Andersen SmoothControl+ Left Hand Hydraulic Closer Installation guide

Andersen
Brand
Andersen
Model
SmoothControl+ Left Hand Hydraulic Closer
Type
Installation guide

Andersen SmoothControl+ Left Hand Hydraulic Closer allows for easy and controlled door closing. It is designed for use with Andersen® 1-1/2” Fullview Storm Doors and comes with a complete assembly for a quick and easy installation. The hydraulic closer provides smooth door operation, preventing slamming or sudden closing, ensuring a gentle and controlled closing motion. It is crafted from durable materials, ensuring longevity and reliable performance. The closer is easy to install and includes all necessary hardware for a hassle-free setup.

Andersen SmoothControl+ Left Hand Hydraulic Closer allows for easy and controlled door closing. It is designed for use with Andersen® 1-1/2” Fullview Storm Doors and comes with a complete assembly for a quick and easy installation. The hydraulic closer provides smooth door operation, preventing slamming or sudden closing, ensuring a gentle and controlled closing motion. It is crafted from durable materials, ensuring longevity and reliable performance. The closer is easy to install and includes all necessary hardware for a hassle-free setup.

1
Andersen Storm Door Division is a wholly owned subsidiary of Andersen Corporation. Andersen
Storm Door Division manufactures and supports the limited warranties for Andersen® and
EMCO® storm doors. “Andersen” and “EMCO” and all other marks where denoted are trademarks
of Andersen Corporation. ©2019 Andersen Corporation. All rights reserved.
Andersen SDD, PO Box 853
Des Moines, IA 50306-0853
06-2019 r 15043 Print in Color
p/n 902319
Replacement SmoothControl+™ Left Hand Hydraulic Closer
Assembly for Andersen® 1-1/2” Fullview Storm Doors
Installation Guide
Hydraulic Closer Arm & Bolt Assembly
Not Shown
Pink Hardware Bag
Clear Hardware Bag
PARTS OVERVIEW
B
C
A
Your installation kit should contain the following
parts. However, in some door models, not all of the
parts will be used.
A
Please Do Not Return Product to Store!
with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase.
Read this entire guide before you begin your installation. If your abilities do not
match the requirements of this installation, contact an experienced contractor.
PLEASE call the storm door Solution Center at 1-800-933-3626,
Some components may contain
sharp edges. Wear appropriate
protective equipment to avoid
potential injury.
CAUTION
SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.
RECOMMENDED TOOLS
Safety Glasses
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Work Gloves
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Major Injury / Death
Product or Property
Damage
Minor Injury
Procedure and Product
Information
This is the Safety Alert Symbol used to alert you to
potential injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
WARNING
NOTICE
CAUTION
IMPORTANT
Signal Word and Consequence
COULD
Result in:
COULD
Result in:
COULD
Result in:
Storm doors have small parts. Small parts if swallowed
could pose a choking hazard to young children. Dispose
of unused, loose, or easily removed small parts. Failure
to do so could result in injury.
WARNING
Closer is under tension and has several areas that can pinch. Use caution when
working around the closer components. Failure to do so may result in injury.
CAUTION
Hex Wrench
(provided)
Screwdrivers
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
2
REMOVE HYDRAULIC
CLOSER AND INSTALL
REPLACEMENT PART
(Left Hand)
1
d
1. With the door seated in the open position look for the hole in the top
of the hydraulic closer unit on top of the door frame. Insert the locking
pin found in the pink hardware bag into the hydraulic closer hole.
1. Close the door until the closer arm is resting against the locking pin
which will keep the door from closing fully.
1. From the interior side of the door, loosen the hydraulic closer arm
connecting bolt on the under-side of the rain cap damper assembly
using the hex wrench provided in the pink hardware bag.
NOTE: The connecting bolt is secured to the closer arm.
2. Once the connecting bolt is completely loose, pull down
slightly on the closer arm and swing the door out of the way.
1. Remove the locking pin from the top of the hydraulic closer unit by
pulling the closer arm slightly away from the door frame and lifting
locking pin from closer hole. Then carefully let the closer arm swing
back to its neutral position over the closer.
2. Using a Phillips screwdriver, remove the two unpainted screws from
the top of the hydraulic closer unit and properly dispose of the screws.
Tools recommended:
a b
c
LOCKING
PIN
LOCKING
PIN
HYDRAULIC
CLOSER HOLE
Hex Wrench
(provided)
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Screwdrivers
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Unpainted Flat
Head Screws (Qty 2)
CLEAR HARDWARE BAG
If you have a xed laminated glass 3-point lock door, go to the
steps on page 4 of this guide after completion of this step (Step D).
IMPORTANT
3
REMOVE HYDRAULIC
CLOSER AND INSTALL
REPLACEMENT PART
(continued)
1
1. Slide a at blade screwdriver between the hydraulic closer base plate
and the top of the door frame.
2. Lift up on the hydraulic closer unit with the screwdriver and slide the
unit sideways toward the hinge side of the door until it is completely
removed. Properly dispose of old hydraulic unit.
1. Install the new replacement hydraulic closer unit into the top of
the door using the reverse process of removing the old unit. When
installing the new unit, ensure the three-prong fork on the mounting
plate is pointing toward the handle side of the door frame. Also, the
middle prong must be positioned below the surface of the door frame
and the two outside prongs above the surface of the door frame.
2. Install two unpainted at head screws into the top of the hydraulic
closer unit. The screws are provided in the clear hardware bag.
1. Pull the closer arm away from door frame
towards the interior until it clears the
hydraulic closer hole, then reinstall the
locking pin into the top of the hydraulic
closer unit.
1. Open door fully and remove the locking
pin from the top of the hydraulic closer
unit.
1. Partially close the door and pull down
slightly on the closer arm to align the bolt
under the rain cap. Reconnect the hydraulic
closer arm to the rain cap damper assembly
using the provided hex wrench.
Tools recommended:
e f
g i
h
LOCKING
PIN
LOCKING
PIN
Hex Wrench
(provided)
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Screwdrivers
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Unpainted Flat
Head Screws (Qty 2)
CLEAR HARDWARE BAG
For Fixed Laminated Glass 3-Point Lock Doors, go to page 4
4
REMOVE HYDRAULIC
CLOSER AND INSTALL
REPLACEMENT PART
FOR FIXED LAMINATED
(continued)
1
1. Using a Phillips screwdriver, remove the one additional unpainted
screw from the other end of the hydraulic closer unit and properly
dispose of the screw.
2. Lift up the hydraulic closer unit straight out of door frame and properly
dispose of the hydraulic closer.
1. Install the new replacement hydraulic closer unit into the top of the
door, being careful to position it so all three screw holes align with
screw holes in door frame.
2. Install three unpainted at head screws into the top of the hydraulic
closer unit. The screws are provided in the clear hardware bag.
1. Pull the closer arm away from door frame
towards the interior until it clears the
hydraulic closer hole, then reinstall the
locking pin into the top of the hydraulic
closer unit.
1. Open door fully and remove the locking
pin from the top of the hydraulic closer
unit.
1. Partially close the door and pull down
slightly on the closer arm to align the bolt
under the rain cap. Reconnect the hydraulic
closer arm to the rain cap damper assembly
using the provided hex wrench.
Tools recommended:
e f
g i
h
LOCKING
PIN
LOCKING
PIN
Hex Wrench
(provided)
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Screwdrivers
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Unpainted Flat
Head Screws (Qty 3)
CLEAR HARDWARE BAG
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Andersen SmoothControl+ Left Hand Hydraulic Closer Installation guide

Andersen
Brand
Andersen
Model
SmoothControl+ Left Hand Hydraulic Closer
Type
Installation guide

Andersen SmoothControl+ Left Hand Hydraulic Closer allows for easy and controlled door closing. It is designed for use with Andersen® 1-1/2” Fullview Storm Doors and comes with a complete assembly for a quick and easy installation. The hydraulic closer provides smooth door operation, preventing slamming or sudden closing, ensuring a gentle and controlled closing motion. It is crafted from durable materials, ensuring longevity and reliable performance. The closer is easy to install and includes all necessary hardware for a hassle-free setup.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents