ESAB PowerCut 400 PT-39 User manual

Valid for serial no. 145-xxx-xxxx0463 278 031 US FR SA 20121125

PowerCut

ä

700

PT-39

US Instruction manual

FR Manuel d'instructions

SA Manual de instrucciones

- 2 -

Sous réserve de modifications sans avis préalable.

Rights reserved to alter specifications without notice.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

English US 3.............................................

Français 25...............................................

Español SA 47.............................................

English US

- 3 -

TOCa

1 USER RESPONSIBILITY 4............................................

2 SAFETY PRECAUTIONS 4............................................

3 INTRODUCTION 8...................................................

3.1 Equipment 8................................................................

4 TECHNICAL DATA 9.................................................

5 INSTALLATION 10....................................................

5.1 Delivery check and location 11.................................................

5.2 Primary power supply 11......................................................

5.3 Input air connection 12........................................................

5.4 Connection for return cable 12.................................................

5.5 Torch connection 13..........................................................

6 OPERATION 15.......................................................

6.1 Connections 15..............................................................

6.2 Control devices 16...........................................................

6.2.1 Symbol key 17..........................................................

6.3 Installing consumables 18.....................................................

6.4 Cutting 19...................................................................

7 MAINTENANCE 20....................................................

7.1 Inspection and cleaning 21....................................................

8 TROUBLESHOOTING 22..............................................

8.1 Troubleshooting guide 23......................................................

9 ORDERING SPARE PARTS 24.........................................

SCHEMATIC DIAGRAM 70................................................

APPLICATIONS 72.......................................................

WEAR COMPONENTS 74.................................................

ORDERING NUMBER 75.................................................

- 4 -

US warninga

Be sure this information reaches the operator.

You can get extra copies through your supplier.

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the

principles of operation and safe practices for arc welding equipment, we urge you to read

our booklet, “Precautions and Safe Practices for Arc, Cutting and Gouging, “Form 52-529.

Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT

attempt to install or operate this equipment until you have read and fully understand these

instructions. If you do not fully understand these instructions, contact your supplier for

further information. Be sure to read the Safety Precautions before installing or operating

this equipment.

1 USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and

accompanying labels and/or insert when installed, operated, maintained and repaired in accordance

with the instruction provided. This equipment must be checked periodically. Malfunctioning or poorly

maintained equipment should not be used. Parts that are broken, missing, worn, distorted or

contaminated should be replaced immediately. Should such repair or replacement become necessary,

the manufacturer recommends that a telephone or written request for service advice be made to the

Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the

manufacturer. The user of this equipment shall have the sole responsibility for any malfunction which

results from improper use, faulty maintenance, damage, improper repair or alteration by anyone other

than the manufacturer or a service facility designated by the manufacturer.

2 SAFETY PRECAUTIONS

WARNING: These Safety Precautions are for your protection. They summarize precautionary

information from the references listed in Additional Safety Information section. Before performing any

installation or operating procedures, be sure to read and follow the safety precautions listed below as

well as all other manuals, material safety data sheets, labels, etc. Failure to observe Safety

Precautions can result in injury or death.

PROTECT YOURSELF AND OTHERS

Some welding, cutting and gouging processes are noisy and require ear

protection. The arc, like the sun, emits ultraviolet (UV) and other radiation

and can injure skin and eyes. Hot metal can cause burns. Training in the

proper use of the processes and equipment is essential to prevent accidents.

Therefore:

1. Always wear safety glasses with side shields in any work area, even if welding helmets face

shields and goggles are also required.

US

- 5 -

US warninga

2. Use a face shield fitted with the correct filter and cover plates to protect your eyes, face, neck

and ears from sparks and rays of the arc when operating or observing operations. Warn

bystanders not to watch the arc and not to expose themselves to the rays of the electric-arc or

hot metal.

3. Wear flameproof gauntlet type gloves, heavy long-sleeve shirt, cuffless trousers, high-topped

shoes and a welding helmet or cap for protection, to protect against arc rays and hot sparks or

hot metal. A flameproof apron may also be desirable as protection against radiated heat and

sparks.

4. Hot sparks or metal can lodge in rolled up sleeves, trouser cuffs, or pockets. Sleeves and collars

should be kept buttoned and open pockets eliminated from the front of clothing.

