lever by turning it
counterclockwise.
BOLTS (4)
DRIVER’S
SIDE SEAT
SEAT TRACK
END COVERS (4)
SHIFT KNOB
Turn
counterclockwise
to remove.
SHIFT BOOT
Pull down
PLASTIC
CLIP
4130130
H
CLIPS (4)
SELF-TAPPING
SCREW
HEATER A/C
CONTROL
PANEL
VEHICLE
CONNECTOR
4404301
T
VEHICLE 2-PIN
CONNECTOR
DASHBOARD
CENTER
LOWER
COVER
SELF-
TAPPING
SCREWS (6)
CLIPS (2)
CLIP
CLIPS (4)
Pull toward you.
6 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
24. Plug the mirror harness 7-pin connector into the
rear of the mirror, then route the 4-pin connector
up and out through the console opening in the
roof lining as shown.
21. On M/T vehicles only, remove the two side covers
(four tabs) from the center console.
22. On M/T vehicles only, remove the two clips and
seven self-tapping screws, and pull the front
console out toward you to release four clips.
Unplug the vehicle 2-pin connector from the
accessory socket, then remove the front console.
4130150
H
CONSOLE OPENING
IN ROOF LINING
ROOF LINING
MIRROR
HARNESS
MIRROR HARNESS
7-PIN CONNECTOR
DAY/NIGHT
MIRROR
MIRROR
HARNESS
4-PIN
CONNECTOR
23. Slide the day/night mirror stay onto the mirror
holder, then tighten the T20 Torx screw installed on
the day/night mirror.
4130140
H
MIRROR
HOLDER
MIRROR
STAY
DAY/NIGHT
MIRROR
TORX
SCREW
4404311
T
Pull
VEHICLE 2-PIN
CONNECTOR
CLIPS (2)
SELF-TAPPING
SCREWS (7)
CLIPS (2)
TABS (4)
SIDE
COVER
SIDE COVER
TABS (4)
CLIP
FRONT
CONSOLE
ILLUMINATION
BULB
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30556 (0509) 7 of 10
25. Route the mirror harness through the grooves of
the upper and lower covers. Attach the lower
cover to the stay of the mirror.
26. Slide the upper cover up and under the roof lining
as shown.
ROOF LINING
MIRROR
HARNESS
LOWER
COVER
DAY/NIGHT
MIRROR STAY
DAY/NIGHT
MIRROR
UPPER
AND
LOWER
COVERS
27. Unplug the vehicle connectors (gray) and
disengage the clip installing the vehicle 21-pin
connector (white) to the right center frame.
28. Unplug the vehicle 21-pin connector (white) and
connect the day/night mirror harness 21-pin
connectors between the vehicle 21-pin
connectors (white).
29. Remove the connector clip from the vehicle 21-pin
connector (white) and install the new clip supplied
with the kit onto the vehicle 21-pin connector.
30. Reconnect the vehicle connector (gray) and attach
the clip you just installed on the vehicle 21-pin
connector (white) to the right center frame.
4129020
H
VEHICLE 21-PIN
CONNECTOR (white)
DAY/NIGHT MIRROR
HARNESS
DAY/NIGHT MIRROR
HARNESS 21-PIN
CONNECTOR
4129030H
VEHICLE 21-PIN
CONNECTOR
(white)
CLIP
CONNECTOR
CLIP (Discard.)
VEHICLE 21-PIN
CONNECTOR
VEHICLE
CONNECTOR
(gray)
RIGHT CENTER
FRAME
4129010
H
CLIP
RIGHT CENTER
FRAME
VEHICLE 21-PIN
CONNECTOR
(white)
VEHICLE
CONNECTOR
(gray)
RIGHT CENTER
FRAME
8 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
31. Route the day/night mirror harness 4-pin connector
with fuse case upwards to the vehicle harness,
and then along the vehicle harness to the fuse box
through the dashboard pocket opening.
32. Connect the day/night mirror harness 4-pin
connector to the accessory terminal of the fuse
box.
33. Route the day/night mirror harness ground terminal
to the right along the vehicle harness at the rear of
the glove box frame.
4130010
H
DAY/NIGHT
MIRROR
HARNESS 4-PIN
CONNECTOR
DAY/NIGHT
MIRROR
HARNESS
FUSE BOX
ACCESSORY
TERMINAL
LOCATION
34. Remove and discard the instrument panel bracket
bolt, and secure the day/night mirror harness
ground terminal to the instrument panel bracket
with the new ground bolt supplied.
4129040
H
FUSE
BOX
VEHICLE HARNESS
DASHBOARD
POCKET OPENING
DAY/NIGHT
MIRROR
HARNESS
SHIFT
LEVER
CABLE
DAY/NIGHT
MIRROR
HARNESS
4-PIN
CONNECTOR
DAY/NIGHT
MIRROR
HARNESS
FUSE CASE
4130022
H
GLOVE BOX
OPENING
VEHICLE
HARNESS
DAY/NIGHT
MIRROR
HARNESS
DAY/NIGHT
MIRROR
HARNESS
GROUND
TERMINAL
GROUND
BOLT
INSTRUMENT
PANEL
BRACKET
BOLT
(Discard.)
© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30556 (0509) 9 of 10
4202010
H
DAY/NIGHT MIRROR HARNESS
4-PIN CONNECTOR
INSTRUMENT
PANEL
DAY/NIGHT
MIRROR
HARNESS
4-PIN
CONNECTOR
ELECTRICAL
TAPE
PIECE OF
STEEL
WIRE
RIGHT FRONT
PILLAR
35. Tape a piece of steel wire to the 4-pin connector
end of the day/night mirror harness. Route the
harness end up along the instrument panel side
bracket, and out through the clearance between
the right front pillar and the instrument panel as
shown.
36. Remove the electrical tape and the steel wire
from the day/night mirror harness.
38. Connect the day/night mirror harness 4-pin
connector to the mirror harness 4-pin connector.
39. Secure the three clips from the day/night mirror
harness into the holes in the right front pillar.
40. Using isopropyl alcohol, clean the areas where
the cushion tapes will attach. Using scissors, cut
two EPT sealers in half. Secure the day/night
mirror harness to the roof panel with three EPT
sealers.
41. Using the remaining half of EPT sealer, secure
day/night mirror harness 4-pin connector to the
roof panel.
4202020
H
4-PIN
CONNECTOR
MIRROR
HARNESS
DAY/NIGHT
MIRROR
HARNESS
ROOF CONSOLE
OPENING
HEAD
LINER
RIGHT
FRONT
PILLAR
37. Continue routing the day/night mirror harness 4-pin
connector up along the right front pillar, and out
through the roof console opening behind the head
liner.
4130040H
DAY/NIGHT
MIRROR
HARNESS
CLIP
RIGHT FRONT
PILLAR
DAY/NIGHT
MIRROR
HARNESS
4130052
H
4-PIN
CONNECTOR
EPT SEALER (Half)
remaining from step 40
DAY/NIGHT
MIRROR
HARNESS
EPT SEALER
(Half: 3)
EPT SEALER
10 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
44. Under the dashboard, secure the day/night mirror
harness to the vehicle harness with three wire
ties.
45. Check that all wire harnesses are routed properly
and all connectors are plugged in.
46. Reinstall the driver’s side seat, torque the driver’s
seat bolts to 32 to 38 N·m (24 to 28 lb·ft)
47. Reinstall all removed parts. Check that all clips
and other fasteners are installed securely.
48. Reconnect the negative cable to the battery.
49. Set the clock, and reset the radio station presets.
50. Check the operation of the automatic day/night
mirror according to the Owner’s Manual supplied.
NOTE: Whenever the battery is disconnected, the
driver’s AUTO function is disabled.
51. Start the engine. Push down on the driver’s
window switch until the window is fully open.
52. Pull up on the driver’s window switch fully to close
the window completely, then hold the switch for 2
seconds.
53. Test the driver’s window AUTO function.
4202051
H
DAY/NIGHT
MIRROR
HARNESS
VEHICLE
HARNESS
WIRE TIE
42. Secure the day/night mirror harness to the vehicle
harness with four wire ties.
4202032
H
WIRE TIE
DAY/
NIGHT
MIRROR
HARNESS
WIRE TIE
VEHICLE
HARNESS
43. Secure the day/night mirror harness to the vehicle
harness with three wire ties.
4202040
H
DAY/NIGHT MIRROR
HARNESS
VEHICLE
HARNESS
WIRE TIE
/