Astria Fireplaces Vega Instruction Sheet

Brand: Astria Fireplaces

Model: Vega

Type: Instruction Sheet

KIT CONTENTS

32" Fiber Panel Kit VFLK-32

Description Part No. Qty.

Rear Panel F3034 1

Right Side Panel F3031 1

Left Side Panel F3028 1

Retainer Brackets J5185 2

#10 Screws 4

36" Fiber Panel Kit VFLK-36

Description Part No. Qty.

Rear Panel F3035 1

Right Side Panel F3032 1

Left Side Panel F3029 1

Retainer Brackets J5185 2

#10 Screws 4

42" Fiber Panel Kit VFLK-42

Description Part No. Qty.

Rear Panel F3036 1

Right Side Panel F3033 1

Left Side Panel F3030 1

Retainer Brackets J5185 2

#10 Screws 4

TOOLS REQUIRED:

• Phillips Screwdriver

• 5/16'' Hex Socket Wrench or Nut Driver

GENERAL INFORMATION

This ﬁ ber liner accessory is approved for use in Vegas32Z6, Vega36Z6

and Vegas42Z6 series vent-free ﬁ reboxes. Do not use ﬁ ber liner acces-

sory in any other ﬁ replace models.

If you encounter any problems, need clariﬁ cation of these instructions or

are not qualiﬁ ed to properly install this kit, contact your local distributor

or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPERA-

TION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE

INSTRUCTIONS.

Check the contents of the kits upon receipt and check for any damaged

or missing parts. If there is hidden damage, notify your freight company

or your local distributor or dealer. Figure 1 - Fiber Liner Kit

Screws

Retaining

Bracket

Retaining

Bracket

Left Side

Panel

Right Side

Panel

Rear Panel

Gas Line

Knockout

F2719, F2720 AND F2721 FIBER LINER KIT INSTALLATION INSTRUCTIONS

[FOR USE IN FIREPLACE MODELS VEGAS32Z6, VEGA36Z6 & VEGAS42Z6 SERIES VENT-FREE FIREBOXES]

SOFT RUSTIC FIBER LINER KITS

P/N 900784-00

Rev. NC, 07/2016

HEARTH PRODUCTS

KITS AND ACCESSORIES

WARNING: Turn off, unplug, and let ﬁ replace cool before

installing ﬁ ber liner. Only a qualiﬁ ed service person should

service and repair ﬁ replace.

NOTICE: If already installed, you must remove log base as-

sembly before installing ﬁ ber liner. Refer to log base assembly

Installation and Operation Instructions manual.

WARNING: A qualiﬁ ed service person must connect and

disconnect ﬁ replace to gas supply. Follow all local codes.

IHP.US.com

900784-00 NC 1

NOTE: Some installations may require the gas supply line to be discon-

nected before removing log assembly. If so, call a qualiﬁ ed service person

to disconnect gas supply from ﬁ replace.

IMPORTANT: Always handle ﬁ ber panels with two hands.

Figure 2 - Fiber Panels with Retaining Brackets and Gas Knockout

INSTALLATION INSTRUCTIONS

1. Install rear ﬁ ber panel on back wall. Rest bottom edge of ﬁ ber

panel on ﬁ rebox ﬂ oor. Lean ﬁ ber against back wall of ﬁ rebox

while installing side panels.

NOTE: The rear panel is held in place by two side panels.

2. Gently slide left side ﬁ ber into place while holding rear ﬁ ber

panel upright against ﬁ rebox back.

3. Use supplied retainer bracket and screw to secure side ﬁ ber

panel to ﬁ rebox (see Figure 2).

4. Repeat steps 2 and 3 for right side ﬁ ber panel.

5. There is a gas knockout in each side panel for the gas line to

feed through (see Figure 2). Determine on which side the gas

connection will be located. Using a utility knife or cutting blade,

remove the identiﬁ ed gas knockout.

6. Replace log base if removed for ﬁ ber panel installation (see log

base Installation And Operation Instructions manual for proper

installation).

Screws

Retaining

Bracket Retaining

Bracket

Gas

Knockout

P/N 900784-00 Rev. NC 07/2016

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ ca-

tions, prices and also to discontinue colors, styles and products. Consult your local distributor

for ﬁ replace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

CAUTION: Always handle ﬁ ber panels with two hands. Do

not force ﬁ ber panels into place. Excessive force will break

ﬁ ber panels.

WARNING: Test all gas piping and connections for leaks after

installing or servicing. Correct all leaks at once.

WARNING: Never use an open ﬂ ame to check for a leak.

Apply a noncorrosive leak detection ﬂ uid to all joints. Bubbles

forming show a leak. Correct all leaks at once.

Astria Fireplaces Vega Instruction Sheet

Astria Fireplaces Vega Instruction Sheet

Astria Fireplaces Vega Instruction Sheet

Related papers

Other documents