MillerEdge Rband Operating instructions

Brand: MillerEdge

Model: Rband

Type: Operating instructions

MillerEdge Rband is a wireless sensing edge system designed to enhance the safety and convenience of commercial door operators. It offers several key features and potential use cases:

Wireless Connectivity: The Rband system utilizes wireless technology to establish communication between the receiver and transmitter, eliminating the need for hardwired connections. This simplifies installation and provides greater flexibility in positioning the components.
Monitored and Non-Monitored Safety Edges: The system supports both monitored and non-monitored safety edges. Monitored safety edges provide an additional layer of protection by constantly checking for proper functionality, while non-monitored edges offer a cost-effective option for basic safety needs.

MillerEdge Rband is a wireless sensing edge system designed to enhance the safety and convenience of commercial door operators. It offers several key features and potential use cases:

Wireless Connectivity: The Rband system utilizes wireless technology to establish communication between the receiver and transmitter, eliminating the need for hardwired connections. This simplifies installation and provides greater flexibility in positioning the components.
Monitored and Non-Monitored Safety Edges: The system supports both monitored and non-monitored safety edges. Monitored safety edges provide an additional layer of protection by constantly checking for proper functionality, while non-monitored edges offer a cost-effective option for basic safety needs.

RBand Wireless Sensing Edge System Instructions

WARNING

BE SURE ELECTRICAL POWER HAS BEEN DISCONNECTED FROM THE INPUT POWER LINES PRIOR TO REMOVING THE

ELECTRICAL BOX COVER. AN APPROPRIATE LOCK-OUT/TAG-OUT PROCEDURE IS RECOMMENDED.

For Commercial Door Operators Using a T3/DC (red band) or T2 Edge (blue band)

CAUTION: THIS PROCEDURE MUST BE PERFORMED WITH THE DOOR IN THE CLOSED POSITION ONLY.

Door Installation - Wireless Edge System:

1. Move door to the fully closed position.

2. Remove power from the unit. Use proper lock-out/tag-out procedures. (Refer to OSHA Standard

1910.147).

NOTE: This instruction only applies to connecting the RBand Wireless Monitored Edge System to the operator, use

instruction included with sensing edge system to install the edge and program the wireless system. Use the chart

below to determine the appropriate wiring diagrams to use for the application.

Edge Type & Operation Operator Series

RB-P-K10

Receiver

Wiring

RB-TX10

Transmitter

Wiring

GT3C

Converter

Wiring

Door

Layout

T3 Monitored Safety Edge (red band) X and Y-Series Counter, Light,

Medium, Standard & Heavy-Duty Fig. 1 Fig. 4 Fig. 4 Fig. 6

T3 Monitored Safety Edge (red band) Light-Duty Jackshaft & Trolley Fig. 2 Fig. 4 Fig. 4 Fig. 6

T2 Monitored Safety Edge (blue band) X and Y-Series Counter, Light,

Medium, Standard & Heavy-Duty Fig. 1 Fig. 5 Not Used Fig. 8

T2 Monitored Safety Edge (blue band) Light-Duty Jackshaft & Trolley Fig. 2 Fig. 5 Not Used Fig. 8

T3 Non-Monitored Safety Edge

(red band)

X and Y-Series Counter, Light,

Medium, Standard & Heavy-Duty Fig. 3 Fig. 4 Fig. 4 Fig. 7

T2 Non-Monitored Safety Edge

(blue band)

X and Y-Series Counter, Light,

Medium, Standard & Heavy-Duty Fig. 3 Fig. 5 Not Used Fig. 9

3. Mount the RBand receiver near the operator powerhead in a dry area.

4. Route wire from RBand receiver to operator powerhead and attach as shown below.

5. Mount RBand RB-TX10 transmitter, GT3C converter (when required), transformer (when required) and

edge sensor as shown in the manufacturers instructions.

6. Wire safety edge, GT3C converter (when required) per application using table above.

7. Insert batteries into the RB-TX10 transmitter and GT3C converter (when required)

8. Apply power to operator.

9. Follow RBand instruction sheet to learn the RB-P-K10 receiver to the RB-TX10 transmitter.

10. Program operator ODC-STB to the ON status (see installation manual).

11. Run full operational and safety function test.

113179.01327, 09/2022

RBand Transmitter & Converter Wiring Installation for Wireless T3 Safety Edge

RBand Transmitter Wiring Installation for Wireless T2 Safety Edge

RBand GT3C

Converter

RBand RB-TX10

Transmitter

Safety

Edge

T3 Edge

Red Band

Fig. 4

RBand RB-TX10

Transmitter

Safety

Edge

T2 Edge

Blue Band

Fig. 5

RBand RB-TX10

Transmitter

Monitored

Photocells

Operator RB-P-K10

Receiver

RBand RB-TX10

Transmitter

RBand RB-TX10

Transmitter T3 Red

Band

OperatorRB-P-K10

Receiver

RBand RB-TX10

Transmitter

24V AC

Transformer

(when required)

T3 Safety Edge

T2 Safety Edge

T3 Safety Edge

Monitored

Photocells

T2 Safety Edge

NON-MONITORED Door InstallationMONITORED Door Installation

RBand GT3C

Converter

T2 Blue

Band

T2 Blue

Band

T3 Red

Band

RBand GT3C

Converter

Fig. 6 Fig. 7

Fig. 8 Fig. 9

Control Wire

Terminals

STB

BWC

MONITORED T3 or T2 Wireless Sensing Edge RBand Receiver Wiring Installation

X and Y-Series Commercial Operators

Light-Duty Commercial Trolley & Jackshaft

Fig. 2

X and Y-Series Commercial Operators

ON-MONITORED T3 or T2 Wireless Sensing Edge RBand Receiver Wiring Installation

Light-Duty Commercial Operator

(Jackshaft & Trolley)

White

RB-P-K10 Receiver

Control Wire

Terminals

ODC

STB External

Radio

Harness

Blue

Yellow

X & Z-Series Operators

(Counter Door, Medium, Standard & Heavy-Duty)

ODC

STB

Fig. 1

Orange

Blue

Yellow

12/24V

ac/dc

N/A

PE2

PE1

N/O

White

RB-P-K10 Receiver

Control Wire

Terminals

N-O

REV External

Radio

Harness

Blue

Yellow

X & Z-Series Operators

(Counter Door, Medium, Standard & Heavy-Duty)

N-O

REV

Fig. 3

Orange

Blue

Yellow

12/24V

ac/dc

White

RB-P-K10 Receiver

Blue

Yellow

12/24V

ac/dc

115 VAC

to 24 VAC

Transformer

P/N: 36238A

(Not Included)

N/A

PE2

PE1

N/O

COM

N/A

PE2

PE1

N/O

COM

MillerEdge Rband Operating instructions

Brand: MillerEdge

Model: Rband

Type: Operating instructions

MillerEdge Rband is a wireless sensing edge system designed to enhance the safety and convenience of commercial door operators. It offers several key features and potential use cases:

Wireless Connectivity: The Rband system utilizes wireless technology to establish communication between the receiver and transmitter, eliminating the need for hardwired connections. This simplifies installation and provides greater flexibility in positioning the components.
Monitored and Non-Monitored Safety Edges: The system supports both monitored and non-monitored safety edges. Monitored safety edges provide an additional layer of protection by constantly checking for proper functionality, while non-monitored edges offer a cost-effective option for basic safety needs.

Download PDF

report

MillerEdge Rband Operating instructions

MillerEdge Rband Operating instructions

Other documents