5. Protect other personnel from arc rays and hot sparks with a suitable nonflammable partition or

curtains.

6. Use goggles over safety glasses when chipping slag or grinding. Chipped slag may be hot and

can fly far. Bystanders should also wear goggles over safety glasses.

FIRES AND EXPLOSIONS

Heat from flames and arcs can start fires. Hot slag or sparks can also cause

fires and explosions. Therefore:

1. Remove all combustible materials well away from the work area or cover the materials with a

protective nonflammable covering. Combustible materials include wood, cloth, sawdust, liquid

and gas fuels, solvents, pants and coatings paper, etc.

2. Hot sparks or hot metal can fall through cracks or crevices in floors or wall openings and cause a

hidden smoldering fire or fires on the floor below. Make certain that such openings are protected

from hot sparks and metal.

3. Do not weld, cut or perform other hot work until the workpiece has been completely cleaned so

that there are no substances on the workpiece which might produce flammable or toxic vapors.

Do not do hot work on closed containers. They may explode.

4. Have fire extinguishing equipment handy for instant use, such as a garden hose, water pail, sand

bucket, or portable fire extinguisher. Be sure you are trained in its use.

5. Do not use equipment beyond its ratings. For example, overloaded welding cable can overheat

and create a fire hazard.

6. After completing operations, inspect the work area to make certain there are no hot sparks or hot

metal which could cause a later fire. Use fire watchers when necessary.

7. For additional information refer to NFPA Standard 51B, “Fire Prevention in Use of Cutting and

Welding Processes”, available from the National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

ELECTRICAL SHOCK

Contact with live electrical parts and ground can cause severe injury or

death. DO NOT use AC welding current in damp areas, if movement is

confined, or if there is danger of falling. Therefore:

1. Be sure the power source frame (chassis) is connected to the ground system of the input power.

2. Connect the workpiece to a good electrical ground.

3. Connect the work cable to the workpiece. A poor or missing connection can expose you or others

to a fatal shock.

4. Use well-maintained equipment. Replace worn or damaged cables.

5. Keep everything dry, including clothing, work area, cables, torch/electrode holder and power

source.

6. Make sure that all parts of your body are insulated from work and

from ground.

7. Do not stand directly on metal or the earth while working in tight quarters or a damp area; stand

on dry boards or an insulating platform and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn off the power before removing your gloves.

10. Refer to ANSI/ASC Standard Z49.1 (listed on next page) for specific grounding

recommendations. Do not mistake the work lead for a ground cable.

US

- 6 -

US warninga

ELECTRIC AND MAGNETIC FIELDS

May be dangerous. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding and cutting current

creates EMF around welding cables and welding machines.

Therefore:

1. Welders having pacemakers should consult their physician before welding. EMF may interfere

with some pacemakers.

2. Exposure to EMF may have other health effects which are unknown.

3. Welders should use the following procedures to minimize exposure to EMF:

a. Route the electrode and work cables together. Secure them with tape when possible.

b. Never coil the torch or work cable around your body.

c. Do not place your body between the torch and work cables. Route cables on the same side

of your body.

d. Connect the work cable to the workpiece as close as possible to the area being welded.

e. Keep welding power source and cables as far away from your body as possible.

FUMES AND GASES

Fumes and gases, can cause discomfort or harm, particularly in confined

spaces. Do not breathe fumes and gases. Shielding gases can cause

asphyxiation.

Therfore:

1. Always provide adequate ventilation in the work area by natural or mechanical means. Do not

weld, cut or gouge on materials such as galvanized steel, stainless steel, copper, zinc, lead

beryllium or cadmium unless positive mechanical ventilation is provided. Do not breathe fumes

from these materials.

2. Do not operate near degreasing and spraying operations. The heat or arc can react with

chlorinated hydrocarbon vapors to form phosgene, a highly toxic gas and other irritant gases.

3. If you develop momentary eye, nose or throat irritation while operating, this is an indication that

ventilation is not adequate. Stop work and take necessary steps to improve ventilation in the work

area. Do not continue to operate if physical discomfort persists.

4. Refer to ANSI/ASC Standard Z49.1 (see listing below) for specific ventilation recommendations.

5. WARNING: This product when used for welding or cutting, produces fumes or gases which

contain chemicals known to the State of California to cause birth defects and in some cases

cancer (California Health & Safety Code §25249.5 et seq.)

CYLINDER HANDLING

Cylinders, if mishandled, can rupture and violently release gas. Sudden

rupture of cylinder valve or relief device can injure or kill.

Therefore:

1. Use the proper gas for the process and use the proper pressure reducing regulator designed to

operate from the compressed gas cylinder. Do not use adaptors. Maintain hoses and fittings in

good condition. Follow manufacturer's operating instructions for mounting regulator to a

compressed gas cylinder.

2. Always secure cylinders in an upright position by chain or strap to suitable hand trucks,

undercarriages, benches, wall, post or racks. Never secure cylinders to work tables or fixtures

where they may become part of an electrical circuit.

3. When not in use, keep cylinder valves closed. Have valve protection cap in place if regulator is

not connected. Secure and move cylinders by using suitable hand trucks.

4. Locate cylinders away from heat, sparks and flames. Never strike an arc on a cylinder.

5. For additional information, refer to CGA Standard P-1, “Precautions for Safe Handling of

Compressed Gases in Cylinders”, which is available from Compressed Gas Association, 1235

Jefferson Davis Highway, Arlington, VA 22202.

US

- 7 -

US warninga

EQUIPMENT MAINTENANCE

Faulty or improperly maintained equipment can cause injury or death. Therefore:

1. Always have qualified personnel perform the installation, troubleshooting and maintenance work.

Do not perform any electrical work unless you are qualified to perform such work.

2. Before performing any maintenance work inside a power source, disconnect the power source

from the incoming electrical power.

3. Maintain cables, grounding wire, connections, power cord and power supply in safe working

order. Do not operate any equipment in faulty condition.

4. Do not abuse any equipment or accessories. Keep equipment away from heat sources such as

furnaces, wet conditions such as water puddles, oil or grease, corrosive atmospheres and

inclement weather.

5. Keep all safety devices and cabinet covers in position and in good repair.

6. Use equipment only for its intended purpose. Do not modify it in any manner.

ADDITIONAL SAFETY INFORMATION

For more information on safe practices for electric arc welding and cutting equipment,

ask your supplier for a copy of “Precautions and Safe Practices for Arc Welding,

Cutting and Gouging”, Form 52-529.

The following publications, which are available from the American Welding Society, 550 N.W. LeJuene

Road, Miami, FL 33126, are recommended to you:

1. ANSI/ASC Z49.1 - “Safety in Welding and Cutting”

2. AWS C5.1 . “Recommended Practices for Plasma Arc Welding”

3. AWS C5.2 - “Recommended Practices for Plasma Arc Cutting“

4. AWS C5.3 - “Recommended Practices for Air Carbon, Arc Gouging and Cutting”

5. AWS C5.5 - “Recommended Practices for Gas Tungsten Arc Welding”

6. AWS C5.6 - “Recommended Practices for Gas Metal Arc welding”

7. AWS SP - “Safe practices” - Reprint, Welding Handbook

8. ANSI/AWS F4.1 - “Recommended Safe Practices for Welding and Cutting of Containers That

Have Held Hazardous Substances”

MEANING OF SYMBOLS

As used throughout this manual: Means Attention! Be Alert!

Means immediate hazards which, if not avoided, will result in

immediate, serious personal injury or loss of life.

Means potential hazards which could result in personal injury or loss

of life.

Means hazards which could result in minor personal injury.

US

- 8 -

bp23aa

This product is solely intended for plasma cutting. Any other use may result in

personal injury and / or equipment damage.

Read and understand the instruction manual

before installing or operating.

ESAB can provide you with all necessary cutting protection and accessories.

3 INTRODUCTION

The PowerCut 700 is a complete system for manual plasma cutting. It delivers

cutting power for severing materials up to 5/8” (16 mm) thickness.

3.1 Equipment

The power source is supplied with:

S power cable, 10 ft (3 m)

S instruction manual

S return cable with clamp

S plasma cutting torch PT-39, 25 ft (7.5 m), supplied as indicated on page 75.

