MAGNUM FIRST M9-ML2 Installation guide

Brand: MAGNUM FIRST

Model: M9-ML2

Type: Installation guide

MAGNUM FIRST M9-ML2 is a wireless, self-powered, passive infrared sensor that ensures reliable detection of occupant presence. It's ideally suited for occupancy-based lighting control and indoor daylight harvesting, with a light range of 0-1020lx. When paired with a relay and a wireless rocker switch, it creates a cost-effective lighting control system. It can also be integrated into a BACnet-compatible building automation system when combined with a Magnum gateway.

Magnum First - 1 Seneca Street, 29th Floor, M55 - Buffalo, NY 14203 - phone 716-293-1588 - www.magnumfirst.com - [email protected]

Product Installation Guide

Motion / Lux Sensor

M9-ML2

1] Description

6] Dimensions

7] User Instructions

2] Operation

5] Technical Speciﬁcations (continued)

The Magnum Innovations Motion and Lux sensor (Mx-ML2) is a wireless, self powered, passive infrared sensor

that ensures reliable detection of occupant presence. The Mx-ML2 is ideally suited for occupancy based lighting

control and also provides for indoor daylight harvesting functionality, with a light range of 0-1020lx. When paired

with a relay (Mx-USR-L1) and a wireless rocker switch (Mx-ESRP), the sensor creates an out of the box, cost eective,

lighting control system. When combined with an Magnum gateway (Mx-EBOX), the Mx-ML2 can be integrated into

an existing BACnet-compatible building automation system.

Built in solar cells draw and store energy from available ambient light to power the device and keep it operational

during periods of darkness. The device must be placed at the location where sensing is required and this location

is dependent on individual application (refer to Sensor Placement Tips below). An optional battery back up is

available for locations with low or no ambient light. The Mx-ML2 must be paired with a receiver (refer to Compatible

Devices section). The device can be paired manually to compatible devices by pressing the LRN button while

following the pairing instructions for the receiver. For more sophisticated configuration, please refer to the MES

AirConfig tool (email [email protected] for download instructions) .The sensor can be mounted using

screws or simply placed in selected location with double stick tape. It is recommended that the pairing of this

device be done prior to installing the ceiling sensor.

4] Applications

• Hotels & Resorts • Private Oces • Colleges & Universities

• Retroﬁts • New Construction • Conference Rooms

• Executive Oces • Classrooms • Lighted Hallways

• Perimeter Zones • Cruise Ships • Daylight Harvesting

• Restrooms • Daycare Facilities • And more..

Light Sensor 0-95 FC (0-1020 Lux)

Default Transmission Interval Immediate upon detected occupancy

(Status signal sent every 15 minutes)

Default Unoccupied Send Delay 5 minutes (Adjustable via airConﬁg Tool*)

Minimum Light Required to Charge 4FC (40 Lux)

Minimum Charge Time to Begin Operation 1 minute @ 20FC (200 Lux)

Full Charge Time 8 hours (approx) @100FC (1000 Lux)

Maintain Charge Time 3 hours per 24 hours @ 20FC (200 Lux)

Operation Life at Full Charge (no battery) up to 72 hours

Optional Battery Life 10 years (1/2AA 3.6V Lithium)

Operating Temperature -3°F to 140°F (20°C to 60°C)

Detection Distance (PIR Sensor) 39 ft (12 m)

Detection Range (Horizontal & Vertical) (PIR Sensor) 102° x 92°

3.17” (80.52 mm)

2.96” (75.18 mm)

4.02” (102.11 mm)

5] Technical Speciﬁcations:

Part Numbers (Frequency Dependant) M9-ML2 (902 MHz - North America)

M8-ML2 (868 MHz - Europe and China)

MJ-ML2 (928 MHz - Japan)

Range 150 feet (50-150 typical)

EnOcean Proﬁles A5-07-03 (Default) - Occ, Supply Voltage, Illumination 0-1000lx

F6-02-01 - Rocker On/O, Occ Only

A5-06-02 - Illumination 0-1020lx only

A5-07-01 - Occ, Supply Voltage

A5-07-02 - Occ, Supply Voltage

A5-08-01 - Occ, Supply Voltage, Illumination 0-510lx

A5-08-02 - Occ, Supply Voltage, Illumination 0-1020lx

A5-08-03 - Occ, Supply Voltage, Illumination 0-1530lx

To select profiles other than default, utilize the

MES software for configuration “AirConfig Tool*”.

(email [email protected] for

download instructions)

UPON RECEIVING ML2 FOLLOW STEPS BELOW..

1) Insert provided battery into the ML2

2) To ensure proper operation of the device, press and release the learn button and you should see the LED ﬂash once

3) Repeat Step 2 twice for a total of 3 times

4) If the LED does not ﬂash, remove the battery and wait 5 seconds. Then reinstall the battery and repeat Step 2

5) The device is now ready for pairing if so desired

FOR BATTERY FREE OPERATION, place the device under bright light for 8 hours to attain a full charge before operating

PAIRING LRN Button

Press and release the LRN button. The red LED light should

ﬂash once, signaling the device has sent a “learn” message to

identify itself with compatible devices within wireless range

Please refer to the corresponding device installation guides to

review the process of learning this sensor with compatible devices.

NOTE: It is recommended that pairing of device be done prior to installing the ceiling sensor

NOTE: Use a non-metalic pin when pressing the Learn Button

Light Sensor

LED

Magnum First - 1 Seneca Street, 29th Floor, M55 - Buffalo, NY 14203 - phone 716-293-1588 - www.magnumfirst.com - [email protected]

Product Installation Guide

11] Sensor Placement

12] Troubleshooting

13] Warranty

Classroom Hotel Room

Sensor Placement Tips:

1) Do not mount sensor near obstacles that could potentially block sensor’s line of sight.

2) Keep sensors 10-15ft away from heating vents and radiators. If a sensor detects a rapid change in heat, it could

inaccurately detect occupancy.

3) If mounting on a wall or in a corner (anywhere other than ceiling) aim sensor towards the likely entry point.

4) If sensor is to be used to control lights based on occupancy and perform daylighting controls, and there

is a question related to appropriate placement, please refer to the guidance herein or call tech support at

330.656.9365.

NOTE: remember this device is charged and operates using the light in the room, if there are several mounting

location choices, choose the brightest option.

1) Verify the LED ﬂashes when the LRN button is pressed and released

2) If the LED light does not blink, check to see if the device is equipped with a back up battery

3) If the device has no back up battery, place the sensor under light, allowing it to charge

4) If the LED still does not ﬂash after the LRN button is pressed and released, the sensor could be defective.

5) If the device includes a back up battery, then the battery might need to be replaced.

U.S. Two-year Limited Warranty: Products purchased in the U.S.A. are warranted for two years from date of purchase

by Magnum Innovations to be free of defects in materials and workmanship. In the event of such defect, product

will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value

if delivered to Magnum or an Authorized Service Center, prepaid, together with the sales slip or other proof of

purchase date. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use

product in accordance with instructions. This warranty is void in the event of unauthorized repair or modiﬁcation,

or removal or defacing of the product labeling. The Magnum warranty speciﬁed herein covers material only and

does not include labor or incidental costs associated with product replacement or repair.

10] Coverage

9] Mounting

Image 1 Image 2 Image 3 Image 4

Ceiling Mount (With Screws):

1) Mount backplate to ceiling with the four provided screws (see Image 1)

2) Attach the body of the sensor to the backplate by rotating until locked into place (see Images 2-4)

Ceiling Mount (With Tape:

1) Peel layer o double stick tape and place one side onto back of sensor housing.

2) When ready to place, peel other layer o tape and ﬁrmly push motion sensor onto surface and hold for 30-60 seconds.

8] Compatible Devices

• M9-TS1 (24V Intelligent Thermostat with 4.3” LCD) • M9-PFC-EO2036 (Line-Voltage Thermostat)

• M9-PFC-EO2037 (24V Thermostat) • M9-USR-L1 (Single Channel Lighting Control Module)

• M9-UTR-L1 (Two Channel Lighting Control Module) • M9-eBox (BACnet IP Gateway)

• M9-AP2 (Access Point) • M9-ILS2 (Integrated Light Switch)

Side View 1

Top View

Side View 2

Long Distance Detection Type

102° 92°

12m

39 ft

33.1m

108 ft

27.8m

91 ft

11.6m

38 ft

13.8m

45 ft

X - Y Cross Section at 16 ft

Mounting Height

12m

39 ft

12m

39 ft

16 ft

(54°)

(51.3°) (51.3°)

(54°)

12m

39 ft

12m

39 ft

16 ft

46.3°

(49.5°)

46.3°

(49.5°)

MAGNUM FIRST M9-ML2 Installation guide

MAGNUM FIRST M9-ML2 Installation guide

MAGNUM FIRST M9-ML2 Installation guide

Related papers

Other documents