Magnetek Flex Wave™ Owner's manual

Type
Owner's manual

This manual is also suitable for

Flex Wave™
Radio Remote Control
Technical Manual
Part Number: 191-50000-M200 R00
April 2021
©Copyright 2021 Magnetek
Flex Wave Technical Manual
April 2021
Page 2 of 96
SERVICE INFORMATION
For questions regarding service or technical information contact:
1.866.MAG.SERV
(1.866.624.7378)
International Service
Outside the U.S. and Canada call +1.262.783.3500, press 3.
Columbus McKinnon Corporation Locations
Magnetek
N49 W13650 Campbell Drive
Menomonee Falls, WI 53051
Telephone: 800.288.8178
E-mail: field.service@magnetek.com
Fax Numbers:
Main: 800.298.3503
Sales: 262.783.3510
Service: 262.783.3508
Canada
161 Orenda Road
Unit 1
Brampton, Ontario
L6W 1W3 Canada
Telephone: 800.792.7253
Fax: 905.828.5707
416.424.7617 (24/7 Service pager)
United Kingdom
Telephone: +44 (0) 1675 437297
Germany
STAHL CraneSystems GmbH
Telephone: +49 7940 128-0
Website
https://www.columbusmckinnon.com/magnetek
© 2021 Columbus McKinnon Corporation
All rights reserved. This notice applies to all copyrighted materials included with this product, including, but not
limited to, this manual and software embodied within the product. This manual is intended for the sole use of the
person(s) to whom it was provided, and any unauthorized distribution of the manual or dispersal of its contents is
strictly forbidden. This manual may not be reproduced in whole or in part by any means whatsoever without the
expressed written permission of the Columbus McKinnon Corporation.
Flex Wave Technical Manual
April 2021
Page 3 of 96
PRODUCT SAFETY INFORMATION
Magnetek, Inc. offers a broad range of radio remote control products, control products, adjustable frequency drives,
and industrial braking systems for overhead material handling applications. This manual has been prepared by
Magnetek to provide information and recommendations for the installation, use, operation and service of Magnetek’s
material handling products and systems (Magnetek Products). Anyone who uses, operates, maintains, services,
installs, or owns Magnetek Products should know, understand, and follow the instructions and safety
recommendations in this manual for Magnetek Products.
The recommendations in this manual do not take precedence over any of the following requirements relating to
cranes, hoists and lifting devices:
Instructions, manuals, and safety warnings of the manufacturers of the equipment where the radio system
is used,
Plant safety rules and procedures of the employers and the owners of facilities where the Magnetek
Products are being used,
Applicable local, state/provincial or federal codes (e.g., OSHA), ordinances, standards, and requirements,
or
Safety standards and practices for the overhead material handling industry.
National and international directives and regulations must be observed for erection, commissioning,
operation, and periodic tests, in particular the Machinery Directive 2006/42/EC, the directive for the use of
work equipment 89/655/EEC, safety regulations and relevant national safety regulations.
This manual does not include or address the specific instructions and safety warnings of the equipment
manufacturers or any of the other requirements listed above. It is the responsibility of the owners, users, and
operators of the Magnetek Products to know, understand and follow all of these requirements. It is the
responsibility of the owner of the Magnetek Products to make its employees aware of all of the above listed
requirements and to make certain that all operators are properly trained. No one should use Magnetek Products
prior to becoming familiar with and being trained in these requirements.
WARRANTY INFORMATION
FOR INFORMATION ON MAGNETEK’S PRODUCT WARRANTIES BY PRODUCT TYPE, PLEASE VISIT
WWW.COLUMBUSMCKINNON.COM/MAGNETEK.
Flex Wave Technical Manual
April 2021
Page 4 of 96
Table of Contents
1 Introduction...................................................................................................................................................... 6
2 Radio Controlled Safety.................................................................................................................................. 7
2.1 Critical Installation Considerations ............................................................................................................... 8
2.2 General......................................................................................................................................................... 8
2.3 Persons Authorized to Operate Radio Controlled Cranes............................................................................ 8
2.4 Safety Information and Recommended Training for Radio Controlled Equipment Operators...................... 9
2.5 Transmitter Unit.......................................................................................................................................... 10
2.6 Pre-Operation Test..................................................................................................................................... 10
2.7 Batteries ..................................................................................................................................................... 11
2.7.1 Changing Batteries ............................................................................................................................. 11
2.7.2 Battery Charging................................................................................................................................. 11
3 General System Information......................................................................................................................... 12
3.1 General Operation...................................................................................................................................... 12
3.2 Transmitter ................................................................................................................................................. 14
3.2.1 External Illustrations ........................................................................................................................... 14
3.2.2 Internal Illustrations ............................................................................................................................ 15
3.3 Receiver ..................................................................................................................................................... 16
3.3.1 4Wave Receiver ................................................................................................................................. 16
3.3.2 6Wave Receiver ................................................................................................................................. 18
3.3.3 8Wave Receiver ................................................................................................................................. 20
3.3.4 12Wave Receiver ............................................................................................................................... 22
3.3.5 4Wave-MRX and 6Wave-MRX........................................................................................................... 24
4 Function Settings .......................................................................................................................................... 26
4.1 Transmitter ................................................................................................................................................. 26
4.1.1 Transmitter Firmware Version ............................................................................................................ 26
4.1.2 Display Frequency Band .................................................................................................................... 26
4.1.3 Transmitter Channel Settings ............................................................................................................. 27
4.1.4 Remote Pairing................................................................................................................................... 29
4.1.5 I-Chip .................................................................................................................................................. 31
4.1.6 Transmitter Output Power Settings .................................................................................................... 32
4.1.7 Transmitter Inactivity Timer Settings .................................................................................................. 33
4.1.8 Zero-G Sensor Settings...................................................................................................................... 33
4.1.9 Transmitter Start Function Settings .................................................................................................... 34
4.1.10 Infrared Programming......................................................................................................................... 34
4.1.11 Output Feedback Settings .................................................................................................................. 34
4.1.12 Pushbutton Function Settings............................................................................................................. 34
4.2 Receiver ..................................................................................................................................................... 53
4.2.1 Receiver Channel Settings ................................................................................................................. 53
4.2.2 Output Relay Configurations .............................................................................................................. 54
4.2.3 Dipswitch Settings .............................................................................................................................. 59
4.2.4 Jumper Settings.................................................................................................................................. 66
4.2.5 Fuse Ratings – 4/6Wave only............................................................................................................. 69
4.2.6 Voltage Settings – 8/12Wave only...................................................................................................... 69
4.2.7 Horn Installation.................................................................................................................................. 70
4.2.8 Indicator Light and Buzzer Installation on the MRX............................................................................ 70
4.2.9 Other Function Output Relays Settings .............................................................................................. 71
4.2.10 System Channels Table ..................................................................................................................... 72
5 Receiver Installation...................................................................................................................................... 76
5.1 Pre-installation Precautions........................................................................................................................ 76
5.2 Step-by-Step Installation ............................................................................................................................ 77
6 System Status Light Indications .................................................................................................................. 80
6.1 Transmitter Status Indications.................................................................................................................... 80
6.2 Receiver Status Indications........................................................................................................................ 81
6.3 Receiver Power Indications........................................................................................................................ 81
6.4 Receiver COM Indications.......................................................................................................................... 81
Flex Wave Technical Manual
April 2021
Page 5 of 96
7 General Specifications.................................................................................................................................. 82
Appendix A Tandem Systems.............................................................................................................................. 83
Apx A1.Tandem System Operation..................................................................................................................... 83
Apx A2.Tandem System Operation..................................................................................................................... 84
Apx A3.Tandem System Configurations ............................................................................................................. 85
Appendix B Receiver Select Radio Systems (RS).............................................................................................. 86
General Operation............................................................................................................................................... 86
Apx B1. RS System Types ............................................................................................................................ 86
Apx B2. I-Chip Settings ................................................................................................................................. 90
Apx B3. Transmitter Types ............................................................................................................................ 91
Apx B4. RS Transmitter Settings .................................................................................................................. 92
Apx B5. RS Receiver Settings....................................................................................................................... 93
Apx B6. Flex Wave RS Wiring Diagram ........................................................................................................ 94
Flex Wave Technical Manual
April 2021
Page 6 of 96
1 Introduction
The Flex Wave radio remote control systems are designed for control of industrial equipment and machinery such
as overhead traveling cranes, jib cranes, gantry cranes, tower cranes, electric hoists, winches, monorails,
conveyor belts, mining equipment and other material handling equipment where wireless control is preferred.
Each Flex Wave system consists of two transmitter handsets paired with one or more receiver unit(s). Other
standard-equipped accessories include transmitter waist belt, spare transmitter power key, vinyl pouch, “AA”
alkaline batteries, pushbutton labels, LED labels, output cable, and instruction manuals / CD.
List of notable features includes:
Advanced Controls – the system utilizes dual advanced microprocessor controls with 32-bit CRC and
Hamming Code, providing ultra-fast, safe, precise, and error-free encoding and decoding.
Frequency Agile RF Transceiver – the system automatically searches and locks onto a free and
uninterrupted channel at every system startup or during operation when encountering radio interference. The
system is also capable of two-way communication between the transmitter and receiver as well as receiver-to-
receiver with system status and relay output feedbacks.
Zero-G Sensor Embedded – the transmitter is embedded with a Zero-G sensor to guard against any
unintended control of the crane or equipment when transmitter is thrown or dropped.
Wireless Remote Pairing Function – system information can be transferred wirelessly between two
transmitters or between a transmitter and a receiver without the hassle of resetting the spares.
Reliable Pushbuttons – the pushbuttons have gold-plated contacts and are rated for more than
2 million press cycles. The defined snap-action steps provide positive tactile feedback even through gloves.
Low Power Consumption – requires only two “AA” alkaline batteries for more than 100 hours of uninterrupted
operation between replacements.
Durable Nylon and Fiberglass Composite Enclosures – highly resistant to breakage and deformation even
in the most abusive environments. The receiver enclosures and output cables are IEC60332-1-2 specified. The
transmitter and receiver enclosures are IP66 rated.
Full Compliance – all systems fully comply with the FCC Part: 15 Rules, IC-RSS-210 and European Safety
Standards (CE mark). For a full list of compliance please contact the manufacturer for details.
Optional Accessories – Transmitter belt clip, transmitter lanyard, transmitter rubber guard, buzzer, charging
station, multiple receivers function, and many others.
Flex Wave Technical Manual
April 2021
Page 7 of 96
2 Radio Controlled Safety
WARNINGS and CAUTIONS
Throughout this document WARNING and CAUTION statements have been deliberately placed to
highlight items critical to the protection of personnel and equipment.
NOTE: A NOTE statement is used to notify people of installation, operation, programming, or maintenance
information that is important, but not hazard-related.
WARNINGS and CAUTIONS SHOULD NEVER BE DISREGARDED.
The safety rules in this section are not intended to replace any rules or regulations of any applicable local, state, or federal
governing organizations. Always follow your local lockout and tagout procedure when maintaining any radio equipment. The
following information is intended to be used in conjunction with other rules or regulations already in existence. It is important to
read all of the safety information contained in this section before installing or operating the Radio Control System.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate
injury. It may also be used to alert against unsafe practices.
Flex Wave Technical Manual
April 2021
Page 8 of 96
2.1 Critical Installation Considerations
2.2 General
Radio controlled material handling equipment operates in several directions. Cranes, hoists, lifting devices and
other material handling equipment can be large, and can operate at high speeds. The equipment is often operated
in areas where people are working in close proximity to the material handling equipment. The operator must
exercise extreme caution at all times. Workers must constantly be alert to avoid accidents. The following
recommendations have been included to indicate how careful and thoughtful actions may prevent injuries, prevent
damage to equipment, or even save a life.
2.3 Persons Authorized to Operate Radio Controlled Cranes
Only properly trained persons designated by management should be permitted to operate radio controlled
equipment.
Radio controlled cranes, hoists, lifting devices and other material handling equipment should not be operated by
any person who cannot read or understand signs, notices and operating instructions that pertain to the equipment.
WARNING
Prior to installation and operation of this equipment, read and develop an understanding of the contents of this
manual and the operation manual of the equipment or device to which this equipment will be interfaced. Failure
to follow this warning could result in serious injury or death and damage to equipment.
All equipment must have a mainline contactor installed and all tracked cranes, hoists, lifting devices and similar
equipment must have a brake installed. Failure to follow this warning could result in serious injury or death and
damage to equipment.
An audible and/or visual warning means must be provided on all remote controlled equipment as required by
code, regulation, or industry standard. These audible and/or visual warning devices must meet all
governmental requirements. Failure to follow this warning could result in serious injury or death and damage to
equipment.
Follow your local lockout tagout procedure before maintaining any remote controlled equipment. Always
remove all electrical power from the crane, hoist, lifting device or similar equipment before attempting any
installation procedures. De-energize and tagout all sources of electrical power before touch-testing any
equipment. Failure to follow this warning could result in serious injury or death and damage to equipment.
The direct outputs of this product are not designed to interface directly to two state safety critical maintained
functions, i.e., magnets, vacuum lifts, pumps, emergency equipment, etc. A mechanically locking intermediate
relay system with separate power considerations must be provided. Failure to follow this warning could result
in serious injury or death or damage to equipment.
Flex Wave Technical Manual
April 2021
Page 9 of 96
Radio controlled equipment should not be operated by any person with insufficient eyesight or hearing or by any
person who may be suffering from a disorder or illness that may cause them to lose control of the equipment, is
taking any medication that may cause loss of equipment control, or is under the influence of alcohol or drugs.
2.4 Safety Information and Recommended Training for Radio
Controlled Equipment Operators
Anyone being trained to operate radio controlled equipment should possess as a minimum the following
knowledge and skills before using the radio controlled equipment.
The operator should:
have knowledge of hazards pertaining to equipment operation
have knowledge of safety rules for radio controlled equipment
have the ability to judge distance of moving objects
know how to properly test prior to operation
be trained in the safe operation of the radio transmitter as it pertains to the crane, hoist, lifting device or other
material handling equipment being operated
have knowledge of the use of equipment warning lights and alarms
have knowledge of the proper storage space for a radio control transmitter when not in use
be trained in transferring a radio control transmitter to another person
be trained how and when to report unsafe or unusual operating conditions
test the transmitter emergency stop and all warning devices prior to operation; testing should be done on each
shift, without a load
be thoroughly trained and knowledgeable in proper and safe operation of the crane, hoist, lifting device, or
other material handling equipment that utilizes the radio control
know how to keep the operator and other people clear of lifted loads and to avoid “pinch” points
continuously watch and monitor status of lifted loads
know and follow cable and hook inspection procedures
know and follow the local lockout and tagout procedures when servicing radio controlled equipment
know and follow all applicable operating and maintenance manuals, safety procedures, regulatory
requirements, and industry standards and codes
The operator shall not:
lift or move more than the rated load
operate the material handling equipment if the direction of travel or function engaged does not agree with what
is indicated on the controller
use the crane, hoist or lifting device to lift, support or transport people
lift or carry any loads over people
operate the crane, hoist or lifting device unless all persons, including the operator, are and remain clear of the
supported load and any potential pinch points
operate a crane, hoist or lifting device when the device is not centered over the load
operate a crane, hoist or lifting device if the chain or wire rope is not seated properly in the sprockets, drum or
sheave
operate any damaged or malfunctioning crane, hoist, lifting device or other material handling equipment
change any settings or controls without authorization and proper training
remove or obscure any warning or safety labels or tags
leave any load unattended while lifted
leave power on the radio controlled equipment when the equipment is not in operation
operate any material handling equipment using a damaged controller because the unit may be unsafe
operate manual motions with other than manual power
operate radio controlled equipment when low battery indicator is on
Flex Wave Technical Manual
April 2021
Page 10 of 96
2.5 Transmitter Unit
Transmitter switches should never be mechanically blocked on or off. When not in use, the operator should turn the
transmitter off. A secure storage space should be provided for the transmitter unit, and the transmitter unit should
always be placed there when not in use. This precaution will help prevent unauthorized people from operating the
material handling equipment.
Spare transmitters should be stored in a secure storage space and only removed from the storage space after the
current transmitter in use has been turned off, taken out of the service area and secured.
2.6 Pre-Operation Test
At the start of each work shift, or when a new operator takes control of the crane, operators should
perform, at a minimum, the following steps before making lifts with any crane or hoist:
Test all warning devices.
Test all direction and speed controls.
Test the transmitter emergency stop.
WARNING
The operator should not attempt to repair any radio controller. If any product performance or safety concerns
are observed, the equipment should immediately be taken out of service and be reported to the supervisor.
Damaged and inoperable radio controller equipment should be returned to Magnetek for evaluation and repair.
Failure to follow this warning could result in serious injury or death and damage to equipment.
Flex Wave Technical Manual
April 2021
Page 11 of 96
2.7 Batteries
2.7.1 Changing Batteries
Change transmitter batteries (“AA” alkaline battery x 2) by unscrewing the battery cover located on the backside of
the transmitter. During battery installation make sure the batteries are installed correctly, with “+” to “+” charge and
“-” to “-” charge. Also make sure the screw is tightened after battery installation to avoid water, moisture, dirt,
grease, and other liquid penetration.
2.7.2 Battery Charging
The transmitter is designed to accept any off-the-shelf NiMH rechargeable batteries.
When charging both transmitter and individual batteries at the same time the priority
always goes to the transmitter charging. The individual battery charging begins only
after the transmitter charging is completed. Depending on the battery capacity the
average charging time is approximately 3 hours from completely drained to fully
charged. Solid red on the LED represents charging in progress, solid green represents
batteries fully charged, and LED off represents no batteries detected.
NOTE: Do not use any rechargeable lithium ion batteries as they will damage both the
transmitter and the charging station.
WARNING
Know and follow proper battery handling, charging and disposal procedures. Improper battery procedures can
cause batteries to explode or do other serious damage. Failure to follow this warning could result in serious
injury or death and damage to equipment.
Flex Wave Technical Manual
April 2021
Page 12 of 96
3 General System Information
3.1 General Operation
1. Reset the STOP button located on the top left hand corner of the transmitter by rotating it clockwise or
counterclockwise; the button will pop up. Turn on the transmitter power by inserting the power switch key and
rotating to the ON ( I ) position.
2. After turning on the transmitter power, check the Status LED on the transmitter for any sign of system
irregularities (see Section 6.1 Transmitter Status Indications on page 80). If the transmitter is in good
working order the Status LED will display solid green for up to 2 seconds at power on (no faults detected).
3. Rotate the power switch key further to the START position and hold it there for up to 2 seconds (Status LED
solid green). When the receiver MAIN relays are activated the Status LED will change from solid green to solid
orange (system on). The power switch key will retract back to the ON ( I ) position when released. The same
START position becomes an auxiliary function thereafter (see Section 4.2.2.3 START + AUX Function on
page 56). Once the MAIN relays are closed by a successful start, the system is active for operation. Press any
pushbutton on the transmitter to begin operation. Pressing any pushbutton before executing the START
command at system startup will result in no signals transmitted (Status LED blinks orange).
4. Press any pushbutton on the transmitter to begin operation. During transmitter inactivity (pushbuttons not
pressed), the transmitter will automatically switch to standby mode, with an orange blink on the Status LED at
4-second intervals. Always turn off the transmitter power by turning the key switch to the OFF position, when
not in use to save battery power.
5. In case of an emergency, press down the STOP button to disconnect the receiver MAIN relays and the
transmitter power. To resume operation, rotate the STOP button clockwise or counterclockwise; the button will
pop up. Then rotate the power key to the START position to reconnect the receiver MAIN relays. For safety,
executing the START command is required every time the transmitter is turned on or after every STOP button
reset.
NOTE: Pushing the STOP button does not turn off the transmitter power and it will continue to draw battery power.
The only way to turn the transmitter off and stop battery draw is to turn the key switch to the OFF position.
Flex Wave Technical Manual
April 2021
Page 13 of 96
6. After 5 minutes of inactivity (pushbutton not pressed) the receiver MAIN relays are temporarily disconnected
(see Section 4.1.7 Transmitter Inactivity Timer Settings on page 33). Press any pushbutton or execute the
START command to resume operation (see Section 4.1.9 Transmitter Start Function Settings on page 34).
The receiver MAIN relays are also temporarily disconnected when the system encounters strong radio
interference, dead spots, low battery condition, and system out of operating range.
7. Turn off the transmitter power by rotating the power switch key counterclockwise to the OFF ( 0 ) position; it will
disconnect the transmitter power and the receiver MAIN relays altogether. Turn it further counterclockwise to
release the key.
Flex Wave Technical Manual
April 2021
Page 14 of 96
3.2 Transmitter
3.2.1 External Illustrations
NOTE: Flex 8Wave-AB, 8Wave-T, Flex 12Wave-AB, and 12Wave-T models have the A/B/A+B rotary switch on
PB8 (8Wave) or PB12 (12Wave) slot.
1. STOP Button
2. Power Key Switch
3. Status LED Indicator
4. Pushbutton 1 (PB1)
5. Pushbutton 2 (PB2)
6. Pushbutton 3 (PB3)
7. Pushbutton 4 (PB4)
8. Pushbutton 5 (PB5)
9. Pushbutton 6 (PB6)
10. Pushbutton 7 (PB7)
11. Pushbutton 8 (PB8)
12. Pushbutton 9 (PB9)
13. Pushbutton 10 (PB10)
14. Pushbutton 11 (PB11)
15. Pushbutton 12 (PB12)
16. TAC* and Inductive Charging
Slot (Future Feature)
17. Battery Cover Screw
18. System Information
19. Lanyard and Waist Belt
Attachment Slot
1
3
5
7
2
4
6
1
3
5
7
9
2
4
6
8
1
3
5
7
9
11
2
4
6
8
10
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
17
18
19
4-Button Front
6-Button Front
8-Button Front
12-Button Front
12-Button Back
Flex Wave Technical Manual
April 2021
Page 15 of 96
3.2.2 Internal Illustrations
* The programming port is only used for updating the transmitter firmware. It is not used with the infrared (IR)
programmer. For more information, contact Magnetek field service.
NOTE: Flex 8Wave-AB, 8Wave-T, Flex 12Wave-AB, and 12Wave-T models have the A/B/A+B rotary switch on
PBB PB8 (8Wave) or PB12 (12Wave) slot.
1. RF Transceiver Board 5. Infrared Sensors
2. Encoder Board 6. I-Chip Slot
3. Status LED Indicator 7. Function Dipswitch
4. A/B/C/D LED Indicators 8. Programming Port*
3
1
3
5
2
4
6
1
5
2
4
6
1
3
5
2
4
6
1
3
5
2
4
6
8
7
4-Button Top
6-Button Top
8-Button Top
12-Button Top
12-Button Back
Flex Wave Technical Manual
April 2021
Page 16 of 96
3.3 Receiver
3.3.1 4Wave Receiver
3.3.1.1 External and Internal Illustrations
1. External RP-TNC Antenna Port
a
a NOTE:
The GEN1 Flex EX receiver used a TNC antenna connection, whereas the GEN2 Flex Wave receiver uses an RP-TNC
antenna connection. Make sure the antenna you are using has the correct connection to avoid damaging the antenna connection.
11. Mounting Bracket Release
2. COM LED Indicator 12. Decoder Board
3. Status LED Indicator 13. RF Transceiver Board
4. Power LED Indicator 14. INT/EXT Antenna Jumpers
5. Output Relay LED Indicators 15. Programming Port
6. Infrared Sensors 16. Function Dipswitches
7. Remote Pairing Button 17. Function Jumpers
8. System Information 18. Channel Dipswitch
9. Cord Grip 19. AC Line Filter/Relay Board
10. Mounting Bracket 20. Power Transformer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Flex Wave Technical Manual
April 2021
Page 17 of 96
3.3.1.2 Output Relay Contact Diagram
* For 9-36VDC power supply, wire #1 corresponds to the negative charge (-) and wire #3 corresponds to the positive charge (+). Wire #2 is for
GROUND.
* If PB3 (or PB4) is set to A/B pushbutton select function, connect output A to K5 (or K6) and output B to K7 (or K8). See Section 4.1.12.5 on
page 39 on how to set to this function.
* Due to the possibility of voltage spikes on the contactors, suppressors are recommended on contactors being driven by Flex relays.
REV (PB2)
FWD (PB1)
FWD 2
nd
REV 2
nd
REV (PB4)
FWD (PB3)
FWD 2
nd
REV 2
nd
Flex Wave Technical Manual
April 2021
Page 18 of 96
3.3.2 6Wave Receiver
3.3.2.1 External and Internal Illustrations
1. External RP-TNC Antenna Port 11. Mounting Bracket Release
2. COM LED Indicator 12. Decoder Board
3. Status LED Indicator 13. RF Transceiver Board
4. Power LED Indicator 14. INT/EXT Antenna Jumpers
5. Output Relay LED Indicators 15. Programming Port
6. Infrared Sensors 16. Function Dipswitches
7. Remote Pairing Button 17. Function Jumpers
8. System Information 18. Channel Dipswitch
9. Cord Grip 19. AC Line Filter/Relay Board
10. Mounting Bracket 20. Power Transformer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Flex Wave Technical Manual
April 2021
Page 19 of 96
3.3.2.2 Output Relay Contact Diagram
* For 9 - 36VDC power supply, wire #1 corresponds to the negative charge (-), wire #3 corresponds to the positive charge (+), and wire #2 is for
GROUND.
* Due to the possibility of voltage spikes on the contactors, suppressors are recommended on contactors being driven by Flex relays.
Flex 6Wave
COM 1
FWD (PB1)
REV (PB2)
FWD 2
nd
REV 2
nd
COM 2
FWD (PB3)
REV (PB4)
FWD 2
nd
REV 2
nd
COM 3
FWD (PB5)
REV (PB6)
FWD 2
nd
REV 2
nd
Flex Wave Technical Manual
April 2021
Page 20 of 96
3.3.3 8Wave Receiver
3.3.3.1 External and Internal Illustrations
1. External TNC Antenna Port 12. Decoder Board
2. COM LED Indicator 13. RF Transceiver Board
3. Status LED Indicator 14. INT/EXT Antenna Jumpers
4. Power LED Indicator 15. Programming Port
5. Output Relay LED Indicators 16. Function Dipswitches
6. Infrared Sensors 17. Function Jumpers
7. Remote Pairing Button 18. Channel Dipswitch
8. System Information 19. AC Line Filter/Relay Board
9. Cord Grip 20. Power Transformer
10. Mounting Bracket 21. Voltage Selector
11. Mounting Bracket Release
1
2
5
4
3
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Magnetek Flex Wave™ Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI