Sanyo ECD-HI340 Operating Instructions Manual

OPERATING

INSTRUCTIONS

ECD-HI340

AM/FM Stereo Radio CD Player

with Full Detachable Panel,

1.5 Din Size

Multi-color LCD Display

CONTENTS

Accessories _- __________________ -_---- __________________ -------_- ________________ 1

Compact Disc Care __....._________________________________------ -------- ______ 2

Installation __--- ______________ --- _____________________ ----------_- ____________... 3

Using the Detachable Front Panel _________..____________________ -_-- ______ 4 - 5

Electrical Connections __----- _________________ ----- _________________....... 6 - 7

Location and Function of Controls ________________ ----- ____ ______________ 8 - 10

Specification ______________ -- __________________ ----- __________________.._______ 11

Trouble Shooting _______________________________________ ----- _________________ 12

Warranty ____ -- _________________ --- __________________ --- ___________________..... 13

ACCESSORIES

Please retain the carton and packing materials, as this is the best protection for the

unit should it be necessary to return it for servicing

Check the packing carefully for the following accessories

(1) 1 x l#mounting bracket (used to fix unit to car, see installation method B)

(2) 2 x 2#mounting bracket (used to fix unit to car, see installation method B)

(3) 1 x 3#mounting bracket (used to fix unit to car, see installation method B)

(4) 1 x right bracket (used for “GM” car)

(5) 1 x left bracket (used for “GM” car)

(6) 8 x screw 3x4mm

(used to fix mounting bracket (l#, 2#, 3#) to unit, see installation method B)

(7) 4 x quickie bolt 5x1 Omm (used to fix unit to car, see installation method A)

(8) 1 x quickie bolt 5xl8mm (used to fix unit to car, see installation method A)

(9) 1 x screw 2xl2mm (used to secure the front panel for anti-theft purposes)

(10) 5 x hexagon nut (used to quickie bolt)

(11) 4 x screw 4x1 Omm (used to right/left bracket)

6) (4& t2) 6 t3) & 14) @

1 #mounting bracket 2#mounting bracket 3#mounting bracket right bracket

(5)

(6)

(7)

03)

@m

left bracket screw quickie bolt quickie bolt

(9) (10) (11)

a3

&

screw hexagon nut screw

CAUTION

l This unit is designed to operate on 12 volts DC, negative ground electrical systems

only

l When fuse replacement is necessary, use only a 15 amp fuse

Do not replace with

a higher rated fuse If the fuse blows often, carefully check all electrical connections

for any short circuits and have your car’s voltage regulator checked also

l Do not install the unit where it will be exposed to direct sunlight or hot air discharged

from the car heater

l Do not expose the unit to water or moisture

l This AM/FM Radio with CD Player should not be adjusted or repaired by anyone

except qualified service personnel If servicing is required, return the unit to an

authorized SANYO mobile audio dealer

l Changes or modifications not expressly approved by SANYO may void the user’s

authority to operate this equipment

l This device complies with Part 15 of the FCC Rules Operation is subject to the

following two conditions

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation

1

COMPACT DISC CARE

Dust, dirt, scratches or warpage can cause a deterioration in the sound, or intermittent

skipping of some tracks during play

I

DIGITAL AUDIO

l This unit has been designed to play

1

compact discs bearing the

identification logo shown on the left

No other discs can be played

l Fingerprints and dust should be

carefully wiped from the signal

surface of the disc (glossy side) with

a soft cloth

l Wipe in a straight motion from the

inside to the outside of the disc

Unlike conventional records, the

compact disc has no grooves to

collect dust and debris Small dust

particies will have no effect on

reproduction quality

l Do not insert a disc which is cracked

into the unit

l Do not apply paper or write anything

on the surface of the disc

l To prevent warping the disc, do not

expose it to direct sunlight, high

humidity or high temperatures for

extended periods

l The unit may not operate properly if

condensation occurs Wait for 1 or 2

hours (to allow the internal parts to

adjust to the surrounding

temperature) before using the unit

l When not using the disc player for

extended periods of time, remove the

compact disc and return the plastic

disc from dust and exposure to the

2

INSTALLATION

Method A

SUB PANEL

‘_ FLANGE NUT

PANEL

Method B

\

QUlCw; BOLT x

MOUNTING

SCREW

P#BFsACKET

PANEL

luAEfKET dJfy ,~ m,janncKr

l#BPaACKET P#BRACKET P#BPnACKET D

tTANDARD MOUNTING CONFIGURATION “JA” MOUNTING CONFIGURATION

“Jz” MOUNTING CONFIGURATION

3

USING THE DETACHABLE FRONT PANEL

To Detach the Front Panel

1 Press the release button (REL), then the right-hand side of the panel will be ejected

2 Remove the front panel by pulling its right-hand side outward

/

3 For safekeeping, store the front panel in the supplied protective case immediately

Protective case

To Reinstall the Front Panel

1 Push the front panel into the main body A ‘click’ sound should be heard

2 Note that if the front panel fails to lock in position properly, pushing the release

button may not release the panel, and the other control buttons may not function

Precautions when Handling

1 Do not drop the front panel

2 Do not put pressure on the display or control buttons when detaching or reinstalling

the front panel

3 Do not touch the contacts on the front panel or on the main unit body It may result

in poor electrical contact

4 If any dirt or foreign substances adhered on the contacts, they can be removed

with a clean and dry cloth

5 Do not expose the front panel to high temperatures or direct sunlight

6 Keep away any volatile agents (e g benzene, thinner, or insecticides) from touching

the surface of the front panel

7 Do not attempt to disassemble the front panel

I

ELECTRICAL CONNECTIONS

I

WIRING FOR ECD-HI340

I .II -----

4-speaker System _ _ _ _ , _ _ _ _ _ _ P-speaker System _ _ _ _ _

,

slack) emSpeaker I ;

(White/Black) 8 &=

- n Front Left i !

CB

g

n Front Riaht I I

(White)@&

,

=@I

Left I

--

Speaker ,

(Gray) CB 8

I

- - A Riaht ,

1 (Gray/Black) em Speake;

Ireen) $ @

Rear Left

Eew Speaker

Speaker j

00 not 1

Connect I

Do not I

Connect I

11111

--------------------__I

+12V Constant Power Supply (yellow)

fkignd

+12V Accessory/Switched (Red)

Wire (Black)

111 Power Antenna/Amplifier Turn On (Blue/Red)

Caution

l DO NOT connect any speaker wires to the metal body or chassis of the vehicle

l Connect each speaker wire directly to each speaker terminal

l All speaker common (-) wires must remain floating

1

Antenna socket

l Insert the plug from the antenna installed in your vehicle into this socket (if your

vehicle has a dual antenna system, a dual antenna to single antenna cable

adaptor may be required )

2

+12V Constant Power Supply (Yellow)

l Connect this wire to the +12V power terminal which receives power continuously

3 +12V Accessory/Switched (Red)

l Connect this wire to the terminal which receives power while the ignition switch

is ON or in the ACCESSORY position

l If the ignition switch does not have an ACC position, connect this wire to a +12V

power terminal which receives power continuously (Same as item 2 )

4 Ground wire (Black)

l Connect this wire to the vehicle chassis

5 Power Antenna/Amplifier Turn On (Blue/Red)

l Connect this wire to the control terminal of a Power Antenna or an external

amplifier

l When not using a Power Antenna or an external amplifier, this wire is not

connected

6

Notes

- When using a two-speaker installation, the Green, Green/Black, Violet and

Violet/Black wires, which are used for a four-speaker installation, are not used

Cover the ends of these wires with electrical tape to prevent them from shorting to

the unit or the vehicle chassis

- When using a two speaker installation, set the FADER control to the center position

- When fuse replacement is necessary, remove the blown fuse by opening the Filter

Box , then install a new 1 amp fuse (switched power supply) or 15 amp fuse

(constant power

supply)

I

FILTER BOX

- RCA Line Out Jacks

Connect a patch cable (not supplied) from the White (left rear channel) and Red

(right rear channel) RCA line output jacks to the line input terminals of an external

amplifier

CAUTION -USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE

THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY

ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL

This compact Disc Player is made and tested to meet exacting safety standards It

meets FCC requirements and complies with safety performance standards of the U S

Department of Health and Human Services

THIS PRODUCT COMPLES WITH DHHS RULES 21 CFR

SUBCHAPTER J PART 1040 IO AT DATE OF MANUFACTURE

7

LOCATION AND FUNCTION OF CONTROLS

1. ON/OFF

Press POWER button (1) to turn on

Press POWER again to turn it off If the

power is off, press BND button (12) or MOD button (13) also can turn on the unit

2. DISC PLAY

Gently insert a compact disc with the label side facing up into the disc slot (2)

The disc is then automatically loaded into the unit and starts playing with the first

track of the disc The digital display will indicate the track number

3. MUTE

Press the MUT button (3) to silence the receiver Press again to resume listening

8

4. MONO/STEREO

Press MON button (4) to select monaural or stereo (Mono reception for radio

stations) You can sometimes improve reception of distant stations by selecting

mono operation

5. FACEPLATE RELEASE

Press REL button (5) to detach the removable faceplate

6. LOUDNESS

Press LOU button (6) to increase bass output and display will show “LOUD”

7. SET THE CLOCK

Press and hold the DSP button (7), then press the TUNE/SKIP + /b> button (16)

to change minutes or TUNE/SKIPd - button (15) to change hours

8. EJECT

Push a CD into slot The CD will begin to play Press P (eject) button (8) to stop

CD play and eject CD from slot Receiver switches to radio operation

9 &IO. SELECT MODE

Press PUSH SELECT button (9) to move display through bass, treble, balance,

fader and volume functions Use AUDIO ADJUST KNOB (10) to adjust the

selected mode When mode has not been adjusted for several seconds, display

returns to normal radio or CD display

BAS --) TRE --) BAL --, FAD ----) VOL

(Bass) (Treble)

(Balance) (Fader) (Volume)

1

Bass

Press PUSH SELECT button (9) one time Adjust bass level by rotating AUDIO

fDD;ST KNOB (10)

Press PUSH SELECT button (9) two times Adjust treble level by rotating AUDIO

;,9Ja;lz; KNOB (10)

Press PUSH SELECT button (9) three times Adjust sound balance between left

;n,dd;rht speakers by rotating AUDIO ADJUST KNOB (10)

Press PUSH SELECT button (9) four times Adjust sound balance between front

and rear speakers by rotating AUDIO ADJUST KNOB (10)

Volume

Press PUSH SELECT button (9) five times Adjust volume level by rotating AUDIO

ADJUST KNOB (10)

11. EQUALIZATION

Press EQ button (11) to turn on equalization function and to select desired audio

mode There are four kinds of mode as below

r

FLAT - ROCK - CLASSIC - POP

1

12. BAND

Press BND button (12) to change between three FM bands and two AM bands

Each band stores up to six preset stations

r

FM1 ----) FM2 ---) FM3 4 AM1 --) AM2

1

I

13. ELECT LISTENING MODE

Press MOD button (13) to choose desired listening mode

(e g radio mode to CD mode)

9

14. LIQUID CRYSTAL DISPLAY

The LCD (14) can show the current state of the unit

15 & 16. SELECT STATIONS

Press and release a TUNE/SKIPd - button (15) or TUNE/SKIP + /B button (16)

immediately to move radio frequency number down or up on step

Press and hold a TUNE/SKIPd - button (15) or TUNE/SKIP + /D> button (16)

for several seconds to seek the next clear station

15 & 16. SKIP TRACKS

Press a TUNE/SKIPd - button (15) or TUNE/SKIP + /W button (16) to move to

the previous track or the following track

Track number shows on the display

15 & 16. FAST FORWARD AND FAST REVERSE

17.

16.

19.

20.

21.

22.

23.

Press a TUNE/SKIP<=I/ - button (15) or TUNE/SKIP + /p.> button (16) to fast

reverse or fast forward CD play starts from when you release the button

PRESET STATIONS

Six number buttons (17) store and recall stations for each band

Store a station

Select a band (12) (if needed) Select a station Hold a preset button for several

seconds

Recall a station

Select a band (12) (if needed) Press a preset button to select stored station

TOP: PLAY THE FIRST TRACK

Press TOP button (18) to play the first track of the current disc

REPEAT THE SAME TRACK

Press RPT button (19) to continuously repeat the same track Press again to stop

repeat

INTRO: PREVIEW ALL TRACKS

Press SCN button (20) to play first several seconds of each track on the current

disc Press again to stop intro and listen to track

RANDOM: PLAY ALL TRACKS

Press RND button (21) to play all tracks on CD in random

Press again to cancel

the function

AUTOMATICALLY STORING & PROGRAM SCANNING

Automatically Storing

Press and hold AS/PS button (22) for several seconds to toggle automatically

storing function It starts searching next frequency and stores the clear station

into the preset memory At the end of automatically storing operation, mode is

changed to Preset Scan

Preset Scanning

Press ASIPS button (22) shortly to toggle preset scanning function During the

scanning, it will stop at every stored station for several seconds and the number

of the channel being scanned flashes on the display Press it again to stop

scanning

RESET BUTTON FUNCTION

RESET button (23) is placed on the housing and must be activated with either a

ball point pen or thin metal object The reset button is to be activated for the

following reasons

l Initial installation of the unit when all wiring is completed

l All the function buttons do not operate

l Error symbol on the display

Note: If RESET button (23) is pressed and the unit doesn’t work yet, please use

a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the

front panel

10

MODEL ECD-HI 340 SPECIFICATIONS

FM TUNER SECTION

Frequency Range . . ..__-...._----._------------------------ 87 5 MHz - 107 9 MHz

Usable Sensitivity . . . . _. . . . _ _ _ . . _. . __ _ __. . __ _. . . . . . . 17 23 dBf

50 dB Quieting Sensitivity . . . . . . . . . . . . . ..__. . . ..__ . ..__ 20 76 dBf

Frequency Response ---__------------.-------------------~------~~ 40 Hz - 12 KHz

I F Response Ratio .___-_..__----.___----~--------------------------------~~. 80dB

ImageResponseRatio -_----- ____ ---- __.. -- ___...___......__................ 50dB

Signal-to Noise Ratio -------------------______ ____ -- _______ ___....___...... 60 dB

Alternate Channel Selectivity ___.. - ___....____.... ._.... . . . . . . . . . . . 50 dB

Stereo&par&ion __----___-------------------------------~------~~~----~~~.- 30dB

CaptureRatio ___....__ -- . . .._ --- _.._ -----_--------------------------------~~ 15dB

Antenna Impedance ----__--------------------------------~------~~-----~~..~~ 75Q

AM TUNER SECTION

Frequency Range ------_------__.--- ___.. -- __.....___........ 530 KHz - 1710 KHz

UsableSensitivity(S/N20dB) ----------__----- ____ --- ____. ____....___....._ 2OpV

I F. Response Ratio -----__-------_------------------------~------~~~-----~~.. 60dB

Image Response Ratio --.._-----___------------------------------~~---~~~~.~ 36dB

Signal-to-NoiseRatio --_-------__---- __.._ -- _-__..___.....___..............- 50dB

Antenna Impedance -----------__----- __.. -- ___...____....._................... 75Cl

COMPACT DISC SECTION

DiscSize ----------------------------------------~.-----~~~-----~~~---~~~...~~~. 5”

Sampling Frequency --------------------_____________ ____._ - ____... -- __... 44 1 KHz

Digital Filter -----------__-------_____ ___.. --- ___...____....___.... 8xOversampling

Digital-to-Analog Converter -----_-------_-------~~--- ______ -- ____.. -__ Single, l-Bit

Pickup ____.....__......__................... Optical 3-Beam Semiconductor Laser

Output Filter ._--...__---_..~_----~~~------~--------------------------------- Active

AUDIO SECTION

Maximum Power Output --------------------------------~~------~~~----~~~ 40W x4

Load Impedance . ..___._..___...___.... .___..... . . . . . . . . . . . . .._.... 4Q

GENERAL

OperatingVoltage ..____....__ ---.__----- ____ -----__-------_---- 12V(144VTypical)

Operating Current Maximum _ _. . - -_ _ _. . . - _. . . _ _ _. . . . . ._ _. . . . _. . . . . . .15A

lnstallationsize(WxHxD) ---___----- ____ ---- __.. --- ___... -__ 200x785x142mm

IMPORTANT INFORMATION

Because its products are subject to continuous improvement, SANYO reserves

the right to modify product designs and specifications without notice and without

incurring any obligation

11

I

TROUBLE SHOOTING

~~~ 1

Before going through the check list, check wiring connection

If any of the problems

persist after check list has been made, consult your nearest service dealer

Symptom Cause

No power The car ignition is not on

Solution

If the power supply is properly

connected to the car accessory

terminal, switch the ignition key to

“ACC”

The fuse is blown Replace the fuse

Disc cannot Presence of CD disc

Remove the disc in the player, then

be loaded or inside the player

put a new one

ejected

Inserting the disc in

Insert the compact disc with the

reverse direction label facing upward

Compact disc is extremely Clean the disc or try to play a new

dirty or defective disc one

Temperature inside the Cool off or until the ambient

car is too high temperature return to normal

Condensation

Leave the player off for an hour or

so, then try again

No sound Volume is in minimal

Wiring is not properly

connected

Adjust volume to a desired level

Check wiring connection

The operation The built-in microcomputer Press the RESET button

keys do not is not operating properly Front panel is not properly fixed into

work due to noise its place

Sound skips The installation angle is Adjust the installation angle to less

more than 30 degrees than 30 degrees

The disc is extremely dirty Clean the compact disc Then try to

or defective disc play a new one

The radio does The antenna cable is not Inset-t the antenna cable firmly

not work The connected

radio station

automatic

The signals are too weak Select a station manually

selection does

not work

12

SANYO MOBILE AUDIO

MODEL ECD-H1340 LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized

Sanyo Factory Service Center at the user’s expense, unless specifically stated otherwise in this

warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling

the toll-free number listed below

For product operation, authorized service center referral, service assistance or problem resolution, call

CUSTOMER INFORMATION l-800-421-6382

Weekdays 8~00 AM - 500 PM Pacific Time

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE

UNITED STATES OF AMERICA

THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER, AND DOES NOT APPLY TO

PRODUCTS USED FOR ANY INDUSTRIAL, PROFESSIONAL OR COMMERCIAL PURPOSE THE

ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE SUBMITTED TO THE AUTHORIZED

SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY (SFC)

warrants this SANYO product against defects in materials and workmanship for the periods specified

below SFC will repair or replace (at its option) the product and any of its parts which fail to conform

to this warranty with new or reconditioned products or parts The warranty period commences on the

date the product was first purchased at retail

LABOR PARTS

1 YEAR 1 YEAR

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the

appropriate model’s instruction manual, or(B) the repair of any product whose serial number has been

altered, defaced or removed

This warranty does not apply to the cabinet or cosmetic parts, knobs or routine maintenance

This warranty does not apply to the elimination of car static or motor noise, correction of antenna

problems, or damage to compact discs, speakers, accessories or vehicle electrical systems

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control

of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from

unauthorized service or parts, improper maintenance, operation contrary to furnished instructions,

shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident,

incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear

The foregoing is in lieu of all other express warranties and SFC does not assume or authorize any party

to assume for it any other obligation or liability

THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY

IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE

PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS

CONTROL

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS

AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO

THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS, WHICH

VARY FROM STATE TO STATE

For your protection in the event of theft or loss of this product, please fill in the information below for

your own personal records

Model No Serial No

Located on back or bottom side of unit)

Date of Purchase Purchase Price

Where Purchased

13

21605 Plummer Street

Chatsworth, CA91 311

ECD-HI340 Issue Number 1

Printed in Hong Kong

88.CO602-03

Sanyo ECD-HI340 Operating Instructions Manual

This manual is also suitable for

Sanyo ECD-HI340 Operating Instructions Manual

Related papers

Other documents