US

- 9 -

bp23aa

4 TECHNICAL DATA

PowerCut 700

Mains voltage 230V $15 %, 1ph, 50/60Hz

Setting range 30 – 50A

Permitted load

25 % duty cycle

60 % duty cycle

100% duty cycle

50A

37A

30A

Power factor at max current 0.75

Efficiency at maximum current 80%

Open-circuit voltage U

0

320V

Operating temperature - 50 to 104°F ( -10 to 40°C)

Transportation temperature - 68 to 131°F (-20 to 55°C)

Sound pressure at no load < 49db (A)

Nominal flow rate 400cfh at 70psig(189l/min at 4.8bar)

Dimensions, l x w x h 22”x8.3”x15” (557x 211 x 380mm)

Weight incl torch and return cable 47lbs (21.3kg)

Insulation class transformer H

Enclosure class IP 23

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 104° F.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP 23 is designed for indoor and outdoor use.

US

- 10 -

bp23aa

5 INSTALLATION

The installation must be done by a professional.

Correct installation is very important for trouble-free operation and good cutting

results. Carefully read and follow each step in this chapter.

ELECTRIC SHOCKS CAN KILL. TAKE PRECAUTIONARY MEASURES AGAINST

ELECTRIC SHOCKS. ENSURE THAT ALL POWER SUPPLIES ARE DISCONNECTED

– SWITCH OFF THE SWITCH AT THE WALL SOCKET AND PULL OUT THE

EQUIPMENT'S POWER CABLE FROM THE SOCKET BEFORE MAKING ANY

ELECTRICAL CONNECTIONS IN THE POWER SOURCE.

IT IS VERY IMPORTANT THAT THE CHASSIS IS CONNECTED TO THE APPROVED

ELECTRIC PROTECTIVE EARTH, TO PREVENT ELECTRIC SHOCKS AND

ELECTRICAL ACCIDENTS. ENSURE THAT PROTECTIVE EARTH IS NOT

CONNECTED TO ANY PHASE CONDUCTORS BY MISTAKE.

POOR CONNECTIONS OR FAILURE TO CONNECT THE RETURN CABLE TO THE

WORKPIECE CAN RESULT IN FATAL ELECTRIC SHOCK.

AIR FILTER DEVICES MAY NOT BE USED – INSTALLATION OR MOUNTING OF ANY

FORM OF AIR FILTER DEVICE PREVENTS THE COLD AIR FLOW AND CAUSES A

RISK OF OVERHEATING. THE WARRANTY IS INVALIDATED IF ANY TYPE OF AIR

FILTER IS USED.

DO NOT START THE EQUIPMENT WITH THE COVER REMOVED.

DO NOT CONNECT THE EQUIPMENT UNDER TENSION OR WHEN YOU ARE

HOLDING IT OR CARRYING IT.

DO NOT TOUCH ANY OF THE TORCH'S PARTS WHEN THE POWER SUPPLY IS ON.

This product is intended for industrial use. In a domestic environment this product

may cause radio interference. It is the user's responsibility to take adequate

precautions.

US

- 11 -

bp23aa

Place the power source at least 3 metres from the cutting area as sparks and slag spray can

damage the power source

5.1 Delivery check and location

1. Remove the packaging. Inspect the equipment for damage that was not

immediately apparent upon reception of the delivery. Immediately report any

damage to the delivery company.

2. Check for any loose parts in the packaging. Check that the air ducts in the

cover's rear panel are not blocked with packaging material that can prevent the

air flow through the power source.

The power source has a carrying handle and can be lifted easily.

3. Position the power source so that its cooling air inlets and outlets are not

obstructed. Minimum permitted distance to wall or other obstruction is 3.3 ft (1 m).

4. An air source that gives clean and dry air, at least 400 cfh (189 l/m) at 70 psi

(4.8 bar), is required for cutting. The cutting air pressure must not exceed 87 psi

(6 bar), which is the maximum inlet pressure for the filter regulator that is

included in the delivery.

5.2 Primary power supply

Make sure that the power source is connected to the correct supply voltage and that

it is protected by the correct fuse rating. A protective earth connection must be made

in accordance with regulations.

Rating plate with supply connection data

MAKE SURE THE POWER SOURCE IS SWITCHED OFF BEFORE REMOVING THE

FUSE.

US

- 12 -

bp23aa

Recommended sizes for input conductors and line fuses

Input requirement Input & Gnd

conductors

Line fuse

Volt Phase Amps Cu/Awg Amps

230 1 41 8 50

Supply from power generators

The power source can be supplied from different types of generators. However,

some generators may not provide sufficient power for welding. The generators with

AVR, equivalent or better type of regulation with a min rated power of 10.8 kW are

recommended to supply the power source within it's full capacity.

Start with generator:

1) Start the generator

2) Turn on the power source by mains switch ON

Stop with generator

3) Turn off the power source by mains switch OFF

4) Stop the generator

5.3 Input air connection

Connect your air supply to the inlet connection of the filter. Any cylinder of

compressed air or air from a compressor may be used. The air must be free from

polluting particles. A pressure regulator is provided to ensure the correct air flow rate

on the torch. Set the pressure with the knob on the top of the regulator.

5.4 Connection for return cable

Clamp the return cable to the workpiece. Be sure the workpiece is connected to an

approved earth ground with a properly sized ground cable.

US

- 13 -

bp23aa

5.5 Torch connection

For fast and easy separation of the torch from the power supply, the Power Cut 700

is equipped with a unique quick disconnect system.

Before connecting or disconnecting the torch, please keep these safety rules in

mind.

S If the connector is loose or damaged, do no operate the system until it has been

repaired by a qualified professional. Always make sure that the connection is

tight and properly locked in place.

S Never, under any circumstances, disconnect the torch while the equipment is on.

The system should be unplugged or otherwise disconnected from power prior to

servicing.

S Never pull the power supply by its cables, or do anything that might damage the

cable or connector. The connector is designed to withstand wear from regular

use, but excessive abuse can render the connector unusable.

S Like the power supply itself, the connector should never be operated in or near

standing water. Additionally, if the connector’s silicon moisture seal is absent or

damaged, do not operate the system.

S The gas connection is lubricated to ensure a smooth connection, but the

electrical connector should never be lubricated. Make sure to keep the electrical

connections clean and dry.

US

- 14 -

bp23aa

5.5.1 Disconnecting the Torch

Always obey the safety rules above.

1. Disconnect the power at the wall or unplug the power supply.

2. Press the nylon tab on the torchside connector.

3. Pull the two halves apart while holding the tab down.

5.5.2 Connecting the Torch

Always obey the safety rules above.

1. Disconnect the power at the wall or unplug the power supply.

2. Press the release button on the female gas connector to make sure that the

locking mechanism is not engaged.

3. Align the gas connectors and engage them.

4. Align the electrical connections and engage them.

5. Press the two halves together until you hear the click that indicates that the gas

connectors are locked together.

6. Pull on the connector gently to make sure that it is properly locked in place.

US

- 15 -

bp23aa

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 4. Read through before you start using the equipment!

6.1 Connections

1 Fuse 4 Control devices, see chapter 6.2

2 Connection for air 5 Connection for torch

3 Connection for power cable 6 Connection of return cable with clamp

US

- 16 -

bp23aa

6.2 Control devices

1 Power switch 0/1 5 Over Temperature Indicator

2 2/4 stroke 6 Parts in Place (PIP)

3 Air Pressure Indicator 7 Power ON Indicator

4 Fault Indicator 8 Output current control

1 Power switch

Turn the knob clockwise to “1” position for normal operation. Turn the knob

counterclockwise to switch “0”.

2 2/4 stroke

When in 2-stroke cutting mode, the torch activates when the trigger is pressed, and

deactivates when the trigger is released. In 4-stroke mode, the torch activates on the

first trigger press, after which it can be released for increased comfort during long

cuts. The torch is then deactivated by pressing the trigger again.

3 Air Pressure Indicator

The yellow LED indicates that the air pressure is too low.

4 Fault Indicator

The blinking yellow LED indicates that the safety switch for the cover is activated and

the power is automatically turned off.

US

- 17 -

bp23aa

5 Over Temperature Indicator

When the yellow led is lit, the working temperature has exceeded the normal values.

It is turned off when the temperature is normal.

6 Parts in Place (PIP)

When the yellow led is lit, it indicates that there is a parts-in-place error. This means

that no nozzle was detected, or that the electrode is not retracting properly. Turn off

the power. Check that the components are properly assembled, that they are free

from excessive damage, and that the electrode can slide back and forth with

comfortable pressure from one finger. Once the source of the error has been

corrected, turn on the power again.

7 Power ON Indicator

When the green led is lit, it indicates that the power is on.

8 Output current control

Adjustable from 30 to 50 A. For settings see cut data charts in the torch manual.

6.2.1 Symbol key

Power Air

Temperature Fault

PIP

Parts in Place 2-stroke

4-stroke

US

- 18 -

bp23aa

6.3 Installing consumables

Proper use of the torch within rated operating conditions (especially arc current and

gas flow rate) and firm installation of consumable parts can prevent unnecessary

torch damage.

1. Tighten electrode and retaining/shield cup fully at each consumable change or

inspection.

2. Check consumable thightness at the beginning of each work period, even if

everything was working normally at the end of the previous period.

A Torch body assembly

B Baffle

C Electrode

D Nozzle

E Retaining/Shield cup

F Piston

G Electrode/Torch body seat

See wear components, page 74.

US

- 19 -

bp23aa

6.4 Cutting

1. Set the switch (wall socket or similar) to on.

2. Check that the compressor is connected to the power source.

3. Set the power switch to I (On).

4. After starting the cut, the torch should be maintained at a 5 - 15° forward angle.

This angle is especially useful in helping to create a “drop” cut. The torch can be

operated with the nozzle dragging on the pate or with up to ¼” (6.35 mm)

standoff. The ideal standoff is 1/8” (3.2 mm). Standoff guides are available to

make maintaining the gap easier, see page 74.

5. Depress the torch switch. Air should flow from the torch nozzle.

6. Two seconds after depressing the torch switch, the pilot arc should start. The

main arc should immediately follow, allowing the cut to begin. (If working in the

4-stroke mode, the torch switch may be released after establishing the cutting

arc.)

7. To start a cut, tilt the torch to prevent molten material from coming back against

and damaging the torch. When the arc breaks through the workpiece, bring the

torch to an upright position and proceed to cut.

8. When ending a cut, the torch switch should be released and the torch lifted off

the workpiece immediately upon completion of the cut. This is to prevent the pilot

arc from re-igniting after cutting arc extinguishes and causing damage to the

nozzle (double arcing).

9. For rapid re-starts on machines that support grate cutting mode, do not release

the torch switch. The torch will automatically return to pilot arc mode after each

cut and transfer back to main arc, when the torch is positioned over the next

working surface. When working without grate cutting mode, simply release and

re-press the trigger during the postflow to restart the arc without a delay for

preflow.

US

- 20 -

bp23aa

Speed

Typically, manual plasma cutting speeds are limited by the sever speed. This

indicates the maximum speed you will be able to move the torch along the cut while

still penetrating the work piece. However, for applications that require a cleaner cut,

it may be important to cut closer to the quality speed.

If the cut is made too quickly, significant quantities of molten metal can form dross on

the underside of the cut. While most slag formed from carbon steel will easily chip

off, it can be a nuisance. Quality speeds are selected to keep dross formation to a

minimum.

On page 72 data show the maximum cutting speeds possible for the power source at

15 - 50A. Quality cut speed recommendations are also listed for steel.

Note that when the torch is used at its limits, the quality of the cut suffers.

7 MAINTENANCE

Regular maintenance is important to get the optimal performance and lifetime.

Only those persons who have appropriate electrical knowledge (authorized

personnel) may remove the safety plates.

ENSURE THAT THE MAINS VOLTAGE SUPPLY TO THE MACHINE HAS BEEN

DISCONNECTED EXTERNALLY. SWITCH OFF THE SWITCH AT THE WALL

SOCKET BEFORE INSPECTING OR WORKING IN THE POWER SOURCE.

WATER OR OIL CAN COLLECT IN THE COMPRESSED AIR LINES. ALWAYS DIRECT

THE FIRST STREAM OF AIR AWAY FROM THE EQUIPMENT, TO PREVENT

DAMAGE.

Supplier warranty is void if customer attempts any work on product during the

warranty period.

If the equipment does not work correctly, stop work immediately and determine the

cause of the problem. Maintenance work may only be carried out by persons with

the applicable knowledge. Electrical work may only be carried out by authorized

electricians. Never allow persons other than those with the applicable knowledge to

check, clean or repair the equipment. Only use ESAB Genuine spare parts.

US

Page is loading ...

ESAB PowerCut 400 PT-39 User manual

This manual is also suitable for

ESAB PowerCut 400 PT-39 User manual

in other languages

Related papers

Other documents