Siemens SIMATIC 877 User manual

Page is loading ...

Quick Start 06.07

6.6 Abmessungen der Fronten mit Remote Kit

Panel

A B C D E F G H I J K L

12" Touch

310,3 400,0 288,3 273,0 265,2 366,0 171,0 101,5 47,0 35,8 82,3 37,8

15" Touch

310,3 482,6 288,3 273,0 265,2 447,2 171,0 99,2 47,0 33,1 79,6 48,1

12" Tastatur

310,3 482,6 288,3 273,0 265,2 447,2 171,0 83,0 48,0 16,3 63,8 29,3

15" Tastatur

354,8 482,6 323,9 273,0 265,2 447,2 171,0 102,0 48,0 35,3 82,8 49,3

17" Touch

400,0 482,6 378,0 273,0 265,2 447,2 171,0 108,4 47,0 42,0 89,0 57,5

19" Touch

400,0 482,6 378,0 273,0 265,2 447,2 171,0 108,4 47,0 42,0 89,0 57,5

Toleranz: + 1 mm

Panel PC Remote Kit 27

A5E00447267V Doc.No.: b40013de1.doc

Page is loading ...

Quick Start 08.07

SIMATIC

Panel PC Remote Kit

for PC 677/677B/877

Operator Manual

Introduction

Unpacking the Units

1

2

Montage

3

Connecting

4

Start up

5

Technical Data

6

More assistance

7

This manual applies to devices with the

order numbers 6AV7671-1EA…..

Release 6/2007

A5E00447267V Doc.No.: b40013de1.doc

Quick Start 08.07

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to

prevent damage to property. The notices referring to your personal safety are highlighted in the manual by

a safety alert symbol; notices referring to property damage only have no safety alert symbol. These notices

shown below are graded according to the degree of danger.

!

Danger

Indicates that death or severe personal injury will result if proper precautions are not taken.

!

Warning

Indicates that death or severe personal injury may result if proper precautions are not taken.

!

Caution

With a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

Caution

Without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

Notice

Indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of

danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a

warning relating to property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Qualified

personnel may only perform Commissioning and operation of a device/system. Within the context of the

safety notes in this documentation qualified persons are defined as persons who are authorized to

commission, ground and label devices, systems and circuits in accordance with established safety

practices and standards.

Prescribed Usage

Note the following:

!

Warning

This device may only be sued for the applications described in the catalogue or the technical description

and only in connection with devices or components from other manufactures, which have been approved or

recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,

positioning and assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

The distribution and duplication of this document or the utilization and

transmission of its contents are not permitted without express written

permission. Offenders will be liable for damages. All rights, including

rights created by paten grant or registration of a utility model or design,

are reserved.

Siemens AG

Automation and Drives

Postfach 4848, 90327 Nuremberg, Germany

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency

with the hardware and software described. Since variance cannot be

precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary

corrections are included in subsequent editions.

Technical data subject to change

Panel PC Remote Kit

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

Table of contents

1 Introduction............................................................................................ 30

1.1. Overview.........................................................................................................30

1.2. Available combinations...................................................................................31

2 Unpacking the Units.............................................................................. 33

2.1. Safety note......................................................................................................33

2.2. Unpacking and checking the delivery unit......................................................34

2.3. Make note of identification data......................................................................35

3 Mounting................................................................................................. 36

3.1. Mounting Note ................................................................................................36

3.2. Mounting positions..........................................................................................36

3.2.1. Permitted mounting positions of the control unit ............................................36

3.2.2. Permitted mounting positions of the computer unit PC 677...........................37

3.2.3. Permitted of the computer unit PC 877 ..........................................................38

3.2.4. Degree of protection and type of fixation........................................................39

3.3. Mounting cut-out.............................................................................................39

3.4. Fixation and connection of the remote device to the control unit...................40

3.4.1. Connection of the remote device with the control unit....................................40

3.4.2. Fixation of the USB transmitter on the computer unit.....................................41

3.5. Assembly of the computer unit.......................................................................42

4 Connecting............................................................................................. 43

4.1. Overview.........................................................................................................43

4.2. Connection of the Panel PC with the control unit...........................................44

4.2.1. Interfaces of the remote device......................................................................44

4.2.2. Connecting of the control unit.........................................................................45

4.2.3. Block diagram short distance 5 m ..................................................................47

4.2.4. Block diagram long distance 10 m, 15 m, 20 m and 30 m.............................48

5 Start up ................................................................................................... 49

5.1. Overview.........................................................................................................49

5.2. Switch the device on: no driver.......................................................................50

5.3. Switch the device on: driver are installed.......................................................50

6 Technical Data........................................................................................ 51

6.1. EMC requirements..........................................................................................51

6.2. Power supply..................................................................................................51

6.3. Connector cable computer- control unit..........................................................52

6.3.1. DVI cable........................................................................................................52

6.3.2. USB cable.......................................................................................................53

6.3.3. Ethernet cable.................................................................................................53

6.4. Ambient and environmental conditions ..........................................................54

6.5. Dimensions of the remote device...................................................................54

6.6. Dimensions of front panels with Remote Kit...................................................55

7 More assistance..................................................................................... 56

Panel PC Remote Kit

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

1 Introduction

The SIMATIC Panel PC is an industry-standard PC platform for demanding tasks in the

field of PC-based automation.

The SIMATIC Panel PC provides detailed documentation in 6 languages in PDF format.

The documentation at hand describes the Start up of your device as a Panel PC Remote

Kit. The document includes also all information for the build up of the Panel PC Remote

Kit, which are not contained in documentation of the central configuration e.g. the

technical data.

Notice

Carry out the tasks in the sequence described. Observe all safety instructions.

Read the documentation thoroughly once you have completed commissioning. Observe all of the

safety instructions and notes included in the documentation.

1.1. Overview

Computer and control unit with the remote device will be delivered separate in the Panel

PC Remote Kit version. The control unit is assembled apart from the computer.

USB: Kupferkabel

DVI: Kupferkabel

Remote device

USB transmitter

USB: Copper cable

Fig. 1: Layout of the Panel PC Remote Kit

DVI: Copper cable

• The Remote device is indicted as receiver, will be mounted on the back of the control

unit.

• The optional key module will be mounted on the Remote device.

• The USB transmitter will be connected and mounted with computer.

• The single components will be connected with supplied cables.

Panel PC Remote Kit 30

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

1.2. Available combinations

Accessories of the Panel PC Remote Kit

• Wall angle bracket for PC677/677B

• Wall angle bracket for PC877

• Cover plate and screws for the interface port on the PC677/677B

• Cover plate and screws for the interface port on the PC877

• Countersunk screw

• Cable tie

Combination / Order no. Deliver item MLFB-No.

Remote device 24VDC

incl. accessories

6AV7671-1EX01-0AD0

5 m

6AV7671-1EA00-0AA1

Cable set 5 m

DVI-D- and USB cable

6AV7671-1EX10-5AA0

Remote device 24VDC

incl. accessories

6AV7671-1EX01-0AD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

10 m

6AV7671-1EA01-0AA1

Cable set 10 m

DVI-D- and USB cable

6AV7671-1EX11-0AA0

Remote device 24VDC

incl. accessories

6AV7671-1EX01-0AD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

15 m

6AV7671-1EA01-5AA1

Cable set 15 m

DVI-D- and USB cable

6AV7671-1EX11-5AA0

Remote device 24VDC

incl. accessories

6AV7671-1EX01-0AD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

20 m

6AV7671-1EA02-0AA1

Cable set 20 m

DVI-D- and USB cable

6AV7671-1EX12-0AA0

Remote device 24VDC

incl. accessories

6AV7671-1EX01-0AD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

Remote Kit

24 VDC

30 m

6AV7671-1EA03-0AA1

Cable set 30 m

DVI-D- and USB cable

6AV7671-1EX13-0AA0

Panel PC Remote Kit 31

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

Combination / Order no. Deliver item MLFB-No.

Remote device 100-240VAC incl.

accessories + power cable 1,5 m

6AV7671-1EX01-0BD0

5 m

6AV7671-1EA10-0AA1

Cable set 5 m

DVI-D- and USB cable

6AV7671-1EX10-5AA0

Remote device 100-240VAC incl.

accessories + power cable 1,5 m

6AV7671-1EX01-0BD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

10 m

6AV7671-1EA11-0AA1

Cable set 10 m

DVI-D- and USB cable

6AV7671-1EX11-0AA0

Remote device 100-240VAC incl.

accessories + power cable 1,5 m

6AV7671-1EX01-0BD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

15 m

6AV7671-1EA11-5AA1

Cable set 10 m

DVI-D- and USB cable

6AV7671-1EX11-5AA0

Remote device 100-240 VAC incl.

accessories + power cable 1,5 m

6AV7671-1EX01-0BD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

20 m

6AV7671-1EA12-0AA1

Cable set 20 m

DVI-D- and USB cable

6AV7671-1EX12-0AA0

Remote device 100-240VAC incl.

accessories + power cable 1,5 m

6AV7671-1EX01-0BD0

Transmitter

incl. USB cable 0,5 m

6AV7671-1EX02-0AA0

Remote Kit

100-240 VAC

30 m

6AV7671-1EA13-0AA1

Cable set 30 m

DVI-D- and USB cable

6AV7671-1EX13-0AA0

Panel PC Remote Kit 32

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

2 Unpacking the Units

2.1. Safety note

!

Warning

Emergencies

If the device malfunctions, remove the power cable immediately and contact your neares

t

customer service representative. Malfunctions can occur when the operator controls o

r

power cable are damaged or when liquids or foreign objects penetrate the device

Electrical connections

!

Warning

Disconnect the device from the power supply before every intervention.

Do not touch power lines or data transmission lines during electrical storms and do not

connect any cables.

High frequency radiation

Caution

Unintentional operation situation

High frequency radiation, e.g. from cell phones, can cause unintentional operation

situations under some circumstances. For more details, consult the technical data in the

“EMC Requirements” chapter.

Handling and disposal of lithium batteries

!

Warning

Danger of explosion and the release of harmful substances!

Do not throw lithium batteries into fire, do not solder onto the cell body, do not open, do

not short circuit, do not reverse pole, do not heat above 100°C, dispose of according to

regulations, and protect from direct sunlight, moisture and condensation.

Replace lithium batteries with the same brand or a brand recommended by the

manufacturer.

Dispose of used lithium batteries individually as hazardous waste in accordance with the

local regulations.

Panel PC Remote Kit 33

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

2.2. Unpacking and checking the delivery unit

Procedure

1. Please check the packaging material for transport damage upon delivery.

2. If any transport damage is present at the time of delivery, lodge a complaint at the

shipping company in charge. Have the shipper confirm the transport damage

immediately

3. Unpack the device.

4. Keep the packaging material in case you have to transport the unit again.

Notice

The packaging protects the device during transport and storage. Therefore, neve

r

dispose of the original packaging material.

5. Please keep the enclosed documentation in a safe place. You will need the

documentation when you start up the device for the first time.

6. Check the package contents for completeness and any visible transport damage.

Check for completeness using the enclosed “Contents of Delivery” list.

7. Notify the delivery service in charge immediately if the packages contents are

incomplete or damaged.

!

Warning

Make sure that a damaged device is not installed nor put into operation.

Panel PC Remote Kit 34

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

2.3. Make note of identification data

Procedure

Write down the Order number in the table in the chapter „Make note of identification data“

in the „Quick Start for the Computer“. The numbers are on the label of the Remote device

(see Fig. 2) and on the label of the Transmitter (see Fig. 3).

Fig. 2: Label of the Remote device

Fig. 3: Label of the USB transmitter

Panel PC Remote Kit 35

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3 Mounting

3.1. Mounting Note

Introduction

!

Warning

Do not touch power lines or data transmission lines during electrical storms and do not

connect any cables.

Disconnect complete the power supply by disconnecting the plug.

Condition

• The device is installed EMC-compatible.

• The device is installed according the manual.

• Take into account a space of 1 cm for circulation of air.

3.2. Mounting positions

3.2.1. Permitted mounting positions of the control unit

Approval

Certain installation positions are approved for the control unit of the Panel PC Remote Kit

Fig. 4: Approved installation positions for the control unit

Vertical installation and deviations between +20° and –20” in the given directions is

permitted.

Panel PC Remote Kit 36

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3.2.2. Permitted mounting positions of the computer unit PC 677

Mounting position according to UL508

An incline of ± 20° is allowed in every permitted position.

wall angle bracket

Position 1: preferred Position 2

The operation of CD-/DVD-driver and

floppy driver is not allowed.

Position 3: Desktop Position 3: Ceiling

Fig. 5: Mounting position for PC677/677B according to UL508

Mounting position according to UL508/CSA 22.2 No.142

An incline of ± 15° is allowed in this permitted position.

The operation of CD-/DVD-driver and floppy driver is not allowed.

Position 5: Interface on the bottom

Fig. 6: Mounting position for PC677/677B according to UL508/CSA 22.2

Panel PC Remote Kit 37

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3.2.3. Permitted of the computer unit PC 877

Mounting positions according to UL60950/UL508/EN60950/CSA22.2 No. 60950

An incline of ± 20° is allowed inn every permitted position.

Position 1: preferred Position 2

wall angle bracket

The operation of CD-/DVD-driver and

floppy driver is not allowed.

Position 3: Desktop Position 4: Ceiling

Fig. 7: Mounting position for PC877 according to UL60950/UL508/EN60950/CSA22.2

Mounting positions according to UL508/CSA 22.2 No. 142

An incline of ± 15° is allowed in this permitted position.

The operation of CD-/DVD-driver and floppy driver is not

allowed.

Position 5: Interface on the bottom

Fig. 8: Mounting position for PC877 according to UL508/CSA 22.2

Panel PC Remote Kit 38

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3.2.4. Degree of protection and type of fixation

Information to degree of protection and type of fixation can be found in chapter

„Application planning“ in the manual for the control unit

3.3. Mounting cut-out

Select and complete recessed mounting cut-out

Range of validity

The computer unit of the Panel PC Remote Kit needs no mounting cut-off.

The following applies to centralized configuration and for the control unit of the Panel PC

Remote Kit.

Requirement

The degree of protection and type of fixation for the application are selected. (According

to the instruction manual Panel PC)

Procedure

1. Please follow the installation guidelines.

2. Select a location suitable for installation, taking into account the installation

guidelines.

3. On the basis of the dimension diagrams, check whether the required screw and

pressure points on the backside and the hatched seal area are easily accessible after

the completion of the installation cut-out. Otherwise the installation cut-out is useless

4. Complete the installation cut-out according to the dimension diagrams in chapter 3.6

„Mounting cut-off“ in the manual Panel PC. Please take into account the installation

depth of the control unit and the remote device. The dimensions of the remote device

can be found in chapter 6.5.

Panel PC Remote Kit 39

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3.4. Fixation and connection of the remote device to the control unit

3.4.1. Connection of the remote device with the control unit

Procedure

1. The ribbon cables and the USB-cable of the control unit are connected with the

remote device. The white plug socket and the USB-socket will be used at the 12”

and 15” control unit. The four cables will be connected to the remote device

accordant to the marking on the cable and the device if a control unit with a SXGA

(1,280 x 1,024) resolution is used.

2. The remote device is fitted on the second side.

3. The remote device is fixed with four screws.

Fitting clamp of the remote

de

vi

ce

Fig. 9: Remote device and control unit

K1

K2 USB

K3

Fig. 10: Position of the interface for the connection

Panel PC Remote Kit 40

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

Description of the interface

K1 (X44) Display Select Coding

Automatic configuration of the display

K2 (X300) LVDS port 1

Connector for 12“ and 15” TFT Panel front via a LVDS receiver

K3 (X310) LVDS port 2 (black)

Second connector for Display with resolution of SXGA

USB Connector for the USB interface on the front of the control unit.

3.4.2. Fixation of the USB transmitter on the computer unit

Mounting possibilities:

1. Mounting on the Box-PC

2. Mounting sidewise on the PC-Box (an angle bracket should be used)

3. External Mounting

Fig. 11: USB transmitter mounting possibilities

Panel PC Remote Kit 41

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

3.5. Assembly of the computer unit

Note

The port of the LCD interface for the centralized configuration has to be closed before the

computer unit will be assembled. (Interface port see Operating instructions “SIMATIC

Panel PC 677/677B, computer unit” and PC 877 respectively, chapter “Connection

element”,). The supplied cover plates will be used for it.

Range of validity

The following is only valid for computer unit in the Panel PC Remote Kit configuration.

The additional information for the centralized configuration can be found in the accordant

chapters in the operator instructions of the computer unit.

Screw on of the wall angle bracket

Included in the delivery of the Panel PC Remote Kit are two wall angle brackets, which

will be fixed on the computer unit with 6 screws M3x6 (see Fig. 5 and Fig. 7).

Instruction for the fixation on the wall and the roof.

Examples for the fixation types

Material Hole diameter Fixation

Concrete 8 mm diameter, 60 mm depth Screw anchor: 8 mm, 50 mm

Screw 4 mm, 50 mm

Hard plaster board

minimum thickness

13 mm

14 mm diameter Screw anchor

Diameter 4 mm

Length minimum 50 mm

Metal

minimum thickness

12 mm

5 mm diameter Metal screws

Diameter 4 mm

Length minimum 15 mm

!

Warning

Make sure that the wall or roof is able to bear the minimum weight of 3 times the weight

of the unit with the wall angle bracket and the additional devices. The weight can be

found in the chapter “Technical Date” in the Instruction manual of the Panel PC.

Panel PC Remote Kit 42

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

4 Connecting

4.1. Overview

Introduction

After the mounting the unit will be connected.

!

Warning

Do not touch power lines or data transmission lines during electrical storms and do not

connect any cables.

Do always unplug the power supply for complete disconnection of the power.

Caution

Sequence of the connection

To avoid a damage of the device, take care about the sequence of the connecter.

Start up

Before connecting the device have to be adjusted to ambient temperature. Don’t put the

device in direct heat radiation. At condensation after the waiting time of 12 hours the

device can be switched on.

Risk of data loss

Don’t switch of the power supply if the device operates. Disconnect the power supply

after proper shut down of the unit.

Condition

• The device is installed EMC-compatible.

• The device is installed according the manual.

Procedure

1. Connecting the potential equalisation

2. Connecting I/O devices

- Connecting control unit see chapter 4.2.2

- Connecting PS/2 mouse

- Connecting serial mouse

- Connecting PS/2 keyboard

- Connecting USB devices, e.g. USB mouse

- Connecting printer

3. The control unit of the PC Remote Kit is connected to the computer unit with the

supplied cables. (see chapter 4.2.2)

4. Connecting the power supply

Panel PC Remote Kit 43

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

Note

Information for the connecting elements can be found in chapter „Connection in the Instruction

manuals.

4.2. Connection of the Panel PC with the control unit

4.2.1. Interfaces of the remote device

Fig. 12: Location of the interfaces on the remote device

Description of the interfaces

DVI-D: will be connected with the DVI interface of the computer unit.

Note

The remote device is only able to operate with control unit of the Panel PC 677/877 and work

only with the suitable video signal.

USB-computer interface (> 5 m) Type RJ45:

will be connected with the USB transmitter for the distance larger than 5 m.

see chapter

4.2.4

USB -computer interface (up to 5 m) Type USB B:

will be connected with the computer unit for the distance up to 5 m. see

chapter 4.2.3

USB Interface Type USB A:

for external USB-devices

Attention!

Don’t use the USB interface combined with 19” Front if the ambient temperature is between

45 °C and 50 °C.

Panel PC Remote Kit 44

A5E00447267V Doc.No.:b40013de1.doc

Quick Start 08.07

Note

Don’t use a USB-HUB between the computer and the control unit.

Power supply:

The remote device will be delivered in two versions 24 VDC or

100-240 VAC.

For the 100-240 VAC version the power cable is supplied.

24 VDC has special connector; the label on the remote device describes

the pin setting. The pins are specified as follows:

Pin Signal Description

- GND Voltage input GND

+ +24 V Voltage input +24 VDC

4.2.2. Connecting of the control unit

Principle

The Panel PC Remote Kit version has the control unit and the computer unit in separate

location. The description of the computer interfaces can be found in instruction manual for

Panel PC.

Fig. 13: Control unit with mounted remote device

Mounting hole for

fixation of the cable

tie

Beim Panel PC mit Remote Kit sind Bedieneinheit und Recheneinheit räumlich

Panel PC Remote Kit 45

A5E00447267V Doc.No.:b40013de1.doc

Page is loading ...

Siemens SIMATIC 877 User manual

This manual is also suitable for

Siemens SIMATIC 877 User manual

in other languages

Related papers

Other documents