QOLSYS QS7134-840 Quick start guide

Brand: QOLSYS

Model: QS7134-840

Type: Quick start guide

WIRING DIAGRAM

ALT SIREN WIRING - A

ALT SIREN WIRING - B

Optional Siren Relay wiring using GND (-)

and IQ Panel 2 “EXT Siren” output*

Optional Siren Relay wiring using 12v (+)

and IQ Panel (GEN1) “Buzzer” output*

*Not intended for UL Installations

For Service Contact

COMPANY NAME:

ADDRESS:

PHONE:

ZONE LIST

SMK

Document #: IQHW16FDL

Revision Date: 5/21/19

Qolsys Part #: QS7134-840

The IQ Hardwire 16-F offers a cost effective way of integrating hardwired security &

smoke detector zones with the IQ Panel 2. It includes a large enclosure with ample

wire routing room, backup battery charging, 500mA of 12volt auxiliary power, an

onboard siren relay, built-in status LED’s for each zone and support for up to 10

two-wire smoke detectors. Normally Open and Normally Closed contacts are

supported as well as powered zones like motion sensors and glass break detectors.

Note: Not for use with CO detectors

INSTALLATION MANUAL

TECHNICAL SPECIFICATIONS

Document #: IQHW16FEQG

Revision Date: 10/7/19

Qolsys Part #: QS7134-840

ENCLOSURE OVERVIEW

Confidential &

Proprietary.

Made in Taiwan.

Page of 4 Qolsys Confidential and Proprietary.1

Input Voltage: 16.0VDC Plug-In Transformer

Backup Battery: 12VDC 5AH Max (not included)

Dimensions: 16” X 14” X 3”

Operating Temperature: 32 to 122F (0 to 50C)

EOL Supervision: 4.7k Ohm fixed or 1k-10k Ohm

depending on Resistor Mode

Input Zones: 15 N/O or N/C

Smoke Zone: 1 two-wire smoke loop, 10 detectors

max. Support for System Sensor® 2W-B, 2WT-B,

2WTA-B*

*Detector models should not be mixed

Auxiliary Voltage Output: 12VDC @ 500mA Max

Tamper Zone: Used for case tamper, no resistor

Relay Contact: 60VDC/1A Max drives siren

Compatible Control Panel: The IQ Hardwire 16-F

is for use with the Qolsys IQ Panel 2 only. Refer to

the full IQ Panel 2 installation manual for typical

installation layout, including recommended

locations of the control unit, detectors and

notification appliances.

Enclosure: For UL Installations, Qolsys enclosure

QR0073-840 shall be used.

Listed Resistor: For UL Installations, Qolsys 4.7K

Fire Resistor Part # QR0072-840 shall be used on

the 2-wire fire loop at the end of line.

Wiring: For UL Installations, recognized limited

energy cable shall be used.

UL REQUIREMENTS

INFORMATION

Tamper

Expansion

Slot

Battery Compartment

(5aH & 8aH compatible)

Locking

Screw

Optional

Cam Lock

Door

Label

Zip Tie

Rails

Knock

Outs

Expansion Battery

Compartment

ACCESSORIES

Resistors (x16)

5aH Battery

Bracket (x2)

8aH Battery

Bracket (x2)

Knock Out

Bushings (x2)

Power Supply

Battery Cables

RF Antenna (x1)

INSTALLATION MANUAL

STEP 1: INSTALL THE HARDWARE

Close, then Open the Door to

the enclosure on the IQ

Hardwire 16-F. This will

“tamper” the module and send a

learn in signal to the IQ Panel 2

STEP 2: PAIR THE IQ HARDWIRE 16 - F WITH THE IQ PANEL 2

Note: This step is required and allows the IQ Panel 2 to control the wireless Siren Relay, reset the two-wire smoke detectors after a fire event and supervise the battery,

AC power status, aux power out & tamper. The IQ Panel 2 must have the Tx/Rx 319.5 MHz SRF card installed with RF PIC 11.1.4 G2 or higher.

Press and hold “EOL LEARN”

for 1-2 secs. (all Zone LED’s

flash and then turn off)

EOL CAL LED will turn ON.

This indicates the module is

now in “Auto Learn” mode

Follow the onscreen

prompts on the IQ Panel

to finish the enrolling

process. The IQ Hardwire

16-F should be learned in

as a “Hardwire Translator”

Place your IQ Panel 2 in “Auto

Learn” mode:

Settings/Advanced Settings/

Installation/Devices/Security

Sensors/Auto Learn Sensor

Page of 4 Qolsys Confidential and Proprietary.2

1. Mount the IQ Hardwire 16-F enclosure vertically in your desired location

2. Install the provided antenna through the hole in the top of the enclosure and into the “ANT” terminal at the top of the

unit, keeping it free from obstructions

3. Wire all hardwired sensors into the terminals marked Zone 1-15. Zone 16 is reserved for two-wire smoke detectors:

a. All zones must have either a 4.7k resistor (included) or a 1k - 10k resistor installed, depending on the

which Resistor Mode is selected (see Troubleshooting on page 3), in either the N/O (parallel) or N/C

(series) position.

b. Wire the positive and negative leads from powered devices, such as motion sensors and glass break

detectors, into the “AUX” (+) and “GND” (-) terminals to power the devices.

c. The case tamper should be pre-wired from the factory and does not require a resistor. If the case

tamper is not being used, permanently shunt the zone with a piece of wire.

d. Optional: Wire the hardwired siren (60VDC/1A Max, see wiring diagram).

4. Plug in a 5Ah lead acid backup battery with included battery leads (battery not included) and secure in place with the

appropriate battery strap.

5. Using the provided 16vDC power supply, connect the leads to the terminals marked “+16.0V” & “GND”, then plug then

supply into a wall outlet. NOTE: dashed wire is positive.

RESISTOR MODES: Change between two distinct resistor modes. The default mode is “UL Mode” where 4.7k resistors are required on each zone. In

this mode the Processor LED blinks rapidly (8 times per second).

If UL installation is not required, “EOL Resistor Learning” can be enabled. In this mode the Processor LED blinks slowly (1 time per second) and any resistor

value from 1k to 10k can be used. NOTE: Zone 16 is dedicated for 2-wire smokes and requires a 4.7k resistor regardless of Resistor Mode.

To change modes, power down the unit (battery & AC), hold down “EOL LEARN” for 8 seconds while re-applying power to the device. Processor, RF Xmit

and EOL CAL LED’s will begin to flash rapidly indicating that the mode has been changed.

EOL LEARN Button: Enters and exits

“Auto Learn” mode.

MEMORY RESET Button: Clears

memory and resets the device to

factory defaults when held for 3

seconds during power up

PROCESSOR LED: Flashes during

normal operation

RF XMIT LED: Flashes when RF

transmission is being sent

EOL CAL LED: Flashes when no

zones have been learned in yet. ON

when device is in “Auto Learn” mode.

OFF when device is in “Normal

Operation Mode”

ZONES 1-15 LEDs: OFF while in

“Auto Learn” mode unless a zone has

been learned in or tripped, then ON.

OFF while in “Normal Operation

Mode” unless a zone is open, then

ON or if a zone is tampered, then

FLASHES

TROUBLESHOOTING

ZONE 16 SMOKE LED: ON when

smoke detector is in alarm

HOW TO CLEAR THE MEMORY:

Power down the unit by unplugging

the battery leads and the power

supply. Hold down “Memory Reset”

for 3 seconds while re-applying

power to the device. Processor, RF

Xmit and EOL CAL LED’s will begin to

flash rapidly indicating that the

module has been reset.

NOTE: It is recommended to Clear the

Memory when installing unit for the

first time or when switching between

Resistor Modes if devices have

previously been enrolled into the IQ

Hardwire 16

R E S I S T O R M O D E S : C h a n g e

between two distinct resistor modes.

The default mode is “UL Mode”

where 4.7k resistors are required on

each zone. In this mode the

Processor LED blinks rapidly (8 times

per second).

If UL installation is not required, “EOL

Resistor Learning” can be enabled. In

this mode the Processor LED blinks

slowly (1 time per second) and any

resistor value from 1k to 10k can be

used.

NOTE: Zone 16 is dedicated for 2-wire

smokes and requires a 4.7k resistor

regardless of Resistor Mode.

To change modes, first power down

the unit by unplugging the battery

leads and the power supply. Next

hold down “EOL LEARN” for 8

seconds while re-applying power to

the device. Processor, RF Xmit and

EOL CAL LED’s will begin to flash

rapidly indicating that the mode has

been changed

Page of 4 Qolsys Confidential and Proprietary.3

INSTALLATION MANUAL

Trip (Open/Close) each

hardwired zone one at a

time.

Two-wire smoke detectors

should be activated via the

test button on the detector

or with a can of smoke

Once all desired zones have been

learned, press the “EOL LEARN”

button to exit “Auto Learn” mode.

The EOL CAL LED will turn OFF

indicating you are no longer in

“Auto Learn” mode and all zone

LED’s will turn OFF.

When a sensor has been

tripped, the Zone LED will

illuminate and stay on until

you exit “Auto Learn” mode.

STEP 3: PAIRING INDIVIDUAL ZONES/SENSORS

Customize the sensor

type and settings as

desired. Repeat for

each zone.

The IQ Panel 2 will

“chime” indicating it

has found a new

sensor. Touch “OK”

to proceed.

Page of 4 Qolsys Confidential and Proprietary.4

WIRING DIAGRAM

ALT SIREN WIRING - A

ALT SIREN WIRING - B

Optional Siren Relay wiring using GND (-)

and IQ Panel 2 “EXT Siren” output*

Optional Siren Relay wiring using 12v (+)

and IQ Panel (GEN1) “Buzzer” output*

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux

deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute

interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.

FCC ID: 2ABBZ-RF-CHW-FIRE

IC: 11817A-RFCHWFIRE

*Not intended for UL Installations

INSTALLATION MANUAL

For Service Contact

COMPANY NAME:

ADDRESS:

PHONE:

UL 1023, UL985, ULC 1023

& ULC S545 LISTED

QOLSYS QS7134-840 Quick start guide

QOLSYS QS7134-840 Quick start guide

QOLSYS QS7134-840 Quick start guide

Related papers

Other documents