Andersen 2505930 Installation guide

Andersen
Brand
Andersen
Model
2505930
Type
Installation guide

This manual is also suitable for

Andersen
®
Patio Doors Insect Screen Installation
1
Insect Screen
For Andersen
®
Patio Doors*
W
i
n
d
o
w
s
a
i
o
D
o
o
r
s
P
t
®
Congratulations! You have just purchased one of the many fine Andersen
®
products. For ease of installation and continued enjoyment of your Andersen
®
product please read and follow this Installation Guide completely. You may direct any questions about this or other products to your local Andersen
®
dealer. Andersen
®
dealers can be found in the Yellow Pages under Windows.
Installer: Please leave the Installation Guide with the home owner to file for future reference. Thank you for choosing Andersen
®
.
1. Install Screen Panel
• Install
Screen Panel
into the door frame from the outside. Position
Screen Panel
so that bug seal is to the interior and the wider bottom
rail is to the sill. Insert top rail of screen into the screen guide of the
head jamb. The self-aligning top rollers should position themselves
on the screen track within the head screen guide. Push upwards, swing
bottom of screen panel in, and position bottom rollers on the screen
track at the sill.
A W
A
n
d
e
r
s
e
n
Andersen
INTERIOR PULL
IDENTIFICATION
PLATE
Screws
Shown Actual Size
No. 6 x 5/8"
EXTERIOR
PULL
No. 6 x 1"
HARDWARE
PACKAGE
CONTENTS
Parts Included:
Component Identification
1 - Screen Panel
Fits all standard sizes of Andersen
®
Patio Doors*
1 - Hardware Package
Interior Pull
Exterior Pull
2-No. 6 x 1" Flat Head Screws
1-Identification Plate
2-No. 6 x 5/8" Screws
This Instruction Sheet
Installation Tools Needed:
• No. 2 Phillips Head Screwdriver
• Flat Bladed Screwdriver
• Safety Glasses
NOTE: Screen latch is included with all patio door units.
WARNING
WARNING
WARNING
Weight of window and door unit(s) and
accessories will vary. Use a reasonable
number of people with sufficient strength
to lift, carry and install window and door
unit(s) and accessories. Always use
appropriate lifting techniques.
Use of ladders and/or scaffolding and
working at elevated levels may be hazard-
ous. Follow equipment manufacturer's
instructions for safe operation. Use
extreme caution when working around
window and door openings. Personal injury
and/or falls could occur.
Improper use of hand or power tools
could result in personal injury and/or
product damage. Follow equipment
manufacturer's instructions for safe
operation. Always wear safety glasses.
!
!
!
*Except 3 panel and Frenchwood Outswing Patio Doors
Copyright © 1995 Andersen
®
Corporation, Bayport, Minnesota 55003 Instruction Sheet # 0001666 Revised 03/23/01
Andersen
®
Patio Doors
Insect Screen Installation
2
ADJUSTING
SCREW
4. Check Screen Panel Operation
• Install
Interior and Exterior Pulls,
through pre-drilled holes
corresponding with the adjacent door lock. Secure
Interior and
Exterior Pulls
with the two No. 6 x 1" flat head screws provided.
Do not overtighten.
A
ndersen
Fig. 2
3. Remove Screen Panel
AW
Interior
Pull
Exterior
Pull
• Check
Screen Panel
operation. Insure that rollers are properly
seated on track and
Screen Panel
is level. If bottom appears to
be unlevel or dragging, insert a screwdriver into adjusting holes
on screen and turn screw to raise or lower
Screen Panel
.
• Remove
Screen Panel
from door frame. Attach
Identification
Plate
to the exterior of the screen (on the side opposite the
pulls.) Using two No. 6 x 5/8" screws provided. Do not
overtighten. Replace screen panel into door frame.
2. Install Pulls
  • Page 1 1
  • Page 2 2

Andersen 2505930 Installation guide

Andersen
Brand
Andersen
Model
2505930
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents