Altronix AL600ULX Installation guide

Category
Fire protection
Type
Installation guide
Overview:
The AL600ULX power supply converts a 115 VAC / 60Hz input, to a 12VDC or 24VDC non-power limited output, (see
specifications). The AL600ULX is UL Listed for all fire alarm, and access control applications.
Specifications:
UL listed fire and access control power supply (UL1481, UL294).
CSFM approved - California State Fire Marshal.
MEA approved - NYC Department of Buildings.
CSA approved (Canada).
NFPA 72 compliant.
Field selectable 12VDC or 24VDC non-power limited output.
Input 115VAC / 60Hz, 1.9 amp.
Maximum charge current .7 amp.
6 amps continuous supply current at 12VDC / 24VDC.
Filtered and electronically regulated output, 100mV peak output voltage ripple.
Built-in charger for sealed lead acid or gel type batteries.
Automatic switch over to stand-by battery when AC fails.
Zero voltage drop when switched over to battery backup.
AC input and DC output LED indicators.
AC fail supervision (form "C" contacts).
Low battery and battery presence supervision (form "C" contacts).
Thermal overload protection.
Short circuit protection.
Unit is complete with power supply, enclosure and cam lock.
Includes battery leads.
Enclosure Dimensions: 15.5”H x 12”W x 4.5”D
Note: Enclosure accommodates up to two (2) 12AH batteries
AL600ULX-R Enclosure Dimensions: 15.5”H x 12”W x 4.5”D
Power Supply Voltage Output Selections: *
Output Switch Position
12VDC SW 1 Closed
24VDC SW1 Open
Stand-by Specifications:
Output 4 hr. of Stand-by & 24 hr. of Stand-by & 60 hr. of Stand-by &
5 Minutes of Alarm 5 Minutes of Alarm 5 Minutes of Alarm
12VDC / 40 AH Battery Stand-by = 6.0 amps Stand-by = 1.0 amp Stand-by = 300mA
Alarm = 6.0 amps Alarm = 6.0 amps Alarm = 6.0 amps
24VDC / 12 AH Battery Stand-by = 200mA
Alarm = 6.0 amps
24VDC / 40 AH Battery Stand-by = 6.0 amps Stand-by = 1.0 amps Stand-by = 300mA
Alarm = 6.0 amps Alarm = 6.0 amps Alarm = 6.0 amps
Installation Instructions:
The AL600ULX should be installed in accordance with article 760 of The National Electrical Code or NFPA 72 as well
as all applicable Local Codes.
1. Mount the AL600ULX in desired location.
AL600ULX - UL Listed, Multi-Agency Approved
Power Supply/Charger
R
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
Rev. 091800
1
2. Set the AL600ULX to the desired DC
output voltage by setting SW1
(Fig. 1) to the appropriate position
(see power supply voltage
output selections chart).
3. Connect AC power (115VAC 50/60Hz
to terminals marked [L, G, N]
(Fig. 1). Use 18 AWG or larger for all
power connections (Battery, AC input,
DC output). Use 22 AWG to 18 AWG
for power limited circuits
(AC Fail/Low Battery reporting).
Keep power limited wiring separate
from non-power limited wiring
(115VAC / 60Hz Input, Battery
Wires). DC output Minimum .25”
spacing must be provided.
4. Connect devices to be powered to
terminals marked [--DC +] (Fig. 1).
Note: It is good operating practice to
measure and verify output voltage
before connecting devices to ensure
proper operation of equipment.
*Note: Power switch is used to turn
off DC output voltage (However if
battery is connected, its voltage will
appear on the output). It disconnects
the L (HOT) terminal from the rest of
the board. When servicing the unit,
AC mains should be removed.
5. For Access Control applications, batteries are optional. When batteries are not used,
a loss of AC will result in the loss of output voltage. When the use of stand-by batteries
is desired, they must be lead acid or gel type.
Connect battery to terminals marked [--BAT +] (Fig. 1). Use two (2) 12VDC batteries connected
in series for 24VDC operation (battery leads included).
6. It is required to connect appropriate signaling notification devices to AC FAIL & BAT FAIL (Fig. 1) supervisory
relay outputs. Use 22AWG to 18AWG wires. AC FAIL will report in 5 minutes. To delay report 6 hours cut
“AC delay” jumper.
Maintenance:
Unit should be tested at least once a year for the proper operation as follows:
Output Voltage Test: Under normal load conditions, the DC output voltage should be checked for proper voltage level
(see power supply voltage output specifications chart).
Battery Test: Under normal load conditions check that the battery is fully charged, check specified voltage both at bat-
tery terminal and at the board terminals marked [- BAT +] to insure there is no break in the battery connection wires.
Note: Maximum charging current under discharges is .7 amp.
Note: Expected battery life is 5 years, however it is recommended changing batteries in 4 years or less if needed.
+ DC ---
AL600ULXB
ALTRONIX CORP.
BKLYN, N.Y. 11220
MADE IN USA
BAT FAIL
NC C NO NC C NO
+ BAT ---
DC
24V - OPEN
12V - CLOSED
AC FAIL
L G N
OFF ON
AC
BAT
DC Output
to devices
(non power limited)
Battery and AC Supervision Circuit (power limited).
Use separate knockout. Keep 1/4" away from
non power limited wiring
CAUTION: De-energize unit prior to servicing.
For continued protection against fire hazard replace
fuse with the same type and rating 3.5A, 250V.
Replace fuse cover before energizing.
Battery 1
Battery 2
Battery connection
(non power limited)
Switch Position:
24VDC = SW1 OPEN
12VDC = SW1 CLOSED
115 power mains
(non power limited)
Door
Wire Strap
(from Enclosure to Door)
Fig. 1
2
LED Diagnostics:
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition
ON OFF Loss of AC, Stand-by battery supplying power
OFF ON No DC output
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output
Terminal Identification:
Terminal Function/Description
Legend
L, G, N Connect 115 VAC to these terminals:
L to hot, N to neutral, G to ground.
+ DC - 12VDC / 24VDC @ 6 amps continuous non-power limited output.
AC FAIL Used to notify loss of AC power, e.g. connect to audible device or alarm
C, N.C., N.O. panel. Relay normally energized when AC power is present.
Contact rating 1 amp @ 28VDC.
AC or brownout fail is reported within 1 minute of event. To delay reporting of up to
6 hrs., cut “AC delay” jumper and reset power to unit.
BAT FAIL Used to indicate low battery condition, e.g. connect to alarm panel.
N.O., N.C., C Relay normally energized when DC power is present.
Contact rating 1 amp @ 28VDC.
A removed battery is reported within 5 minutes. Battery reconnection is reported
within 1 minute.
Low battery threshold:
12VDC output threshold set @ approximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
- BAT + Stand-by battery connections. Maximum charge rate .7 amp.
3
Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
web site: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIAL600ULX - Rev. 091800
MEMBER
.875"
1"
1.3"
9.97"
13.53"
6.625"
2.25"
3.68"
4.56"
1.22"
1.22"
3.5"
1"
13.25"
2"
1.22"
12"
15.5"
4.5"
2.25"
3.68"
4.56"
1.22"
1.25"
2.2"
1"
Enclosure Dimensions:
15.5”H x 12”W x 4.5”D
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Altronix AL600ULX Installation guide

Category
Fire protection
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI