2. Crystorama
  3. EMO-5409-BF
EMO-5409-BF

Crystorama EMO-5409-BF User manual

  • Hi, I'm a chat assistant and I've reviewed the assembly instructions for the Crystorama EMO-5409-BF light fixture. This document provides detailed steps on how to assemble the fixture, including connecting light clusters, hanging rods, and banding rings. It also covers important safety precautions, proper wiring methods, and the use of independent support during installation. I'm ready to answer any questions you have about assembling or using this light.
  • How many candelabra base bulbs are needed for this fixture?
    What type of bulbs are recommended?
    Is this fixture suitable for damp locations?
ASSEMBLYINSTRUCTIONMODEL#EMO-5409-BF
CRYST
RAMA
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
WARNING:
ElectricalDanger TurnPoweroff
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
Youwillneed22-CandelabraBaseBulb
40WattsRecommended60WattsMax.
USELEDBULBSFOREXTENDEDUSE
This fixture is Damp rated
Howtoinstall
9.Installthebulbs(notincluded)intothesocket.
1.Slipthecenterstemalongwireandthreadontothe
nipplelocatedonthetopofthelightcluster#1.
2.Sliptheloopassemblyalongwireandthreadinto
thecenterstem.
6.Connectoneendofthehangingrodintotheholeof
thebandingring#1.Connecttheotherendofitonto
theloopassembly.
10.Hangglassdroptothebandingring.
(W1’’xL7-7/8’’)x322sets
CHAIN
HANGINGROD
QUICKLINK
LOOP
CENTER
STEM
LIGHT
CLUSTER#1
SETSCREW
TUBE
HOLES
LIGHT
CLUSTER
#2
SETSCREW
LIGHT
CLUSTER
#3
LIGHTCLUSTER#4
TUBE
TUBE
COUPLER
Performthewire
connectionsbyplugging
thewireconnectors
together.
WIRECONNECTOR
3.Sliponeofthetubesoverthecoupleronthebottom
ofthelightcluster#1andlineuptheholesonitwith
theholesonthecoupler.Secureitwiththescrew.
4.Connectthefixturewirefromlightcluster#1onto
thewirefromlightcluster#2bypluggingthewire
connectortogether.Raisethelightcluster#2upto
allowthecouplerontopofittoslipintothetube
andlineuptheholesonitwithholesonthetube.
Secureitwiththescrew.
5.Repeatstep3and4forassemblyofthelightcluster
#3andlightcluster#4.
7.Connectoneendoftheinnerhangingrodontothe
looponthebandingring#1.Connecttheotherend
ofitontotheloopsofthebandingring#2.
8.Repeatstep7forassemblyofthebandingring#3
andbandingring#4..
Refertothesafetycablemountingonthenextpage!
COUPLER
WIRE
CONNECTOR
BANDINGRING#3
GLASSDROP
(46PCS)
GLASSDROP
(68PCS)
BANDINGRING#4
GLASSDROP
(92PCS)
BANDINGRING#2
LOOP
INNER
HANGING
ROD
GLASSDROP
(116PCS)
BANDING
RING#1
LOOP
Crystorama.com
GROUND
WIRE
GROUND
WIRE
MAINWIRE
MAINWIRE
Groung
wire
Groung
wire
Main
wire
Main
wire
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
ASSEMBLYINSTRUCTIONMODEL#EMO-5409-BF
5’’
3/4’’
181-1/2’’
55-1/4’’
40’’
Crystorama.com
SAFETY CABLEINSTALLATIONINSTRUCTIONS
NIPPLE
HEXNUT
WASHER
HEXNUT
SAFETY CABLE
HOUSESUPPLY WIRES
HICKEY
FIXTUREWIRE
OUTLETBOX
HEXNUT NIPPLE
CANOPY
STRUCTURAL MEMBER
CLAMP
SETSCREW
SAFETY CABLE
COLLARRING
COLLARLOOP
IMPORTANT:
FOR A SAFE ANDSECUREINSTALLATION,THESEFIXTURESMUSTBEINSTALLEDBY
MEANSOFSUPPORTSTHAT AREINDEPENDENTOFTHEOUTLETBOX.
SUGGESTEDINSTALLATION:
1.Providea1/4IPSpipewithoneendsecurelymountedtoabeamorastructuralmember.
Theotherendshouldprotrudethroughthecenteroftheoutlet,asshown.
2. Assemblethescrewcollarloop,nipple,hexnutsandhickeytocenter1/4IPSsupport
pipeandadjustoveralllengthtoallowthecollarringtoholdthe canopyflushtothe
ceiling.Whentheadjustmentshavebeencompletedsecurethehexnut,asshown.
3.Useonequicklinktoconnectfixtureloopandthebottomofchain.Slidethescrewcollar
ringovertheupperendofthechain,throughthe(Finishedsidedown).Thenuseanother
quicklinktoconnectcollarloopandthetopofchain.
4.Lacethefixturewires,groundwiresandsafetycablethroughthechainandscrewcollar
loop,exitingthroughthesideofHICKEY.Proceedtoattach theFIXTUREGROUNDWIRE
toHOUSEGROUNDWIREusingwireconnector.Usingwireconnectors,connectthe
HOUSEWHITEWIREtotheFIXTURESUPPLY WIRE (WHITEORRIBBEDSIDE);connect
theHOUSEBLACK(orRED)WIREtotheFIXTURESUPPLY WIRE(BLACKorSMOOTH
SIDE).Wrapallconnectorswithapprovedelectricaltape.Wrapsafetycablearoundoutlet
boxbraceandpullcabletaut.Securecablewiththeclampand(2)setscrewsprovided,as
shown.
5.PushtheCANOPY upwardovertheOUTLETBOX.Besurethatallwiresarecarefully
tuckedintotheOUTLETBOXcavity.SecurecanopyagainstceilingbythreadingCANOPY
LOCKRINGontotheCANOPY LOOP.Tightenuntilsnug.
CHAIN
QUICKLINK
QUICKLINK
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
ASSEMBLYINSTRUCTIONMODEL#EMO-5409-BF
Hickey
Setscrew
Safetycable
Nipple
Structuralmember
Clamp
A
BC
D
E
Hexnut
Nipple
E
PartNumber
PartNumbers
J.(1)-Bandingring#1#W40’’xH1-5/8’’ #XRF5409BFRING1
K.(3)-TubeW1’’xL6-7/8’’
A.(1)-CanopyW5’’xH3/4’’ #XRF5409BFCAN5IN
B.(1)-Collarring
C.(1)-Collarloop
D.(1)-Chain-L120’’,5mmthick#XRF5409BFCHA5MM
F.(1)-Loopassembly#XRF5409BFLOOP
H.(3)-Hangingrod#W1-1/8’’xL25-1/8’’ #XRF5409BFROD25IN
E.(2)-Quicklink
L.(322)-Glassdrop
F
G
H
I
J
K
L
M
N
O
P
G.(1)-Centerstem#W5/8’’xL16-1/2’’ #XRF5409BFSTEM16.5IN
I.(18)-Setscrew
M.(9)-Innerhangingrod#XRF5409BFINROD9IN
N.(1)-Bandingring#2#W32’’xH1-5/8’’ #XRF5409BFRING2
O.(1)-Bandingring#3#W24’’xH1-5/8’’ #XRF5409BFRING3
P.(1)-Bandingring#4#W16’’xH1-5/8’’ #XRF5409BFRING4
Crystorama.com
/