Gianni Industries PSU510 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Gianni Industries PSU510 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
PSU510 Smart Power Supplies
P-SK-PSU510-110V 2015.08.31
Output voltage 12VDC or 24VDC is field selectable by a slide switch on board. (Please turn off power and remove battery
charger connections wires before switching output voltage)
PSU510-110 Electrical Specifications:
Input Voltage: 110VAC,60Hz, 1.0Amp
Output Voltage: 12VDC nominal (13.8VDC) ; 24VDC nominal (27.6 VDC) ; Field Selectable / Filtered & Regulated
Output Current: 12VDC (Max.3A) 24VDC (Max.2A)
AC Primary Fuse Size: T1AL250V (5x20mm) Slow-Blow
Battery Fuse Size: 3AG 3.5A 250V (6x30mm)
DC Output Protection: Each output is protected by individual polyswitch (PPTC) for short circuit and overload protection
Optional Battery Pack:
Description of Operations:
If EIR option is used (eg. fire panels or smoke detectors), the output power to the lock will be interrupted due to NC, COM, NO
outputs are triggered to activate buzzer alarm. In the same time the power of board is cutoff as well.
NOTE: Turn off 110 VAC line power to power supply, using cable kit to
connect batteries as shown in figure.
24VDC-TBI
(-)1
(+)2
12V7AH
RED
BLACK
RED
BLACK
(-)1
(+)2
12VDC-TBI
12V7AH
Power Supply Board
12V or 24V
Input Terminals
Fail-safe
Battery Charger
Buzzer
Call Points
Controller
Devices
Voltage Selection
Jumper Wire
Locks
Slide Switch
Exit Buttons
Emergency Override
System Hook-Up
Dry Contacts
(Rated max. 3A/30VDC)
12 or 24 VDC
Output
Main AC Input
SLOW-BLOW Fuse
Fire Panels / Smoke Detectors
LED 1
12/24VDC
1
2
V
4
A
H
BATT
N.O. COM
COM.
N.C.
PB
PPTC
12/24VDC Output Terminals
Resistance
LED 2
12V7AH
PSU510-01
Power Distribution Board
(LED 1 red light status: Input voltage is valid)
(LED 2 green light status: Output voltage is valid)
( )
NC. COM. NO.
( )
( )
Green status LED represents DC output is valid, Red status LED represents battery charger status is normal.
The Jumper Wire in between Terminal 5 and Terminal 9 is capable to enable Terminal 5 as a ( - ) contact switch, connecting to
other devices as Electric locks.
Battery Connection for 12VDC Battery Connection for 24VDC
- Battery (Optional): Rechargeable Sealed Lead Acid
7A/Hour@12VDC
7A/Hour@24VDC(12VDCx2)
- Charging Time: Approx. 72hours - from deep discharge
WHITE
PSU510 Smart Power Supplies
P-SK-PSU510-230V 2015.08.31
PSU510-230 Electrical Specifications:
Input Voltage: 230VAC,50Hz, 1.0Amp
Output Voltage: 12VDC nominal (13.8VDC) ; 24VDC nominal (27.6 VDC) ; Field Selectable / Filtered & Regulated
DC Output Protection: Each output is protected by individual polyswitch (PPTC) for short circuit and overload protection
Optional Battery Pack:
- Battery (Optional): Rechargeable Sealed Lead Acid
Description of Operations:
NOTE: Turn off 230 VAC line power to power supply, using cable kit to
connect batteries as shown in figure.
24VDC-TBI
(-)1
(+)2
12V7AH
RED
BLACK
RED
BLACK
(-)1
(+)2
12VDC-TBI
12V7AH
Power Supply Board
12V or 24V
Input Terminals
Fail-safe
Battery Charger
Buzzer
Call Points
Controller
Devices
Voltage Selection
Jumper Wire
Locks
Slide Switch
Exit Buttons
Emergency Override
System Hook-Up
Dry Contacts
(Rated max. 3A/30VDC)
12 or 24 VDC
Output
Main AC Input
SLOW-BLOW Fuse
Fire Panels / Smoke Detectors
LED 1
12/24VDC
1
2V 4
AH
BATT
N.O. COM
COM.
N.C.
PB
PPTC
12/24VDC Output Terminals
Resistance
LED 2
12VAH
Output voltage 12VDC or 24VDC is field selectable by a slide switch on board. (Please turn off power and remove battery
charger connections wires before switching output voltage)
If EIR option is used (eg. fire panels or smoke detectors), the output power to the lock will be interrupted due to NC, COM, NO
outputs are triggered to activate buzzer alarm. In the same time the power of board is cutoff as well.
PSU510-01
Power Distribution Board
(LED 1 red light status: Input voltage is valid)
(LED 2 green light status: Output voltage is valid)
( )
NC. COM. NO.
( ) ( )
Green status LED represents DC output is valid, Red status LED represents battery charger status is normal.
The Jumper Wire in between Terminal 5 and Terminal 9 is capable to enable Terminal 5 as a ( - ) contact switch, connecting to
other devices as Electric locks.
Battery Connection for 12VDC Battery Connection for 24VDC
Output Current: 12VDC (Max.3A) 24VDC (Max.2A)
AC Primary Fuse Size: T1AL250V (5x20mm) Slow-Blow
Battery Fuse Size: 3AG 3.5A 250V (6x30mm)
7A/Hour@12VDC
7A/Hour@24VDC(12VDCx2)
- Charging Time: Approx. 72hours - from deep discharge
WHITE
/