2. APAC Opto Electronics
  3. AO-1210
AO-1210

APAC Opto Electronics AO-1210 Quick User Manual

  • Hello! I am an AI chatbot trained to assist you with the APAC Opto Electronics AO-1210 Quick User Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is AO-1210?
    How does AO-1210 assign IP addresses to ZigBee devices?
    Is any additional header field required for data transmission?
    How can I connect AO-1210 to the host PC?
    What is the default IP address of the AO-1210?
    How can I change the parameters of AO-1210?
    What is the command format for ZigBee settings?
    What are the default ZigBee settings?
    What is the serial interface of AO-1210?
    What is the power consumption of AO-1210?
APAC Opto Electronics Inc.
AO-1210 LAN to ZigBee Converter
Quick User Manual
AO-1210 LAN to ZigBee Converter User Manual
Page 1 of 5
Version 1.0
Date:2012/7/25
APAC Opto Electronics Inc.
3 Tzu Chiang Road, Hsinchu Industrial Park
Hukow, Hsinchu Hsien, Taiwan 303
TEL: +886-3-5986799
FAX: +886-3-5986655
Website: www.apacoe.com.tw
1. Introduction
AO-1210 is an embedded Internet/Ethernet controller suitable for embedded wireless
control applications. This converter can perform conversion from Addressable Ethernet to
ZigBee 2007 Pro standard.
Most ZigBee devices do not support device addresses over the Internet. The AO-1210
can assign a static IP or dynamic IP address from the DHCP sever to any ZigBee device
installed in the Ethernet network. Characteristically, AO-1210 is a transparent device which
does not require any extra header field appended to transmitted data. For example, when
Host-PC sends data to the destination AO-1210 via Ethernet network, the ZigBee interface
of AO-1210 will receive the same data.
2. Wiring
There are 2 approaches to connect AO-1210 and the host PC.
1. Use the “Cross Over” CAT-5 cable to link AO-1210 and the Host PC directly, as shown
below.
2. Connect AO-1210 and the Host PC though an Ethernet HUB, as shown below.
Host PC
AO
-
12
10
Repearter
)
LAN to ZigBee
AO
-
12
10
Repearter
)
LAN to ZigBee
Ethernet
HUB
AO
-
1503
#1
(Router)
AO
-
1503
#
2
(Router)
AO
-
1503
#
3
(Router)
Host PC
AO-1210
LAN to ZigBee
CAT-5 Cross Over
AO-1210 LAN to ZigBee Converter User Manual
Page 2 of 5
Version 1.0
Date:2012/7/25
APAC Opto Electronics Inc.
3 Tzu Chiang Road, Hsinchu Industrial Park
Hukow, Hsinchu Hsien, Taiwan 303
TEL: +886-3-5986799
FAX: +886-3-5986655
Website: www.apacoe.com.tw
3. Quick Start
3.1 LAN Settings
AO-1210 has a built-in web server, users can change all internal parameter setting by
browser interface. The default IP address is 192.168.0.1.
To set the parameters, users can use any browser and open the URL
(http://192.168.0.1/setting.htm). These parameters include serial and network settings as
illustrated in the following figure.
When the parameter setting is completed, just press the “Apply” button, then new
parameters will be saved and the AO-1210 will reboot.
The main page provides two essential functions,
(1) Apply: to update all parameters.
(2) Reset: to reset the configuration value to the default settings produced by the
manufacturer.
Notice: Don’t press the “Firmware Update” button.
AO-1210 LAN to ZigBee Converter User Manual
Page 3 of 5
Version 1.0
Date:2012/7/25
APAC Opto Electronics Inc.
3 Tzu Chiang Road, Hsinchu Industrial Park
Hukow, Hsinchu Hsien, Taiwan 303
TEL: +886-3-5986799
FAX: +886-3-5986655
Website: www.apacoe.com.tw
3.2 ZigBee Settings (New)
(1) Format Representation: note that commands are all uppercase ASCII code.
///x NNNN PPPP ChPo
(2) Description:
///x ///: Start command,
x = R set to ROUTER,
x = C set to Coordinator
NNNN: Node ID, ex: 1234 (i.e., 0x1234)
Router: range from 0001 to EFFF (Hex representation)
Coordinator: fixed to 0000 (Hex representation)
PPPP: PAN ID, range 0000 to EFFF (Hex representation)
ChPo: set channel and output power
Ch: range from 11 to 26 (Dec representation)
Po: range from 0 to 16 (Dec representation)
Value
OutPower Value
OutPower Value
OutPower Value
OutPower
00 4.5dBm 04 -1.5 dBm 08 -8 dBm 12
-16 dBm
01 2.5 dBm 05 -3 dBm 09 -10 dBm 13
-18 dBm
02 1 dBm 06 -4 dBm 10 -12 dBm 14
-20 dBm
03 -0.5 dBm 07 -6 dBm 11 -14 dBm 15
-22 dBm
(3) Examples:
///R000100202600
Router, NID=0001, PID=0020, 26 channel, TX output power 4.5dBm.
///C000000202600
Coordinator, NID=0000, PID=0020, 26 channel, TX output power 4.5dBm.
Query command: ///?
HOST sends “///?” to query AO-1210 ZigBee setting status
AO-1210 responses ///xNNNNPPPPChPo (refer to (2) format description)
Send command: received unspecified NID, i.e., data broadcast mode
specify received NID
Format :NNNNddddddd (at most 60 bytes)
Ex
:0243hallo_world!
AO-1210 LAN to ZigBee Converter User Manual
Page 4 of 5
Version 1.0
Date:2012/7/25
APAC Opto Electronics Inc.
3 Tzu Chiang Road, Hsinchu Industrial Park
Hukow, Hsinchu Hsien, Taiwan 303
TEL: +886-3-5986799
FAX: +886-3-5986655
Website: www.apacoe.com.tw
Assign NODE ID=0x0243 Route to receive data “hallo_world!”
3.3 ZigBee Settings (AT command): please refer to AO-1503 user manual.
4. Hardware Features
Serial Interface
Interface: UART compatibility.
Data Rate: 9600 bps.
Characters: 8.
Parity: None
Stop Bits: 1.
Ethernet Interface
Ethernet Interface: 10Base-T, 100Base-TX.
Ethernet Speed/Duplex: Auto-negotiation 10/100Mbps, Full/Half duplex.
Protocols Supported: ARP, IP, UDP, TCP, BootP.
Network Services: DHCP, DNS, PPPoE, TFTP, HTTP, UDP Broadcasting.
Auto-MDIX: Yes.
Electronic Character
DC Power Consumption: DV5V /350mA(max).
Operation Temperature: 0~65℃.
Operation Humidity: 0~85%RH.
Storage Temperature: -20~85℃.
/