WEG Hydrogenerators SH11 line brushless horizontal User manual

Motors I Automation I Energy I Transmission & Distribution I Coatings

Hydrogenerators

SH11 Line

Brushless - horizontal

Installation, Operation and Maintenance Manual

Document Number: 13607224

Model: SH11

Language: English

Revision: 02

July 2018

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 5

Dear Customer,

Thank you for purchasing a WEG generator. Our products are developed with the highest standards

of quality and efficiency which ensures outstanding performance.

Electricity plays a major role in the comfort and well-being of mankind. Since the generator is

responsible for generating this energy, it must be identified and treated as an electrical machine,

whose features require certain precautions, such as for storage, installation and maintenance.

All efforts have been made to ensure that the information contained in this manual is faithful to the

configurations and operation of the generator.

Therefore, we recommend that you read this manual carefully before proceeding with the installation,

operation or maintenance of the generator in order to ensure safe and reliable operation of your

equipment and facility. If you need any further information, please contact WEG.

Always keep this manual close to the generator, so it can be consulted whenever necessary.

ATTENTION

1.

It is imperative to follow the procedures contained in this manual for the warranty to be valid;

2.

The generator installation, operation and maintenance procedures must be performed only by qualified

personnel.

NOTES

1.

The total or partial reproduction of information supplied in this manual is authorized, provided that

reference is made to its source.

2.

If this manual is lost, an electronic PDF file is available at www.weg.net or another printed copy may be

requested.

WEG EQUIPAMENTOS ELÉTRICOS S.A.

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 7

INDEX

1

INTRODUCTION ............................................................................................... 11

1.1 SAFETY WARNINGS IN THE MANUAL ........................................................................................... 11

2

GENERAL INSTRUCTIONS ............................................................................... 12

2.1 QUALIFIED PERSONNEL ................................................................................................................ 12

2.2 SAFETY INSTRUCTIONS ................................................................................................................ 12

2.3 STANDARDS ................................................................................................................................... 12

2.3.1 Brazilian Standards ............................................................................................................................. 12

2.3.2 International Standards ....................................................................................................................... 12

2.4 ENVIRONMENTAL CONDITIONS .................................................................................................... 13

2.5 OPERATING CONDITIONS ............................................................................................................. 13

2.6 VOLTAGE AND FREQUENCY ......................................................................................................... 13

3

RECEIVING, HANDLING AND STORAGE ........................................................... 14

3.1 RECEIVING ..................................................................................................................................... 14

3.2 HANDLING ...................................................................................................................................... 14

3.3 STORAGE ....................................................................................................................................... 15

3.3.1 Outdoor storage ................................................................................................................................. 15

3.3.2 Extended storage ............................................................................................................................... 15

3.3.2.1 Storage location .................................................................................................................. 15

3.3.2.1.1 Indoor storage ................................................................................................ 15

3.3.2.1.2 Outdoor storage ............................................................................................. 15

3.3.2.2 Separate parts .................................................................................................................... 16

3.3.2.3 Space heater ....................................................................................................................... 16

3.3.2.4 Insulation resistance ............................................................................................................ 16

3.3.2.5 Exposed machined surfaces ................................................................................................ 16

3.3.2.6 Bearings .............................................................................................................................. 16

3.3.2.7 Terminal box ....................................................................................................................... 16

3.3.2.8 Inspections and records during storage ............................................................................... 17

3.3.2.9 Maintenance plan during storage ......................................................................................... 17

3.3.3 Preparation for commissioning ............................................................................................................ 18

3.3.3.1 Cleaning .............................................................................................................................. 18

3.3.3.2 Bearing inspection ............................................................................................................... 18

3.3.3.3 Bearing lubrication ............................................................................................................... 18

3.3.3.4 Insulation resistance verification ........................................................................................... 18

3.3.3.5 Others ................................................................................................................................. 18

4

INSTALLATION ................................................................................................. 19

4.1 INSTALLATION SITE ....................................................................................................................... 19

4.2 SHAFT LOCK .................................................................................................................................. 19

4.3 ROTATION DIRECTION ................................................................................................................... 19

4.4 INSULATION RESISTANCE ............................................................................................................. 19

4.4.1 Safety instructions .............................................................................................................................. 19

4.4.2 General considerations ....................................................................................................................... 19

4.4.3 Measurement on the stator windings................................................................................................... 19

4.4.4 Measurement on the rotor and exciter windings .................................................................................. 20

4.4.5 Additional Information ......................................................................................................................... 20

4.4.6 Polarization index ................................................................................................................................ 20

4.4.7 Conversion of the measured values ..................................................................................................... 20

4.4.8 Insulation assessment ......................................................................................................................... 21

4.5 PROTECTIONS ............................................................................................................................... 21

4.5.1 Thermal protections ............................................................................................................................ 21

4.5.1.1 Temperature sensors .......................................................................................................... 21

4.5.1.2 Temperature limits for the windings ..................................................................................... 22

4.5.1.3 Alarm and trip temperatures ................................................................................................ 22

4.5.1.4 Temperature and ohmic resistance of the PT100 thermoresistance ..................................... 23

4.5.2 Protections in the panel ...................................................................................................................... 23

4.5.3 Space heater ...................................................................................................................................... 23

4.6 COOLING ........................................................................................................................................ 23

4.7 ELECTRICAL ASPECTS .................................................................................................................. 24

4.7.1 Electrical connections ......................................................................................................................... 24

4.7.1.1 Main electrical connections.................................................................................................. 24

www.weg.net

8 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 1

3607224

4.7.1.2 Accessories connection ...................................................................................................... 24

4.7.2 Grounding ...........................................................................................................................................24

4.8 MECHANICAL ASPECTS ............................................................................................................... 24

4.8.1 Foundations ........................................................................................................................................24

4.8.2 Foundation loads ................................................................................................................................24

4.8.3 Base types ..........................................................................................................................................24

4.8.3.1 Concrete base .................................................................................................................... 24

4.8.3.2 Metal base ......................................................................................................................... 25

4.8.4 Natural frequency of the base ..............................................................................................................25

4.8.5 Mounting ............................................................................................................................................25

4.8.6 Anchor plate set ..................................................................................................................................25

4.8.7 Leveling ..............................................................................................................................................25

4.8.7.1 Support .............................................................................................................................. 26

4.8.8 Alignment ............................................................................................................................................26

4.8.9 Inspection of pedestal bearings ...........................................................................................................27

4.8.10 Couplings ...........................................................................................................................................27

4.8.10.1 Direct coupling ................................................................................................................... 28

4.8.10.2 Coupling of generators equipped with sleeve bearings ........................................................ 28

4.8.11 Bearing loads ......................................................................................................................................28

4.8.12 Magnetic center ..................................................................................................................................28

4.9 BRAKE ........................................................................................................................................... 29

4.10 HYDRAULIC UNIT .......................................................................................................................... 29

5

OPERATION PRINCIPLE .................................................................................... 30

5.1 EXCITATION ................................................................................................................................... 31

5.2 DE-EXCITATION ............................................................................................................................. 31

5.3 VOLTAGE REGULATOR ................................................................................................................. 31

6

COMMISSIONING ............................................................................................. 32

6.1 PRELIMINARY INSPECTION .......................................................................................................... 32

6.2 FIRST OPERATION (WITH NO LOAD)............................................................................................. 32

6.3 OPERATION ................................................................................................................................... 33

6.3.1 Connection to the load or electric power system (Grid) ........................................................................33

6.3.2 Synchronization of the generator with the power grid ..........................................................................33

6.3.3 Data recording ....................................................................................................................................33

6.3.4 Temperatures......................................................................................................................................34

6.3.5 Bearings .............................................................................................................................................34

6.3.5.1 High-pressure oil injection system ....................................................................................... 34

6.3.6 Vibration .............................................................................................................................................34

6.3.7 Vibration causes ..................................................................................................................................34

6.4 SHUTDOWN ................................................................................................................................... 34

7

MAINTENANCE ................................................................................................. 35

7.1 GENERAL ....................................................................................................................................... 35

7.2 GENERAL CLEANING .................................................................................................................... 35

7.3 WINDING INSPECTIONS ................................................................................................................ 35

7.4 WINDING CLEANING ..................................................................................................................... 35

7.4.1 Inspections .........................................................................................................................................36

7.4.2 Re-impregnation .................................................................................................................................36

7.4.3 Insulation resistance .............................................................................................................................36

7.5 COOLING SYSTEM MAINTENANCE ................................................................................................ 36

7.6 VIBRATION ..................................................................................................................................... 36

7.7 SHAFT GROUNDING DEVICE ........................................................................................................ 36

7.8 EXCITER MAINTENANCE ............................................................................................................... 36

7.8.1 Exciter.................................................................................................................................................36

7.8.2 Insulation resistance ............................................................................................................................36

7.8.3 Diode test ...........................................................................................................................................36

7.8.3.1 Diode Replacement ............................................................................................................ 37

7.8.4 Varistor test .........................................................................................................................................37

7.8.4.1 Varistor replacement ........................................................................................................... 37

7.9 BEARING MAINTENANCE .............................................................................................................. 37

7.9.1 Bearing data .......................................................................................................................................37

7.9.2 Bearing installation and operation ........................................................................................................37

7.9.3 Oil change ...........................................................................................................................................38

7.9.4 Sealing ................................................................................................................................................38

7.9.5 Sleeve bearing operation .....................................................................................................................38

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 9

7.9.6 Sleeve bearing maintenance ............................................................................................................... 38

7.9.7 Bearing protection setting ................................................................................................................... 39

7.9.8 Disassembly/assembly of the bearing temperature sensors ................................................................. 39

8

GENERATOR DISASSEMBLY AND ASSEMBLY .................................................. 40

8.1 DISASSEMBLY ............................................................................................................................... 40

8.2 ASSEMBLY ..................................................................................................................................... 40

8.3 TIGHTENING TORQUE ................................................................................................................... 40

8.4 AIR GAP MEASURMENT................................................................................................................. 41

8.5 SPARE PARTS ................................................................................................................................ 41

9

MAINTENANCE PLAN ....................................................................................... 42

10

ABNORMALITIES, CAUSES AND SOLUTIONS ................................................... 43

11

DECLARATION OF CONFORMITY ..................................................................... 45

12

ENVIRONMENTAL INFORMATION ..................................................................... 46

12.1 PACKAGE ....................................................................................................................................... 46

12.2 PRODUCT ....................................................................................................................................... 46

12.3 HAZARDOUS WASTE ..................................................................................................................... 46

13

WARRANTY TERM ........................................................................................... 47

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 11

1 INTRODUCTION

This manual contains information regarding synchronous generators SH11.

The generators are supplied with specific documents (drawings, connection diagram, characteristic curves, etc.). Those

documents, together with this manual, must be thoroughly evaluated before proceeding with the installation, operation or

maintenance of the generator.

All the procedures and standards contained in this manual must be observed in order to ensure proper operation of the

generator and the safety of the personnel involved. Following these procedures is also important to ensure the validity of the

generator warranty. Thus, we recommend carefully reading this manual before performing the installation, operation or

maintenance of the generator. If you need any further information, consult WEG.

1.1 SAFETY WARNINGS IN THE MANUAL

In this manual, the following safety warnings are used:

DANGER

Failure to observe the procedures recommend in this warning may result in death, serious injuries and

extensive equipment damage.

ATTENTION

Failure to observe the procedures recommend in this warning may result in equipment damage.

NOTE

This provides important information for correct understanding and proper operation of the product.

www.weg.net

12 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 13607224

2 GENERAL INSTRUCTIONS

All personnel involved with the assembly, operation or maintenance of electrical installations must be informed and updated

on the standards and safety instructions that guide the job and are advised to strictly comply with them. Before beginning

any job, the person in charge must make sure that all points have been duly observed and warn the respective personnel

about the danger inherent to the task to be performed.

Improper application, inadequate handled or maintenance of the generator, may cause serious injuries and/or material

damages. Therefore, it is highly recommended that such jobs be always performed by qualified personnel.

2.1 QUALIFIED PERSONNEL

The term qualified personnel means those who, because

of their training, experience, education level and

knowledge of the applicable standards, specifications,

accident prevention, safety standards and operating

conditions, have been authorized by the persons in charge

to execute the necessary tasks, and who are able to

recognize and avoid any possible danger.

Such qualified personnel must also know and be able to

provide first aid procedures if necessary.

The entire start-up, maintenance and repair tasks must

only be performed by qualified personnel.

2.2 SAFETY INSTRUCTIONS

DANGER

During normal operation of this equipment, a

hazard associated with energized or rotating

components with high voltage or elevated

temperatures exists.

Thus,

the operation with open terminal

boxes, unprotected couplings, improper

handling, or failure to comply with the

operating standards, may cause severe

personal injuries and material damages.

ATTENTION

When devices and equipment are used

outside the industrial environment, the user

must ensure the safety of the equipment by

adopting proper protection and safety

measures during installation (for example,

keeping people away, avoiding contact of

children, etc.).

Those responsible for the safety of the installation must

ensure that:

 Only qualified personnel install and operate the

equipment;

 They have this manual and all other documents

supplied with the generator at hand, as well as that they

perform the tasks in strict compliance with the service

instructions, relevant standards and specific product

documentation.

ATTENTION

Failure to comply with installation and safety

standards may void the product warranty.

Firefighting equipment and first aid notices

must be available in visible and easily

accessible locations at the work site.

Qualified personnel must also observe:

 All the technical data regarding the allowed applica

tions

(operating conditions, connections and installation

environment), provided in the purchase order

documents, operating instructions, manuals and other

documentation;

 The specific regulations and conditions for the loca

l

installation;

 The use of suitable tools and equipment for handling

and transportation;

 That the protective devices of the individual

components are removed shortly before installation.

Individual parts must be stored in vibration-free

environments, avoiding falls and ensuring their protection

against aggressive agents and/or that they do not

jeopardize people.

2.3 STANDARDS

The generators are specified, designed, manufactured and

tested according to the standards described in items

2.3.1 and 2.3.2.

The applicable standards are specified in the commercial

contract. May indicate other national or international

standards, depending on the application or installation

location.

2.3.1

Brazilian Standards

 NBR 15623-2, Maquinas elétricas girantes - Dimensões

e

series de potências para máquinas elétricas girantes –

Padronização Parte 2: Designação de carcaças entre

355 a 1000 e flanges entre 1180 a 2360;

 ABNT NBR 5117:2007, Máquina elétrica girante –

Máquina Síncrona – Especificação;

 ABNT NBR 5052:1984, Máquina Síncrona – Ensaios;

 ABNT NBR 6158:1995, Sistema de tolerância e ajustes;

 ABNT NBR IEC60034-5, Maquinas elétricas girantes –

Parte 5: Graus de proteção proporcionados pelo

projeto completo de máquinas elétricas girantes

(código IP) – classificação;

 ABNT NBR IEC60034-6, Maquinas elétricas girantes –

Parte 6: Métodos de resfriamento (código IC)

 ABNT NBR IEC60034-7, Maquinas elétricas girantes –

Parte 7: Classificação dos tipos de construção, arranjos

de montagem e posição da caixa de terminais (código

IM)

 ABNT NBR IEC60034-9, Maquinas elétricas girantes –

Parte 9: Limites de Ruído.

ABNT NBR IEC60034-14, Maquinas elétricas girantes –

Parte 14: Medição, avaliação e limites da severidade de

vibração mecânica de máquinas de altura de eixo igual ou

superior a 56mm.

2.3.2

International Standards

 IEC-60072-2, Dimensions and output series for rotati

ng

electrical machines – Part 2: Frame numbers 355 to

1000 and flange numbers 1180 to 2360;

 IEC60034-1 Rotating electrical machines – Part 1:

Rating and performance

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 13

 IEC60034-2-1 Rotating electrical machines – Part 2-1:

Standard methods for determining losses and efficiency

from tests (excluding machines for traction vehicles)

 IEC60034-4 Rotating electrical machines – Part 4:

Methods for determining synchronous machine

quantities from tests

 IEC60034-5 Rotating electrical machines – Part 5:

Degrees of protection provided by the integral design of

rotating electrical machines (IP code) – classification

 IEC60034-6 Rotating electrical machines – Part 6:

Methods of cooling (IC code)

 IEC60034-7 Rotating electrical machines – Part 7:

Classification of types of construction, mounting

arrangements and terminal box position (IM code)

 IEC60034-8 Rotating electrical machines – Part 8:

Terminal markings and direction of rotation

 IEC60034-9 Rotating electrical machines – Part 9:

N

oise limits

 IEC60034-14 Rotating electrical machines – Part 14:

Mechanical vibration of certain machines with shaft

heights 56mm and higher – Measurement, evaluation

and limits of vibration severity

 ISO286-1 Geometrical product specifications (GPS) –

ISO code system for tolerances on linear sizes – Part 1:

Basis of tolerances, deviations and fits

 ISO286-2 Geometrical product specifications (GPS) –

ISO code system for tolerances on linear sizes – Part 2:

Tables of standard tolerance classes and limit

deviations for holes and shafts

 ISO1940-1 Mechanical vibration – Balance quality

requirements for rotors in a constant (rigid) state – Part

1: Specification and verification of balance tolerances;

ISO10816-5 Mechanical vibration – Evaluation of machine

vibration by measurements on non-rotating parts – Part 5:

Machine sets in hydraulic power generating and pumping

plants.

2.4 ENVIRONMENTAL CONDITIONS

The generators was designed according to the specific

environment characteristics (temperature and altitude) of

your application, and are described on the nameplate and

in the datasheet of the generator.

2.5 OPERATING CONDITIONS

In order for the product warranty to be valid, the generator

must operate according to the rated data indicated on its

nameplate, observing the applicable standards and the

information provided in this manual.

2.6 VOLTAGE AND FREQUENCY

The generator must be able to perform its main function

continuously in Zone A, but it does not have to fully meet

its performance characteristics at rated voltage and

frequency (refer to the point with rated characteristics in

Figure 2.1), and it may present some deviations. The

temperature rises may be above those at rated voltage

and frequency.

The generator must be able to perform its main function in

Zone B, but it may present greater deviations of its

performance at rated voltage and frequency than in Zone

A. The temperature rises may be higher than those

observed at rated voltage and frequency and, most likely,

will be higher than those in Zone A.

Prolonged operation in the periphery of Zone B is not

recommended.

Figure 2.1: Voltage and frequency variation limits (IEC60034-1)

Frequency (pu)

Zone B (outside zone A)

Point of rated conditions

Zone A

Voltage (pu)

www.weg.net

14 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 13607224

3 RECEIVING, HANDLING AND STORAGE

3.1 RECEIVING

All generators were tested and are in perfect operating

conditions. The machined surfaces are protected against

corrosion. The package must be inspected upon receipt

for occasional damages during transportation.

ATTENTION

Any damage must be

photographed,

documented and reported immediately to the

carrier, the insurer and WEG. The non-

communication of this damage will void the

warranty.

ATTENTION

Parts supplied in additional packages must

be checked upon receipt.

 When lifting the package (or container), the proper

hoisting points, the weight indicated on the package or

on the nameplate, and the operating capacity of the

hoisting equipment must be observed.

 Generators packed in wooden crates must always be

lifted by their own hoisting eye or by a proper forklift;

they must never be lifted by the package;

 The package can never be overturned. Place it on the

floor carefully (without impact) in order to avoid damage

to the bearings;

 Do not remove the grease for protection against

corrosion from the shaft end and, or the closing plugs

present in the terminal box holes. These protections

must remain in place until the moment of the final

assembly.

 A complete visual inspection of the generator must

be

carried out after removing the package;

 The shaft locking system must be removed just before

the installation and stored to be used in future

transportation of the generator.

3.2 HANDLING

Figure 3.1: Handling - generators IM1001/1005

For handling the hydro generator SH11 with mounting

IM1001/1005 assembled, they should only be used the

lifting lugs suitable for this purpose, as shown in Figure

3.1.

ANCHOR BASE

Figure 3.2: Handling - generators IM7311/7315

For handling the hydro generator SH11 with mounting

IM7311 / 7315 assembled, they should only be used the

lifting lugs on the anchor base, as shown in Figure 3.2.

If the lifting of the generator through the frame lifting lugs is

inevitable, WEG must be consulted.

ATTENTION

 The air guides and other devices that may

have contact with the chains, shackles,

etc. (If any) must be removed.

 The ventilation box, heat exchanger and

other devices that might have contact with

the chains, shackles, etc. They must be

removed.

 Steel wire ropes, clevises and the lifting

e

quipment must be able to stand the

generator weight.

 For handling and assembling generators

supplied disassembled, refer to the

handling and assembly manual supplied

with the generator.

NOTES

 Observe the indicated weight. Do not lift

the generator causing jolts or put it down

abruptly on the floor, because this can

cause damage to the bearings;

 The lifting lugs on the heat exchanger,

end shields, bearings, radiator, terminal

box, etc. are designed to handle these

components only separately;

 Never use the shaft to lift the generator;

 In order to move the generator, the shaft

must be locked with the shaft locking

device supplied with the generator.

FRAME LIFTING LUGS

Use for handling only the

frame in the event of

generator assembly or

disassembly.

Do not use them to handle

the complete generator.

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 15

3.3 STORAGE

If the generator is not installed immediately after reception,

it must remain inside the package and stored in a location

protected against moisture, vapors, sudden changes in

temperature, rodents and insects.

The generator must be stored in vibration-free locations in

order to avoid bearing damage.

ATTENTION

Space heaters must remain powered during

storage in order to avoid water condensation

inside the generator.

Any damage to the paint or corrosion

protection of the machined parts must be

repaired.

3.3.1

Outdoor storage

The generator must be stored in a dry location, free of

flooding and vibrations.

Repair all damages occasionally caused to the packing

during transportation before storing the generator, which

is necessary to ensure proper storage conditions.

Place the generator on platforms or foundations which

ensure protection against humidity from the ground and

prevent it from sinking into the soil. Free air circulation

underneath the generator must be assured.

The cover used to protect the generator against the bad

weather must not be in contact with its surfaces. In order

to ensure free air circulation between the generator and

such covers, place wooden blocks as spacers.

3.3.2

Extended storage

When the generator is stored for a long period (two

months or more) before the start-up, it is exposed to

external agents, such as temperature variations,

moisture, aggressive agents, etc.

Empty spaces inside the generator, such as those in

bearings, terminal box, and windings, are exposed to

humidity, which may condense and, depending on the

type and degree of air contamination, aggressive

substances may also penetrate these empty spaces.

Consequently, after long periods of storage, the winding

insulation resistance may drop below the acceptable

values, internal components, such as bearings, may

oxidize, and the lubricant power of the lubricant agent in

the bearings may be adversely affected.

All of these influences increase the risk of damages before

the generator start-up.

ATTENTION

For the generator warranty to be valid, it is

necessary to make sure that all the

preventive measures described in this

manual, as well as constructive aspects,

maintenance, packing, storage and

periodical inspections be followed and

recorded.

The extended storage instructions are valid for

generators that remain stored for long periods (two

months or more) before start-up or generators already

installed and that are in a prolonged stoppage,

considering the same period.

3.3.2.1

Storage location

In order to ensure the best storage conditions for the

generator during long periods, the chosen location must

strictly meet the criteria described in sections 3.3.2.1.1

and 3.3.2.1.2.

3.3.2.1.1

Indoor storage

 The storage site must be closed and covered;

 The site must be protected against moisture, vapors,

aggressive agents, rodents and insects;

 Corrosive gases, such as chlorine, sulfur dioxide or

acids, must not be present;

 The site must be free of vibration;

 The site must have a ventilation system with air fil

ter;

 Ambient temperature between 5 °C and 60 °C, without

sudden temperature variations;

 Relative humidity < 50%;

 The site must be protected against dirt and dust

accumulation;

 It must have a fire detection system;

 The location must have a power supply for the space

heaters.

If any of these requirements is not met in the storage site,

WEG recommends that additional protections be

incorporated to the generator package during the storage

period, as follows:

 A closed wooden crate or the like with an electrical

installation that allows the energization of the space

heaters;

 If there is risk of infestation and fungus formation, the

package must be protected in the storage location by

spraying it or painting it with appropriate chemicals;

 The package must be prepared carefully by an

experienced person.

3.3.2.1.2

Outdoor storage

ATTENTION

Outdoor storage of the generator is not

recommended.

In case outdoor storage is unavoidable, the generator must

be packed in a specific package for such condition, as

follows:

 For outdoor storage (exposed to the weather), besides the

package recommended for indoor storage, the package

must be covered with protection against dust, moisture

and other foreign materials, using resistant canvas or

plastic.

 The package must be placed on platforms or foundations

that ensure protection against dirt and moisture and keep

it from sinking into the soil;

 After the package is covered, a shelter must be erected to

protect it against direct rain, snow and excessive sun heat.

ATTENTION

In case the generator remains stored for long

periods (two months or more), it is

recommended to inspect it regularly as

specified in the section 3.3.2.9

of this

manual.

www.weg.net

16 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 13607224

3.3.2.2

Separate parts

 If parts are supplied separately (terminal boxes, end

shields, etc.), these parts must be packed as specified

in sections

3.3.2.1.1

and

3.3.2.1.2

of this manual.

 The relative humidity inside the package must not

exceed 50%.

 Rolling bearings must not be subject to shocks, falls or

storage with vibration or humidity, which can cause

marks on the internal races or on the balls, reducing

their useful life.

3.3.2.3

Space heater

ATTENTION

The space heaters must remain

powered

during storage to avoid moisture

condensation inside the generator and

ensure that the winding insulation resistance

remains within acceptable levels.

3.3.2.4

Insulation resistance

During the storage period, the insulation resistance of the

generator windings must be measured and recorded every

three months and before the generator installation.

Any insulation resistance reduction must be investigated.

3.3.2.5

Exposed machined surfaces

All exposed machined surfaces (e.g., shaft end and

flanges) are protected at the factory with a temporary

protective agent (rust inhibitor).

This protection coating must be reapplied every six

months or when removed and/or damaged.

Recommended Product:

Anticorit BW protective agent

Manufacturer

: Fuchs

3.3.2.6

Bearings

Depending on the machine mounting position and on the

lubrication type, the machine can be transported with or

without oil in the bearings.

The machine must be stored in its original operating

position and with oil in the bearings, when specified.

The oil level must be respected, remaining in the middle of

the sight glass.

ATTENTION

In order to keep the bearings in good

conditions during the storage period,

every

two months the shaft locking device must

be removed, and the generator rotor must

be rotated at least 10 full turns at a speed

of 30 rpm

to circulate the oil and preserve

the internal parts of the bearings.

NOTES

For bearings that have a high-pressure oil

injection system (jacking), this system must

be activated before rotating the machine

rotor.

For bearings without oil tank (dry crankcase),

the oil circulation system must be activated

before rotating the machine shaft.

The shaft must always be rotated in

the

rotation direction of the machine.

If it is not possible to rotate the machine shaft, as

recommended, after six months of storage, the following

procedure must be used for protecting both the bearing

internally and the contact surfaces against corrosion:

 Close all the threaded holes with plugs;

 Seal the gaps between the shaft and the bearing seal

on the shaft by applying water-proof adhesive tape;

 Check if all the flanges (e.g., oil inlet and outlet) are

closed. If not, they must be closed with blind covers;

 Remove the upper sight glass from the bearing and

apply the corrosion inhibitor spray (TECTYL 511 or

equivalent) inside the bearing;

 Close the bearing with the upper sight glass.

NOTES

If the bearing has no upper sight glass, the

top cover of the bearing must be

disassembled to apply the corrosion inhibitor

spray.

Each six months of storage, repeat the procedure

described above.

If the storage period exceeds two years.

 Disassemble the bearing;

 Preserve and store the parts.

3.3.2.7

Terminal box

When the insulation resistance of the generator windings

is measured, the main terminal box and the other terminal

boxes must also be inspected, observing the following

aspects:

 The inside must be dry, clean and free of dust

accumulation;

 The contact elements cannot present corrosion;

 The seals must be in proper condition;

 The cable inlets must be correctly sealed.

ATTENTION

If any of these items are not in proper

condition, proceeds the adequate

maintenance and, if necessary, replace

damaged parts.

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 17

3.3.2.8

Inspections and records during storage

The stored generator must be inspected periodically and

inspection records must be filed.

The following points must be inspected:

1. Physical damages;

2. Cleanliness;

3. Signs of water condensation;

4. Protective coating conditions;

5. Paint conditions;

6. Signs of aggressive agents;

7. Satisfactory operation of space heaters. It is

recommended that a signaling or alarm system be

installed in the location in order to detect power

interruption on the space heaters;

8. Record the ambient temperature and relative humidity

around the generator, the winding temperature (using

RTDs), the insulation resistance and the polarization

index;

9. Storage site, so that it complies with the criteria

described in section 3.3.2.1.

3.3.2.9

Maintenance plan during storage

During the storage period, the generator maintenance must be performed and recorded according to the plan described in

Table 3.1

.

Table 3.1: Storage plan

Monthly

2

months

6

months

2

years

Before

start-up

Notes

STORAGE LOCATION

Inspect the cleanliness conditions

x

Inspect the humidity and temperature

conditions

x

Check for signs of insect infestation

x

PACKAGE

Inspect for damages

x

Check the internal relative humidity

x

Change the dehumidifier in the package (if

any)

x

Whenever necessary

SPACE HEATER

Check the operating conditions

x

WHOLE GENERATOR

Perform external cleaning

x

Check the painting conditions

x

Check the rust inhibitor on the exposed

machined parts

x

Reapply the rust inhibitor

x

WINDINGS

Measure the insulation resistance

x

Measure the polarization index

x

TERMINAL BOX AND GROUNDING TERMINALS

Clean the interior of the boxes

x

Inspect the seals and gaskets

x

BEARINGS

Rotate the shaft

x

Apply anti-corrosion spray

x

Clean the bearings and relubricate them

x

Disassemble and store the parts

If the storage period exceeds 2

years

www.weg.net

18 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 13607224

3.3.3

Preparation for commissioning

3.3.3.1

Cleaning

 The internal and external parts of the generator must be

free of oil, water, dust, and dirt.

 Remove the rust inhibitor from the exposed surfaces

with a cloth damped in a petroleum-based solvent;

 Make sure that the bearings and cavities used for

lubrication are free of dirt and the cavity plugs are

correctly sealed and tightened. Oxidation and marks on

the bearing seats and on the shaft must be carefully

removed.

3.3.3.2

Bearing inspection

ATTENTION

If the generator storage period exceeds six

months, the sleeve bearings must be

disassembled, inspected and cleaned, before

starting the generator operation.

The sleeve bearings without oil tank (dry

crankcase), regardless of the generator storage

period, should necessarily be disassembled,

inspected and cleaned before starting the

generator operation.

Reassemble the sleeve bearings and carry out

lubrication.

Contact WEG to perform this procedure.

3.3.3.3

Bearing lubrication

Use the lubricant specified for bearing lubrication.

Information on the bearings and lubricants are indicated

on the bearing nameplate, and the lubrication must be

done as described in section 7.9 of this manual, always

considering the type of bearing.

3.3.3.4

Insulation resistance verification

Before putting the generator into operation, the insulation

resistance must be measured according to section 3.3.2.4

of this manual.

3.3.3.5

Others

Follow the other procedures described in section 6 of this

manual before putting the generator into operation.

www.weg.net

13607224 Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal l 19

4 INSTALLATION

4.1 INSTALLATION SITE

Generators must be installed in easily accessible places,

allowing periodic inspections, on-site maintenance and, if

necessary, removal for external services.

The following environmental conditions must be ensured:

 Clean and well-ventilated location;

 The installation of other equipment or walls must not

hinder or block the generator ventilation;

 The area around and above the generator must be

sufficient for maintenance or handling;

 The environment must be in accordance with the

generator protection degree.

4.2 SHAFT LOCK

The generator leaves the factory with a lock on the shaft to

prevent damages to the bearings during transportation.

This lock must be removed prior to generator installation.

ATTENTION

The shaft locking device must be installed

whenever the generator is removed from its

base (uncoupled) in order to prevent

damages to the bearings during

transportation.

The shaft end is protected at the factory with

a temporary protective agent (rust inhibitor).

During the generator installation, it is

necessary to remove this product from the

grounding brush (if any) contact track on the

shaft.

4.3 ROTATION DIRECTION

The rotation direction is indicated on a plate affixed to the

drive end of the generator and in the generator specific

documentation.

ATTENTION

Generators supplied with a single rotation

direction must not operate in the opposite

direction.

In order to operate the generator in the

opposite direction, consult WEG.

4.4 INSULATION RESISTANCE

4.4.1

Safety instructions

DANGER

In order to measure the insulation resistance,

the generator must be turned off and stopped.

The winding being tested must be connected

to the frame and grounded until all residual

electrostatic charges are removed. Capacitors

(if any) must also be grounded before

disconnecting and separating the terminals to

measure the insulation resistance.

Failure to comply with these procedures may

result in personal injury.

4.4.2

General considerations

When the generator is not immediately put into operation,

it must be protected against moisture, high temperatures,

and dirt, avoiding impacts to the insulation resistance.

The winding insulation resistance must be measured

before putting the generator into operation.

If the environment is too humid, the insulation resistance

must be measured periodically during storage. It is difficult

to establish fixed rules for the actual value of the winding

insulation resistance, as it varies according to the

environmental conditions (temperature, humidity),

generator cleanliness conditions (dust, oil, grease, dirt),

and quality and condition of the insulating material used.

The evaluation of the periodical follow-up records is useful

to conclude whether the generator is able to operate.

4.4.3

Measurement on the stator windings

The insulation resistance must be measured with a

megohmmeter. The testing voltage for the windings must

be in accordance with Table 4.1, and according to IEEE43

standard.

Table 4.1: Voltage for the winding Insulation resistance test

Winding rated

voltage (V)

Insulation resistance test -

continuous voltage (V)

< 1000 500

1000 - 2500 500 - 1000

2501 - 5000 1000 - 2500

5001 - 12000 2500 - 5000

> 12000 5000 - 10000

Before measuring the stator winding insulation resistance:

 Disconnect all connections to the stator terminals;

 Disconnect and insulate all CTs and PTs (if any);

 Ground the generator frame;

 Measure the winding temperature;

 Ground all temperature sensors;

 Check the humidity;

 Disconnect the neutral grounding;

 Ensure that the generator bars are not grounded.

The insulation resistance measurement of the stator

windings must be done in the main terminal box. The

instrument (megohmmeter) must be connected between

the generator frame and the winding. The frame must be

grounded and the three phases of the stator winding must

remain connected to the neutral point, as shown in Figure

4.1.

www.weg.net

20 l Installation, Operation and Maintenance Manual – Hydrogenerators – SH11 – brushless – horizontal 13607224

Figure 4.1: Megohmmeter connection

Whenever possible, each phase must be isolated and

tested separately. The separate test allows a comparison

between the phases. When a phase is tested, the other

two phases must be grounded to the same ground of the

frame, as shown in Figure 4.2.

Figure 4.2: Connection of the megohmmeter to separate phases

If the total winding measurement presents a value below

the recommended, the neutral connections must be

opened and the insulation resistance of each phase must

be measured separately.

ATTENTION

Much higher values may be frequently

obtained in generators being operated for a

long period of time. Comparison with values

obtained in previous tests on the same

generator - under similar load, temperature

and humidity conditions – may be an

excellent parameter to evaluate the winding

insulation conditions, instead of using the

value obtained in a single test as the basis.

Significant or sudden reductions are

considered suspicious.

4.4.4

Measurement on the rotor and exciter

windings

Measurement on the rotor winding:

 Disconnect the rotor cables from the diode set and

from the discharge resistor (if any);

 Connect the instrument to measure the insulation

resistance (megohmmeter) between the rotor winding

and the generator shaft. The measuring current must

not pass through the bearings.

Measurement of the main exciter stator winding:

 Disconnect the power supply cables from the exciter;

 Connect the instrument to measure the insulation

resistance (megohmmeter) between the exciter stator

winding and the generator frame.

Measurement on the main exciter rotor winding:

 Disconnect the cables of the exciter rotor from the

diode set;

 Connect the instrument to measure the insulation

r

esistance (megohmmeter) between the exciter rotor

winding and the generator shaft. The measuring current

must not pass through the bearings.

Measurement of the auxiliary exciter stator winding (PMG),

if any:

 Disconnect the cables that connect the auxiliary exciter

to the voltage regulator;

 Connect the instrument to measure the insulation

resistance (megohmmeter) between the auxiliary exciter

stator winding and the generator frame.

4.4.5

Additional Information

ATTENTION

After measuring the insulation resistance,

ground the tested winding in order to

discharge it.

The test voltage to measure the insulation

resistance of the rotor and space heater must

be 500 Vdc and for the other accessories

100 Vdc.

It is not recommended to measure the

insulation resistance of thermal protectors.

4.4.6

Polarization index

The polarization index is defined by the ratio between the

insulation resistance measured in 10 minutes and the

insulation resistance measured in 1 minute. This

measurement procedure is always carried out at relatively

constant temperatures. The polarization index allows the

evaluation of the generator insulation conditions.

DANGER

In order to avoid accidents, the winding must

be grounded immediately

after measuring the

insulation resistance.

4.4.7

Conversion of the measured values

The insulation resistance must be measured at 40°C. If the

measurement is performed at a different temperature, it is

necessary to correct the reading to 40°C by using a curve

of the insulation resistance variation as a function of the

temperature, obtained on the generator itself. If this curve

is not available, the approximate correction provided by

the curve in Figure 4.3, according to NBR 5383 / IEEE43,

may be used.

MΩ

Page is loading ...

WEG Hydrogenerators SH11 line brushless horizontal User manual

WEG Hydrogenerators SH11 line brushless horizontal User manual

Related papers

Other documents