Page is loading ...
Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101e
SKU: STAND-V101E
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
TOOLS NEEDED
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
A (x1)
Column
B (x1)
VESA Plate
C (x1)
Bracket
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D (x1)
Clamp
E (x1)
Grommet Base
F (x1)
Grommet Bolt
G (x1)
Support Plate
H (x2)
M6x16 Bolt
I (x4)
Rubber Pad
J (x1)
Cable Clip
K (x1)
Thumbscrew
L (x1)
4mm Allen
Wrench
M (x1)
6mm Allen
Wrench
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-B (x4)
M5x12
M-C (x4)
D5 Washer
3
ASSEMBLY STEPS
STEP 1
STEP 2
OPTION A: Clamp Installation
Assemble the column (A) to the clamp base using M6x16 bolts (H) and tighten with the 4mm Allen
wrench (L). Apply rubber pads (I) to the underside of the base.
Unscrew the handbolt on the clamp (D) to the fully open position, then remove bolts from the back
using the 4mm Allen wrench (L) to separate the clamp parts.
OPTION 1A:
Using previously removed bolts, install the clamp to the lower holes of the clamp base for desks 1” to
1-3/4” (25-45mm) in thickness.
4
STEP 2 (Continued)
STEP 3
Slide the cable clip (J) and bracket (C) down onto the column (A) to the desired height and tighten the
bracket with the 6mm Allen wrench (M).
OPTION 2A:
Using previously removed bolts, install the clamp to the upper holes of the clamp base for desks 3/8”
to 1” (10-25mm) in thickness.
OPTION B: Grommet Installation
Assemble the column (A) to the grommet base (E) using M6x16 bolts (H) and tighten with the 4mm
Allen wrench (L). Apply rubber pads (I) to the underside of the base.
Position the assembled column with base over the grommet hole in the desktop (drill hole using a 3/8”
bit if pre-drilled grommet hole not available), and install to the desktop using the grommet bolt (F)
with support plate (G). Tighten using the 6mm Allen wrench (M).
5
STEP 4
Install the VESA plate (B) to monitor using bolts (M-A or M-B) and washers (M-C).
STEP 5
Slide the VESA plate (B) with monitor onto the head of the bracket (C). Secure using the
thumbscrew (K).
6
STEP 7
Store Allen wrenches (L, M) in the cable clip (J) when not in use.
If needed, adjust tilt joint support using the 6mm Allen wrench (M). Use the cable clip (J) to organize
cables.
STEP 6
7
STEP 8
Adjust as desired.
LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/
