Miller HDC 1500DX CE Owner's manual

Brand: Miller

Model: HDC 1500DX CE

Category: Welding System

Type: Owner's manual

This manual is also suitable for

LK040136V

50, 60 Hz

Processes

Description

OM-212 296R

2009−01

Submerged (SAW) Welding

Submerged Arc Controller For

Automatic Welding

HDC 1500DX

File: SUBMERGED (SAW)

Visit our website at

www.MillerWelds.com

Miller Electric manufactures a full line

of welders and welding related equipment.

For information on other quality Miller

products, contact your local Miller distributor to receive the latest full

line catalog or individual specification sheets. To locate your nearest

distributor or service agency call 1-800-4-A-Miller, or visit us at

www.MillerWelds.com on the web.

Thank you and congratulations on choosing Miller. Now you can get

the job done and get it done right. We know you don’t have time to do

it any other way.

That’s why when Niels Miller first started building arc welders in 1929,

he made sure his products offered long-lasting value and superior

quality. Like you, his customers couldn’t afford anything less. Miller

products had to be more than the best they could be. They had to be the

best you could buy.

Today, the people that build and sell Miller products continue the

tradition. They’re just as committed to providing equipment and service

that meets the high standards of quality and value established in 1929.

This Owner’s Manual is designed to help you get the most out of your

Miller products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Miller you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will

help you figure out what the problem is. The

parts list will then help you to decide the

exact part you may need to fix the problem.

Warranty and service information for your

particular model are also provided.

Miller is the first welding

equipment manufacturer in

the U.S.A. to be registered to

the ISO 9001:2000 Quality

System Standard.

Working as hard as you do

− every power source from

Miller is backed by the most

hassle-free warranty in the

business.

From Miller to You

Mil_Thank 4/05

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1. Symbol Usage 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2. Arc Welding Hazards 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-3. Additional Symbols For Installation, Operation, And Maintenance 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-4. California Proposition 65 Warnings 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5. Principal Safety Standards 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-6. EMF Information 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-1. Symboles utilisés 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-2. Dangers relatifs au soudage à l’arc 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 7. . . . . .

2-4. Proposition californienne 65 Avertissements 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-5. Principales normes de sécurité 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2-6. Information EMF 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 3 − DEFINITIONS 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-1. Symbols And Definitions 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2. WEEE Label (For Products Sold Within The EU) 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 4 − SPECIFICATIONS 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-1. Weld Control 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-2. Description 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5 − INSTALLATION 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1. Typical Equipment Location 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2. Mounting Hole Layout 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-3. Typical Connection Diagram With Miller Power Sources 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-4. Left Side Panel Connections 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-5. Terminal Block TB1 And TB2 Connections 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-6. Terminal Block TB1 Connection Information 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-7. Terminal Block TB2 Connection Information 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-8. Connection Of 115 VAC Flux Hopper Without Plug 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-9. Remote 10 Receptacle RC2 Information 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-10. Remote 14 Receptacle RC1 Information 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-11. Remote 4 Receptacle RC3 Information 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-12. Remote Voltage Sense Leads Placement Guidelines For A Single Arc (Required) 20. . . . . . . . . . . . . . .

5-13. Remote Voltage Sense Leads Placement Guidelines For Multiple Arcs 21. . . . . . . . . . . . . . . . . . . . . . . . .

5-14. Power Source Selection Menu 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 6 − OPERATION 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-1. Safety Equipment 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2. Power Switch And Buttons 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-3. Program Push Buttons 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4. Front Panel Controls 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-5. Upper Display 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-6. Lower Display 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-7. Setup Push Button 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-8. Adjust Control 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-9. Sequence Push Button 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-10. Flux Push Button 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-11. Auxiliary Menus 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7 − REMOTE PROGRAM SELECT 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8 − MOTOR TYPES 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 9 − SETTING SEQUENCE PARAMTERS 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9-1. Sequence Parameters In A Program 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TABLE OF CONTENTS

SECTION 10 − MAINTENANCE & TROUBLESHOOTING 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-1. Routine Maintenance 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10-2. Circuit Breaker CB1 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 11 − ELECTRICAL DIAGRAM 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 12 − PARTS LIST 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

OPTIONS AND ACCESSORIES

WARRANTY

241813A

DECLARATION OF CONFORMITY

for European Community (CE marked) products.

MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that

the product(s) identified in this declaration conform to the essential requirements and

provisions of the stated Council Directive(s) and Standard(s).

Product/Apparatus Identification:

Product Stock Number

HDC 1500 DX 300438

Council Directives:

S 2006/95/EC Low Voltage

S 2004/108/EC Electromagnetic Compatibility

S 2006/42/EEC Machinery Directive

Standards:

S IEC 60974-1 Arc Welding Equipment - Welding Power Sources: edition 3, 2005-07.

S IEC 60974-5 Arc Welding Equipment – Wire Feeders: edition 1.1, 2002-02.

S IEC 60974-10 Arc Welding Equipment - Electromagnetic Compatibility Requirements: edition 1.1,

2004-10.

US Signatory:

November 25, 2008

__________________________________________________________________________

David A. Werba

Date of Declaration

MANAGER, PRODUCT DESIGN COMPLIANCE

Page is loading ...

OM-212 296 Page 1

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _2007−04

Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

. Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

1-2. Arc Welding Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-5. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic wire welding, the

wire, wire reel, drive roll housing, and all metal parts touching the

welding wire are electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

D Do not touch live electrical parts.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

D Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

D Use AC output ONLY if required for the welding process.

D If AC output is required, use remote output control if present on

unit.

D Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

D Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

D Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

D When making input connections, attach proper grounding conduc-

tor first − double-check connections.

D Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

D Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D If earth grounding of the workpiece is required, ground it directly

with a separate cable.

D Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

D Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

D Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

D Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

D Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists in inverter-type

welding power sources after removal of input

power.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

HOT PARTS can cause severe burns.

D Do not touch hot parts bare handed.

D Allow cooling period before working on gun or

torch.

D To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

OM-212 296 Page 2

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use local forced ventilation at the

arc to remove welding fumes and gases.

D If ventilation is poor, wear an approved air-supplied respirator.

D Read and understand the Material Safety Data Sheets (MSDSs)

and the manufacturer’s instructions for metals, consumables,

coatings, cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

D Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

D Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and while wearing an air-supplied

respirator. The coatings and any metals containing these elements

can give off toxic fumes if welded.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

ARC RAYS can burn eyes and skin.

D Wear an approved welding helmet fitted with a proper shade of fil-

ter lenses to protect your face and eyes when welding or watching

(see ANSI Z49.1 and Z87.1 listed in Safety Standards).

D Wear approved safety glasses with side shields under your

helmet.

D Use protective screens or barriers to protect others from flash,

glare and sparks; warn others not to watch the arc.

D Wear protective clothing made from durable, flame-resistant mate-

rial (leather, heavy cotton, or wool) and foot protection.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

D Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

D Do not weld where flying sparks can strike flammable material.

D Protect yourself and others from flying sparks and hot metal.

D Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

D Watch for fire, and keep a fire extinguisher nearby.

D Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

D Do not weld where the atmosphere may contain flammable dust,

gas, or liquid vapors (such as gasoline).

D Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock, sparks, and fire

hazards.

D Do not use welder to thaw frozen pipes.

D Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

D Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

D Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

D After completion of work, inspect area to ensure it is free of sparks,

glowing embers, and flames.

D Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL or DIRT can injure eyes.

D Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

D Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use

approved air-supplied respirator.

MAGNETIC FIELDS can affect Implanted

Medical Devices.

D Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

D Implanted Medical Device wearers should consult their doctor

and the device manufacturer before going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating

operations.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

D Wear approved ear protection if noise level is

high.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

D Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

D Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

D Keep cylinders away from any welding or other electrical circuits.

D Never drape a welding torch over a gas cylinder.

D Never allow a welding electrode to touch any cylinder.

D Never weld on a pressurized cylinder − explosion will result.

D Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

D Turn face away from valve outlet when opening cylinder valve.

D Keep protective cap in place over valve except when cylinder is in

use or connected for use.

D Use the right equipment, correct procedures, and sufficient num-

ber of persons to lift and move cylinders.

D Read and follow instructions on compressed gas cylinders,

associated equipment, and Compressed Gas Association (CGA)

publication P-1 listed in Safety Standards.

OM-212 296 Page 3

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near

combustible surfaces.

D Do not install unit near flammables.

D Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING UNIT can cause injury.

D Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

D Use equipment of adequate capacity to lift and

support unit.

D If using lift forks to move unit, be sure forks are

long enough to extend beyond opposite side of

unit.

OVERUSE can cause OVERHEATING

D Allow cooling period; follow rated duty cycle.

D Reduce current or reduce duty cycle before

starting to weld again.

D Do not block or filter airflow to unit.

FLYING SPARKS can cause injury.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

D Sparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

MOVING PARTS can cause injury.

D Keep away from moving parts.

D Keep away from pinch points such as drive

rolls.

WELDING WIRE can cause injury.

D Do not press gun trigger until instructed to do

so.

D Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

MOVING PARTS can cause injury.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors, panels, covers, or

guards for maintenance as necessary.

D Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read Owner’s Manual before using or servic-

ing unit.

D Use only genuine replacement parts from the

manufacturer.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified persons familiar with

electronic equipment perform this installation.

D The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa-

tion.

D If notified by the FCC about interference, stop using the

equipment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

D Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

D Be sure all equipment in the welding area is

electromagnetically compatible.

D To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

D Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

D Be sure this welding machine is installed and grounded

according to this manual.

D If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

OM-212 296 Page 4

1-4. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases

which contain chemicals known to the State of California to

cause birth defects and, in some cases, cancer. (California

Health & Safety Code Section 25249.5 et seq.)

Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

For Gasoline Engines:

Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproduc-

tive harm.

For Diesel Engines:

Diesel engine exhaust and some of its constituents are

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from Global Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1, from Global Engineering Documents (phone:

1-877-413-5184, website: www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, P.O. Box 9101, Quincy, MA 02269-9101 (phone:

617-770-3000, website: www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 4221 Walney Road, 5th Floor,

Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 5060 Mississauga,

Ontario, Canada L4W 5NS (phone: 800-463-6727 or in Toronto

416-747-4044, website: www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036–8002 (phone:

212-642-4900, website: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

P.O. Box 9101, Quincy, MA 02269-9101 (phone: 617-770-3000, web-

site: www.nfpa.org.

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(phone: 1-866-512-1800) (there are 10 Regional Offices—phone for

Region 5, Chicago, is 312-353-2220, website: www.osha.gov).

1-6. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

Welding current, as it flows through welding cables, will cause electro-

magnetic fields. There has been and still is some concern about such

fields. However, after examining more than 500 studies spanning 17

years of research, a special blue ribbon committee of the National

Research Council concluded that: “The body of evidence, in the

committee’s judgment, has not demonstrated that exposure to power-

frequency electric and magnetic fields is a human-health hazard.”

However, studies are still going forth and evidence continues to be

examined. Until the final conclusions of the research are reached, you

may wish to minimize your exposure to electromagnetic fields when

welding or cutting.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep welding power source and cables as far away from opera-

tor as practical.

5. Connect work clamp to workpiece as close to the weld as possi-

ble.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations.

If cleared by your doctor, then following the above procedures is recom-

mended.

Page is loading ...

OM-212 296 Page 9

2-5. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

de Global Engineering Documents (téléphone : 1-877-413-5184, site

Internet : www.global.ihs.com).

Recommended Safe Practices for the Preparation for Welding and Cut-

ting of Containers and Piping, American Welding Society Standard

AWS F4.1 de Global Engineering Documents (téléphone :

1-877-413-5184, site Internet : www.global.ihs.com).

National Electrical Code, NFPA Standard 70, de National Fire Protec-

tion Association, P.O. Box 9101, Quincy, MA 02269-9101 (téléphone :

617-770-3000, site Internet : www.nfpa.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chan-

tilly, VA 20151 (téléphone : 703-788-2700, site Internet :

www.cganet.com).

Code for Safety in Welding and Cutting, CSA Standard W117.2, de

Canadian Standards Association, 5060 Mississauga, Ontario, Canada

L4W 5NS (téléphone : 800-463-6727 ou à Toronto 416-747-4044, site

Internet : www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, de American National Standards Institute,

11 West 43rd Street, New York, NY 10036-8002 (téléphone :

212-642-4900, site Internet : www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, de National Fire Protection Association,

P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,

site Internet : www.nfpa.org).

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, de U.S. Government Printing Office, Superin-

tendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(téléphone : 1-866-512-1800) (il y a 10 bureaux régionaux−−le télépho-

ne de la région 5, Chicago, est 312-353-2220, site Internet :

www.osha.gov).

2-6. Information EMF

Considérations sur le soudage et les effets de basse fréquence et des

champs magnétiques et électriques.

Le courant de soudage, pendant son passage dans les câbles de sou-

dage, causera des champs électromagnétiques. Il y a eu et il y a encore

un certain souci à propos de tels champs. Cependant, après avoir exa-

miné plus de 500 études qui ont été faites pendant une période de

recherche de 17 ans, un comité spécial ruban bleu du National

Research Council a conclu : « L’accumulation de preuves, suivant le

jugement du comité, n’a pas démontré que l’exposition aux champs

magnétiques et champs électriques à haute fréquence représente un

risque à la santé humaine ». Toutefois, des études sont toujours en

cours et les preuves continuent à être examinées. En attendant que les

conclusions finales de la recherche soient établies, il vous serait

souhaitable de réduire votre exposition aux champs électromagnéti-

ques pendant le soudage ou le coupage.

Pour réduire les champs magnétiques sur le poste de travail, appliquer

les procédures suivantes :

1. Garder les câbles ensemble, les torsader, les scotcher, ou les

recouvrir d’une housse.

2. Disposer les câbles d’un côté et à distance de l’opérateur.

3. Ne pas courber pas et ne pas entourer pas les câbles autour de

votre corps.

4. Garder le poste de soudage et les câbles le plus loin possible de

vous.

5. Connecter la pince sur la pièce aussi près que possible de la

soudure.

En ce qui concerne les implants médicaux :

Les porteurs d’implants doivent d’abord consulter leur médecin avant

de s’approcher des opérations de soudage à l’arc, de soudage par

points, de gougeage, du coupage plasma ou de chauffage par induc-

tion. Si le médecin approuve, il est recommandé de suivre les

procédures précédentes.

OM-212 296 Page 10

SECTION 3 − DEFINITIONS

3-1. Symbols And Definitions

Amperes Remote Output

Hertz

Volts Input

Single Phase

Alternating

Current

Rated Welding

Current

Percent Circuit Breaker

Increase/Decrease

Of Quantity

Wire Feed Speed

Protective Earth

(Ground)

Postflow Timer Preflux Timer Start Time

Start Stop

Primary Voltage

Degree Of

Protection

Duty Cycle

Rated Supply

Current

Line Connection

Conventional Load

Voltage

On Off

Wire Feed Inch

Down

Wire Feed In Up

Crater Time Program Flux

3-2. WEEE Label (For Products Sold Within The EU)

Do not discard product (where ap-

plicable) with general waste.

Reuse or recycle Waste Electrical

and Electronic Equipment (WEEE)

by disposing at a designated collec-

tion facility.

Contact your local recycling office

or your local distributor for further

information.

OM-212 296 Page 11

SECTION 4 − SPECIFICATIONS

4-1. Weld Control

Specification Description

Type Of Input Power From Welding

Power Source

Single-Phase 115 Volts AC, 10 Amperes, 50/60 Hertz

Welding Power Source Type Constant Voltage (CV), AC Or DC

Welding Processes Submerged Arc (SAW) Welding

Overall Dimensions Including Knobs,

Receptacles, Etc.

Weld Control — Height: 11.5 in (292 mm); Width: 12.5 in (318 mm); Depth: 7 in (178 mm)

Weight Weld Control — Net: 25.5 lb (11.6 kg)

Weld Voltage And Amperage

Capacity (AC Or DC)

0 To 100 Volts

0 To 1500 Amperes

4-2. Description

This weld control is designed to au-

tomatically cycle welding events.

This unit can be used with constant

voltage, AC or DC welding power

sources. Relay contacts that work

in conjunction with the weld cycle

are available to interface with other

equipment (such as fixtures and

flux valves). See Section 5-5 and

5-7 for connection information on

TB2.

For information on the wire drive as-

sembly, see Owner’s Manual sup-

plied with the assembly.

803 448-A

OM-212 296 Page 12

SECTION 5 − INSTALLATION

5-1. Typical Equipment Location

Ref. 131 138-A

1 Welding Power Source

2 Side Beam

3 Weld Control

4 Spool Support

5 Wire Drive Assembly

6 Automatic Welding Gun

5-2. Mounting Hole Layout

Ref. 803 021-B

8 in

(203 mm)

10-3/4 in

(273 mm)

7 in

(178 mm)*

* Includes front panel knobs

5/16 in

Dia. 4 Holes

(7.9 mm)

OM-212 296 Page 13

5-3. Typical Connection Diagram With Miller Power Sources

. Customer must supply the following: power source, power source control cable, wire drive assembly, wire drive assembly cable, drive rolls, gun,

welding wire, weld cables, remote voltage sense leads and flux system for the desired application.

10-Pin Motor

Control Cord

14-Pin Welding

Power Source

Control Cord

4-Pin Flux

Valve Cord

Welding Cables

! Turn Off welding power

source and weld control

and disconnect input

power before making

connections.

. Use remote voltage sense

leads in all applications.

. Suggested size remote

voltage sense wire is 12

gauge or higher.

. See power source owners

manual for sense lead ter-

minal strip location and

connection.

HDC

FLUX

SYSTEM

FLUX

VALUE

WELDING

POWER

SOURCE

WORKPIECE

WIRE

DRIVE

ASSEMBLY

1500DX

Remote Voltage

Sense Leads

(+) Electrode Stud

(−) Work Stud

DCEP (Reverse Polarity) Connection

. For DCEN (straight polarity) observe sense

lead relationship with power source output

polarity. Example - N to (−) or work output stud

and P to (+) or electrode output stud.

OM-212 296 Page 14

1 Receptacle

2 Keyway

3 Access Hole - For Customer

Use: Connections To Terminal

Blocks, Flux Valve, etc.

! Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

. Install strain relief (customer

supplied) in access hole.

Route incoming cables through

user access hole prior to making

connections to internal terminal

blocks.

4 4-Pin Receptacle:

Connection To Flux

Hopper/Shielding Gas Valve.

5 14-Pin Receptacle:

Connection To Welding Power

Source.

6 10-Pin Receptacle:

Connection to Wire Drive

Motor

To connect matching interconnect-

ing cord to one of the above

receptacles, align keyway, insert

plug, and tighten threaded collar.

Connect remaining end of cord to

matching receptacle on applicable

equipment.

5-4. Left Side Panel Connections

1 2

Ref. 803 449-B

Example Receptacle

RC2RC1RC3

OM-212 296 Page 15

5-5. Terminal Block TB1 And TB2 Connections

Ref. 803 450-B

! Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

1 Access Door

Remove securing screw and open

access door.

2 Terminal Block TB2

3 Terminal Block TB1

4 Securing Screw - Terminal

Block

5 Stripped Lead

6 Typical Lead Being

Connected To Terminal Block

7 Access Hole - Used For

Connections To Terminal

Blocks, Flux Valve, etc.

. Install strain relief (customer

supplied) in access hole.

Strip 1/4 in (6 mm) insulation off end

of lead, insert end into proper loca-

tion on TB1 and TB2. Tighten appli-

cable securing screw.

Close and secure access door.

Tools Needed:

1/4 in

(6 mm)

OM-212 296 Page 16

5-6. Terminal Block TB1 Connection Information

Terminal/Number Receptacle Location Function Information

A A on 14-Pin

A normally open set of relay contacts connect terminal A to terminal B when

Start is pressed and pre-flux timer times out (contacts are rated 10 amperes, 125

volts AC).

B B on 14-Pin

C C on 14-PIn Remote command reference from welding power source.

D D on 14-Pin Remote circuit common.

E E on 14-PIn Output command to welding power source (0 to 10 volts DC).

G G on 14-PIn Circuit common for 24 and 115 volts AC circuits.

I I on 14-PIn 115 volts AC from welding power source, which is present whenever welding

power source is on.

F F on 14-PIn Current feedback input (1 volt DC per 100 amperes).

H H on 14-PIn Voltage feedback input (1 volt DC per 10 arc volts).

K K on 14-PIn Chassis common.

Remote Stop When connected to remote common, stops the weld cycle.

Remote Jog Down When connected to remote common, jogs wire down.

Remote Common Circuit common for remote capabilities.

5-7. Terminal Block TB2 Connection Information

Terminals Function Information

Red 115 volts AC to power flux hopper.

Black Switched 115 volts AC to power flux hopper.

White Circuit common for 115 volts AC for flux hopper.

Green Chassis common for flux hopper.

Side Beam 1 Relay Normally open set of contacts* that close when the Start button is pressed or after a set time after the arc has

been established (see Section 6-11). Contacts open again when the Stop button is pressed.

Side Beam 2 Relay Normally open set of contacts* that close when an arc is established. These contacts are used when you want

the side beam to start moving once an arc has been established. Contacts open again when the Stop button is

pressed.

Remote Start When connected to remote common, starts the weld cycle.

Remote Jog Up When connected to remote common, jogs wire up.

Remote Program When connected to remote common, increments the program.

* NOTE: All contacts are rated 10 amperes, 125 volts AC.

OM-212 296 Page 17

5-8. Connection Of 115 VAC Flux Hopper Without Plug

Ref. 803 629-A

! Turn Off welding power

source and weld control and

disconnect input power be-

fore opening access door.

1 Access Door

Remove securing screw and open

access door.

2 Terminal Block TB2

3 Access Hole - Used For

Connections To Terminal

Blocks, Flux Valve, etc.

. Install strain relief (customer

supplied) in access hole.

Strip 1/4 in (6 mm) insulation off end

of leads. Insert four-conductor

cables from flux system through ac-

cess hole, and make connections

as shown.

Close and secure access door.

Tools Needed:

Four-Conductor Cable

From Flux System

Green Lead

White Lead

Black Lead

Red Lead

Four-Conductor Cable

From Flux System

OM-212 296 Page 18

5-9. Remote 10 Receptacle RC2 Information

REMOTE 10

Socket Socket Information

Wirefeed Drive

Motor Hookups

A To positive (+) motor armature (115 volts DC motor).

B To negative (−) motor armature (115 volts DC motor).

C To motor field.

D To motor field.

E Chassis common.

F Tachometer feedback; 0 to +12 volts DC.

G 12 volts DC to power tachometer

H Circuit common for +12 volts DC circuit.

I Not used.

J Not used.

10 Pin Motor Cable

Ref. 212 591-A

5-10. Remote 14 Receptacle RC1 Information

Socket

User Accessible

Via TB1

Terminal #

Socket Information

Contactor Control

A A

24 volts AC or 115 volts AC from welding power source (present

whenever power source is On).

B B

Normally open set of relay contacts connect A to B when Start is

pressed and preflux timer has timed out.

Remote Output Control

C C Remote command reference from power source; +10 volts DC.

D D Remote circuit common.

E E Output command signal to power source; 0 to +10 volts DC.

Amperage/Voltage Feedback

F F

Current feedback input from power source; +1 volt DC per 100 am-

peres.

H H

Voltage feedback input from power source; +1 volt DC per 10 arc

volts.

Electrical Input Power

G G Circuit common for 24 and 115 volts AC circuits.

I I

115 volts AC from welding power source (present whenever welding

power source is on). 115 volts AC is present on terminal block TB1

whenever welding power source is on.

GND

K K Chassis common.

14 Pin Interconnecting Cable

Ref. 178 836

OM-212 296 Page 19

5-11. Remote 4 Receptacle RC3 Information

Socket

User Accessible

Via TB2

Terminal #

Socket Information

Flux Hopper Hookups

A Red 115 volts AC to power flux hopper.

B Black Switched 115 volts AC to power flux hopper.

C White Circuit common for 115 volts AC for flux hopper.

D Green Chassis common for flux hopper.

4 Pin Flux Hopper Cable

Ref. 300 484-A

Notes

Page is loading ...

Miller HDC 1500DX CE Owner's manual

Brand: Miller

Model: HDC 1500DX CE

Category: Welding System

Type: Owner's manual

This manual is also suitable for

LK040136V

Download PDF

report

in other languages

français: Miller HDC 1500DX CE Le manuel du propriétaire

Miller HDC 1500DX CE Owner's manual

This manual is also suitable for

Miller HDC 1500DX CE Owner's manual

in other languages

Other documents