Vista VK2-1080XIRPTZF User manual

VK2-1080XVRDPTPMF

User Manual

Before You Begin

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualiﬁed service person and should conform to local codes. This

manual provides installation and operation information. To use this document, you must have the following

minimum qualiﬁcations:

• A basic knowledge of CCTV systems and components

• A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product speciﬁcation and user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and

any other documentation provided. If you still have questions, please contact Norbain Technical Support and

Sales:

Norbain SD, 210 Wharfedale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TP, England.

UK +44 (0) 118 912 5000

Note: You should be at the equipment and ready with details before calling Technical Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following WARNING, C

AUTION and Note state-

ments identify potential hazards that can occur if the equipment is not handled proper ly:

* WARNING

Improper use of this equipment can cause severe bodily injury or equipment damage.

** CAUTION

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

This apparatus is manufactured to comply with the radio interference.

A Declaration of Conformity in accordance with the following EU standards has been made.

The manufacturer declares that the product supplied with this document is compliant the pro-

visions of the EMC Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all asso-

ciated amendments.

All lead-free products offered by the company comply with the requirements of the European

law on the Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means

our manufacture processes and products are strictly lead-free and without the hazardous sub-

stances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product

must be collected separately at the product end-of-life. This applies to your product and any

peripherals marked with this symbol. Do not dispose of these products as unsorted municipal

waste.

* This symbol indicates electrical warnings and cautions.

* This symbol indicates general warnings and cautions.

NORBAIN SD reserves the right to make changes to the product and speciﬁcation of the product from

time to time without prior notice.

WARNINGS AND CAUTIONS:

To reduce the risk of ﬁre or electric shock, do not insert any metallic objects through the ventilation grills or

other openings on the equipment.

2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

IMPORTANT SAFEGUARDS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with dry cloth.

6. Do not block any ventilation openings, Install in accordance with the manufacturer’s in-

structions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug, A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong are provided for your safety, If

the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the

obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories speciﬁed by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualiﬁed service personnel. Servicing is required when the appa-

ratus has been damaged in any way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has been dropped.

13. CAUTION − THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED

SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT

PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING IN-

STRUCTIONS UNLESS YOU QRE QUALIFIED TO DO SO.

14. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certiﬁed/Listed Class 2 power

source only.

15. ITE is to be connected only to PoE networks without routing to the outside plant.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio inter-

ference in which case the user may be required to take adequate measures.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

3

Contents

1 Introduction 5

1.1 Components .................................... 5

1.2 KeyFeatures .................................... 6

2 Installation 7

2.1 Installation ..................................... 7

2.1.1 Installation-WallMount.......................... 8

2.1.2 Installation - Ceiling Mount . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Basic Conﬁguration of Camera System . . . . . . . . . . . . . . . . . . . . . 10

2.3 Micro-SDCardInsertion.............................. 11

2.4 Connections .................................... 12

2.4.1 Network Connection & IP assignment . . . . . . . . . . . . . . . . . . 13

3 Operation 14

3.1 Accessfromabrowser .............................. 14

3.2 Accessfromtheinternet ............................. 15

3.3 Setting the admin password over a secure connection . . . . . . . . . . . . . 15

3.4 LiveViewPage................................... 16

3.5 Playback ...................................... 18

3.6 NetworkCameraSetup .............................. 20

3.6.1 BasicConﬁguration ............................ 20

3.6.2 LiveView .................................. 24

3.6.3 Video&Image ............................... 25

3.6.4 Audio .................................... 33

3.6.5 Event .................................... 35

3.6.6 DomeConﬁguration ............................ 58

3.6.7 System ................................... 67

3.7 Help ......................................... 88

3.8 Resetting to the factory default settings . . . . . . . . . . . . . . . . . . . . . 89

4 Appendix 90

4.1 Troubleshooting................................... 90

4.2 AlarmConnection ................................. 91

4.3 PreventiveMaintenance.............................. 91

4.4 ProductSpeciﬁcation................................ 92

4.5 System Requirement for Web Browser . . . . . . . . . . . . . . . . . . . . . . 94

4.6 General Performance Considerations . . . . . . . . . . . . . . . . . . . . . . 94

4

1 Introduction

The network camera supports the network service for a sensor image with progressive scan,

which can be monitored on a real-time screen regardless of distances and locations. By us-

ing its dedicated program, many users are able to have an access to the network camera

at once or a single user can monitor various network cameras at the same time. It also

enables users to play, store and retrieve a monitoring image by using a PC. All the settings

and real-time monitoring screens are also provided through an access to the web.

The network camera is fully featured for security surveillance and remote monitoring needs.

It is based on the DSP compression chip, and makes it available on the network as real-time,

full frame rate Motion JPEG and H.264 video streams.

1.1 Components

The camera is designed with compact, small size, hard dome camera housing. The housing

is constructed of aluminum, steel and plastic. The housing is designed to be mounted on

a wall or a ceiling. The housing meets the Protection Classiﬁcation IP66 standards for dust

and moisture resistance.

Dome Camera ······································· 1

Installation Guide/CD ······································· 1

Accessory Kit ······································· 1

1) Torx wrench ·················· (1)

2) 3-pin terminal block ·················· (2)

3) 6-pin terminal block ·················· (1)

5

1.2 Key Features

• Brilliant video quality

The network camera offers the highly efﬁcient H.264 video compression, which drasti-

cally reduces bandwidth and storage requirements without compromising image qual-

ity. Motion JPEG is also supported for increased ﬂexibility.

• Dual or Triple Streams

The network camera can deliver dual or triple video streams simultaneously at full

frame rate in all resolutions up to 1920 x 1080 using Motion JPEG and H.264. This

means that several video streams can be conﬁgured with different compression for-

mats, resolutions and frame rates for different needs.

• Image setting adjustment

The network camera also enables users to adjust image settings such as contrast,

brightness and saturation to improve images before encoding takes place.

• Intelligent video capabilities

The network camera includes intelligent capabilities such as enhanced video motion

detection. The network camera’s external inputs and outputs can be connected to de-

vices such as sensors and relays, enabling the system to react to alarms and activate

lights or open/close doors.

• Improved Security

The network camera logs all user access, and lists currently connected users. Also, its

full frame rate video can be provided over HTTPS.

• PoE (Power over Ethernet)

This network camera can be powered through PoE, which simpliﬁes installation since

only one cable is needed for carrying power, as well as video controls.

• ONVIF Certiﬁcate

This is a global interface standard that makes it easier for end users, integrators, con-

sultants, and manufacturers to take advantage of the possibilities offered by network

video technology. ONVIF enables interoperability between different vendor products,

increased ﬂexibility, reduced cost, and future-proof systems.

• Micro-SD Recording support

The network camera also supports a Micro-SD memory slot for local recording with

removable storage.

• Audio support

The network camera also supports two-way audio.

6

2 Installation

2.1 Installation

You need one optional mount kit of the wall mount and the ceiling mount to install.

The wall or ceiling mount must be attached to a structural object such as hard wood, con-

crete that will support the weight of the mount and dome camera.

The use of a solid backboard is recommended when attaching to gypsum walls.

1. Remove the Protection pad and the tape from attached the dome camera.

2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic

bushing. (Ceiling using the supplied M6 tapping screw and bushing)

3. Wind the both thread of the pipe end with Teﬂon tape about 20 times for sealing. Then

use a silicone rubber sealant to seal the area where the wall (ceiling) mount and the

pipe meet.

4. Place a bead of silicone sealant around the wall and ceiling mount mounting ﬂange,

press it to the surface and line up the ﬂange hole with drilled holes.

CAUTION 1: A silicone rubber sealant must be applied to seal the housing and cable-end

to secure waterprooﬁng.

CAUTION 2: When installing, a bracket must be applied.

CAUTION 3: Please reset the camera after 30 ∼ 60 minutes when installing it in situations

colder than -10

o

C.

7

2.1.1 Installation - Wall Mount

The wall mounting plate must be attached to a structural object such as concrete that will

support the weight of the mount and Dome Camera.

1. Select a suitable mounting location and verify there is sufﬁcient cable to reach the

middle of the Wall Mount.

2. Mark and drill mounting holes on the surface using the Wall Mount Flange.

3. Pull out cables required to connect to the dome camera from the wall.

4. Set and ﬁx wall mount bracket using plastic anchors and M8x35 screws.

5. Open the access plate and pull out cables through rectangular access hole of the wall

mount bracket.

6. Attach the 1.5 inch adapter to wall mount bracket and ﬁx it using set screw.

7. Attach the cameras safety wire to the wall mount bracket and organize cables.

8. Close the access plate of the wall mount bracket.

9. Push in and turn clockwise the camera into the adapter, and ﬁx it using set screw of

the adapter.

8

2.1.2 Installation - Ceiling Mount

The ceiling mounting plate must be attached to a structural object such as concrete that will

support the weight of the mount and Dome Camera.

1 Select a suitable mounting loca-

tion and verify there is sufﬁcient

cable to connect with cables from

the housing.

2 Mark and drill mounting holes on

the surface using the ceiling mount

bracket.

3 Pull out cables required to con-

nect to the dome camera from the

ceiling.

4 Attach the ceiling mount bracket

using plastic anchors and screws.

5 Attach 1.5 inch adapter to the

pipe and ﬁx it using set screw of the

adapter.

6 Pull out camera cables through

the pipe and attach the the camera

to adapter and ﬁx them using set

screw of the adapter.

7 After safety wire fo the pipe to

one of M6x35 screws of the ceiling

mount bracket.

8 Join every connectors and orga-

nize cables.

9 Lock hexagonal nut of the ceil-

ing mount bracket to ﬁx camera

attached pipe and ceiling mount

bracket.

9

2.2 Basic Conﬁguration of Camera System

No. Connector Wire Color Description

1 3-pin terminal block

RED 24VAC or 12VDC+

WHITE 24VAC or 12VDC-

2 3-pin terminal block

ORANGE HEATER & FAN

BLACK HEATER & FAN

3 6-pin terminal block

PINK ALARM INPUT 1

GRAY ALARM INPUT 2

GREEN ALARM INPUT 3

BLUE ALARM INPUT 4

BROWN GND

YELLOW ALARM OUTPUT

4 RJ-45 BLACK

Ethernet, RJ-45 port compatible with

10/100Mbps having PoE functionality.

5 STEREO GRAY AUDIO OUTPUT

6 STEREO BLACK AUDIO INPUT

The camera must be installed by qualiﬁed service personnel in accordance with all local and

federal electrical and building codes.

10

2.3 Micro-SD Card Inser tion

User can install and change Micro-SD card as shown in the following picture.

1. Open the Micro-SD card cover.

2. Install or change Micro-SD card.

3. Tightly close the Micro-SD card cover to ensure waterproofness.

11

2.4 Connections

• Connecting the Network

Connect a standard RJ-45 cable to the network port of the camera. Generally a cross-

over cable is used for directly connection to PC, while a direct cable is used for con-

nection to a hub.

• Connecting Alarms

– A1,A2,A3,A4 (Alarm Input 1,2,3,4)

You can use external devices to signal the camera to react on events. Mechanical

or electrical switches can be wired to the A1,A2,A3,A4 (Alarm Input 1,2,3,4) and

G (Ground) connectors.

– G (Ground)

NOTE: All the connectors marked G or GND are common.

Connect the ground side of the alarm input and/or alarm output to the G (Ground)

connector.

– AO (Alarm Output)

The camera can activate external devices such as buzzers or lights. Connect the

device to the AO (Alarm Output) and G (Ground) connectors.

• Connecting the Power of Camera

Connect power of 12VDC or 24VAC for the camera.

When using a 12VDC adapter, connect the positive (+) pole to the ‘ + ’ position and the

negative (-) pole to the ‘ - ’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certiﬁed/Listed Class 2 power

source only.

– Be careful not to reverse the polarity when you connect the power cable.

– You can also use a router featuring PoE (Power over Ethernet) to supply power to

the camera.

– 24VAC is recommended to use for the camera power for stable operation with

heater kit. If using PoE, the heater will not operate at all.

• Connecting the Power of Heater & Fan

Connect power of 24VAC for the camera.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certiﬁed/Listed Class 2 power

source only.

12

2.4.1 Network Connection & IP assignment

The camera supports the operation through the network. When a camera is ﬁrst connected

to the network, it is necessary to allocate an IP address to the device with the SmartManager

utility on the CD. (Default IP 192.168.30.220)

1) Connect the network camera/device to the networ k and power up.

2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager).

The main window will display, and after a short while any networ k devices connected to the

network will be displayed in the list.

3) Select the camera on the list and click right button of the mouse. You can see the pop-up

menu as below.

4) Select Assign IP Address. The Assign IP window will display. Enter the required IP ad-

dress.

NOTE: For more information, refer to the SmartManager User’s Manual.

13

3 Operation

The network camera can be used with Windows operating system and browsers. The rec-

ommended browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with

Windows.

NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow

ActiveX controls.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the network camera in the Location/Address ﬁeld

of your browser.

3. You can see a starting page. Click Live View, Playback, or Setup to enter web page.

4. The network camera’s Live View page appears in your browser.

14

3.2 Access from the internet

Once connected, the network camera is accessible on your local network (LAN). To access

the network camera from the Internet you must conﬁgure your broadband router to allow

incoming data trafﬁc to the network camera. To do this, enable the NAT traversal feature,

which will attempt to automatically conﬁgure the router to allow access to the network cam-

era. This is enabled from Setup > System > Network > NAT. For more information, please

see “System > Network > NAT” of User’s Manual.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for the default administrator user must be set.

This is done in the Admin Password dialog, which is displayed when the network camera is

accessed for the setup at the ﬁrst time. Enter your admin name and password, set by the

administrator.

NOTE: The default administrator user name and password is admin. If the password is lost,

the network camera must be reset to the factory default settings. Please see Resetting to

the factory default settings.

To prevent network eavesdropping when setting the admin password, this can be done via

an encrypted HTTPS connection, which requires an HTTPS certiﬁcate (see NOTE below).

To set the password via a standard HTTP connection, enter it directly in the ﬁrst dialog shown

below. To set the password via an encrypted HTTPS connection, please see “System > Se-

curity > HTTPS” of User’s Manual.

NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the

trafﬁc between web browsers and servers. The HTTPS certiﬁcate controls the encrypted

exchange of information.

15

3.4 Live View Page

The Live View page comes in several screen modes: 1920x1080, 1280x1024, 1280x720(960),

1024x768, 704x480(576), 640x480(360) and 320x240. Users are allowed to select the most

suitable one out of those modes. Adjust the mode in accordance with your PC speciﬁcations

and monitoring purposes.

1) General controls

Live View Page Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-

programmed video stream on the Live View page. Stream proﬁles are con-

ﬁgured under Setup > Basic Conﬁguration > Video & Image. For more

information, please see “Basic Conﬁguration > Video & Image” of User’s

Manual.

The resolution drop-down list allows you to select the most suitable one

out of video resolutions to be displayed on Live View page.

The protocol drop-down list allows you to select which combination of pro-

tocols and methods to use depending on your viewing requirements, and

on the properties of your network.

The preset drop-down list allows you to select the preset number for the

PTZ camera being used. This icon is inactivated if the PTZ settings are

not set.

16

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles

the start and stop. The Start button connects to the network camera or starts playing

a video stream.

The Pause button pauses the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be speciﬁed.

The Digital Zoom button activates a zoom-in or zoom-out function for video image on

the live screen.

The Full Screen button causes the video image to ﬁll the entire screen area. No other

windows will be visible. Press the ’Esc’ button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the

event.

The PTZ button activates a pop-up window for Pan, Tilt and Zoom control.

The VCA button shows/hides VCA rule setting and detected objects.

The Face Detector button shows/hides detected faces.

The Speaker button activates/deactivates external speaker.

The Mic button activates/deactivates microphone input.

Use this scale to control the volume of the speakers and microphones.

NOTE: VCA and Face Detection works exclusively to each other.

3) Video Streams

The network camera provides several images and video stream formats. Your require-

ments and the properties of your network will determine the type you use.

The Live View page in the network camera provides access to H.264 and Motion JPEG

video streams, and to the list of available video streams. Other applications and clients

can also access these video streams/images directly, without going via the Live View

page.

17

3.5 Playback

The Playback window contains a list of recordings made to the memory card. It shows each

recording’s start time, length, the event type used to start the recording, calendar and time

slice bar indicates if the recording is existed or not.

The description of playback window follows.

(1) Video Screen

You can see the video screen when playing the video clip in the Micro SD memory.

(2) Playback Buttons

To view a recording data in the SD local storage, select it from the list and click the

Playback buttons.

Go to the ﬁrst: go to the beginning of the video clip.

Fast backward play: fast play backward of the video clip.

Backward play: play backward of the video clip.

Step backward play: go back one frame of the video clip.

Pause: pause playback of the video clip.

Step forward play: go forward one frame of the video clip.

Forward Play: play forward the video clip.

Fast forward play: play fast forward of the video clip.

Go to the last: go to the end of the video clip.

Clip copy: copy the video clip.

Zoom In: zoom in the video clip.

Full Screen: display full screen of the video.

18

(3) Time Char t

Display an hour-based search screen for the chosen date. If there is recording data, a

blue section will be displayed on a 24-hour basis. If you select a particular hour in the

chart, a yellow square on the hour will be displayed.

(4) Speaker Control Bar

Use this scale to control the volume of the speakers.

(5) Search Calendar

Search results from the SD local storage in the network camera connected are displayed

monthly. If there is a recorded data for a particular date, a blue square on the date will be

displayed. If you select a particular date in the calendar, a yellow square on the date will

be displayed.

(6) Play Time

Displays time of the video playing.

(7) Event Search Window

Select a search option in the drop-down list and click GO button. You can also enter

the time period for searching. If you click Start Date or End Date zone, displays Search

Calendar.

(8) Event List Window

Event List displays the event(s) that were recorded in the SD local storage. Select a list

and click the play button. The video clip will be played.

19

3.6 Network Camera Setup

This section describes how to conﬁgure the network camera.

Administrator has unrestricted access to all the Setup tools, whereas Operators have access

to the settings of Basic Conﬁguration, which are Live View, Video & Image, Audio, Event,

Dome Conﬁguration, and System.

You can conﬁgure the network camera by clicking Setup either in the ﬁrst connection page

or the top second-right button of the Live View page. Accessing the network camera from a

computer for the ﬁrst time opens the Admin Password dialog box. Enter your administrator

or operator id and password to get into setup page.

NOTE: If the password is lost, the network camera must be reset to the factory default

settings. Please see “Resetting to the Factory Default Setting”.

3.6.1 Basic Conﬁguration

You can see the device information in this information page.

20

Page is loading ...

Vista VK2-1080XIRPTZF User manual

Vista VK2-1080XIRPTZF User manual

Related papers

Other documents