1
Notice of Added Functionality (Ver.1.10)
Functions Added in VC-100UHD System Program Ver.1.10
5 A password must now be set to remotely control this unit via LAN.
& “Setting a Password When Connected to the Network”
5 Frame rates supporting the 2160p and 1080p output formats have been added.
& “Frame Rates Added in Support of 2160p and 1080p”
Checking the VC-100UHD System Program Version
Check the version of the VC-100UHD system program as described below.
1. Press the [SETUP] button to make the button light green.
2. Select Root menu “System”0“Information.”
The system program version is shown to the right of “Version.” If the version is lower than 1.10, an update is required.
Updating this unit
Access the website shown below to learn how to update this unit (search for product name: “VC-100UHD” 0 “Downloads” 0
“Updates & Drivers” 0 “VC-100UHD System Program (Ver.1.10)”).
http://www.roland.com/support/
Setting a Password When Connected to the Network
You must set a new password when updating the system program from a version earlier than 1.10, or when performing a
factory reset with version 1.10 or later.
NOTE
You can’t remote control this unit via LAN until the password is set.
When connecting via Telnet without setting a password, the message “Please register the password on your VC-100UHD.” is
shown.
1. Press the [SETUP] button to make the button light green.
2. Select Root menu “System”0“Network”0“Password.”
3. Set a new password.
MEMO
If you’ve forgotten the password you’ve set, you can do a factory reset, which resets the unit without a password.
Current Password
Input the current password. If the password has not been set, “None” is displayed.
In this case, you don’t need to enter a password.
New Password
Enter a new four-digit password (using the numbers 0–9 and letters A–F).
Turn the [PAGE/CURSOR] knob Move the cursor.
Turn the [VALUE] knob Change the character.
2
Notice of Added Functionality (Ver.1.10)
4. After you’ve entered the password, move the cursor to “Execute” and press the [PAGE/CURSOR] knob.
This changes the password.
“Done” The settings are complete.
“Incorrect Password” The password has not been entered correctly. Enter the password once more.
5. Make a Telnet connection from your computer via LAN.
“Enter password” is shown on the computer screen.
& “VC-100UHD Reference Manual” (“Network Connections and Settings”)
6. Follow the instructions on your computer screen and enter the password you set for the VC-100UHD.
Frame Rates Added in Support of 2160p and 1080p
1. Press the [SETUP] button to make the button light green.
2. Select Root menu “System”0“Frame Rate.”
The system frame rates of 23.98 Hz, 24 Hz, 29.97 Hz and 30 Hz have been added.
List of compatible output video formats
Processing Frame Rate (Hz)
Main Sub USB 23.98 24 29.97 30 50.00 59.94 60.00
2160pDCI 2160pDCI
( ( ( ( ( (
–
2160pUHD 2160pUHD
( ( ( ( ( (
–
1080p 1080p 1080p – –
( ( ( (
–
720p – – – –
( (
–
1080i 1080i – – – –
( (
–
4096 x 2160 DCI 4096 x 2160 DCI – – – – – –
(
3840 x 2160
UHD
3840 x 2160
UHD
– – – – – –
(
2560 x 1440 RB 2560 x 1440 RB – – – – – –
(
1920 x 1200 RB 1920 x 1200 RB – – – – – –
(
1920 x 1080
FHD
1920 x 1080
FHD
– – – – – –
(
1280 x 1024 1280 x 1024 – – – – – –
(
640 x 480 – – – – – –
(
3
Notice of Added Functionality (Ver.1.10)
MEMO
5 The value set for the frame rate is applied to the processing formats for Main Processing and Sub Processing.
5 Support for input formats is as shown below.
SDI input
The input format is determined automatically. You can check the input signal status on the status
screen.
HDMI input
Although the input format is determined automatically, you can restrict the source device output
by setting the EDID.
© 2020 Roland Corporation
01
VC-100UHD
/