SIRETTA SNYPER-LTE User guide

Brand: SIRETTA

Model: SNYPER-LTE

Type: User guide

This manual is also suitable for

SNYPER-LTE+ Graphyte Network Signal Analyzer

SIRETTA SNYPER-LTE is a powerful cellular signal analyzer designed for professional use. With its advanced capabilities, it allows users to analyze and troubleshoot cellular networks, identify signal issues, and optimize network performance. The device features a user-friendly interface, comprehensive measurement functions, and the ability to generate detailed reports. Whether you're a network engineer, installer, or technician, the SIRETTA SNYPER-LTE provides the tools you need to ensure reliable and efficient cellular connectivity.

Firmware Update Procedure

What You’ll Need

Figure 2. USB mini to USB Cable Figure 3. Local PC

Figure 1. SNYPER Signal Analyser

»SNYPER Signal Analyser

»Siretta Approved USB Mini to USB Cable

»PC / Laptop

SNYPER Layout

Registered in England No. 08405712

VAT Registration No. GB163 04 0349

Siretta Ltd

Basingstoke Road

Spencers Wood

Reading

Berkshire RG7 1PW

sales

fax

web

+44(0)118 976 9000

+44(0)118 976 9020

[email protected]

www.siretta.com

SNYPER-LTE Graphyte

User Manual

Product Images

Figure 1. Front view of the SNYPER-LTE Graphyte

320 x 240

LCD Display

(51 x 38mm viewing area)

RIGHT Button

BACK Button

DOWN Button

OK Button

LEFT Button

Charge Status

LED

ON/OFF Button

UP Button

First Step...

Figure 4. SNYPER Functions

Prepare your SNYPER as follows:

Next Step...

»Ensure the latest SNYPER software is installed on the device.

»This process will work on software version 06.10.xx onwards.

***IMPORTANT***

»Double check the rmware is correct for your V1 device before attempting to update the rmware.

***IMPORTANT***

»The silver label on the back of the SNYPER will clearly identify the model.

»Always use a high quality, short USB cable to connect the device to a PC (Use the Siretta approved USB cable)

»You must connect the USB cable directly from the device to the PC and not go through a USB hub.

***IMPORTANT***

»Some antivirus applications have been known to interfere with the software update procedure.

Please disable if you have difculties.

»We have tested our rmware update procedure using Bitdefender and this works as expected.

Please follow the preparation steps below to ensure you are using the correct rmware for

your device and avoid the common mistakes made when updating device rmware.

The procedure steps in this document ensure that you can reliably update your SNYPER

without running into difculties and should prevent rmware update failures.

V1 Hardware Firmware Update

Preparation to begin Firmware Update:

1) Navigate to https://www.siretta.com/software-library/

2) Select ‘SNYPER Firmware Update’ tab

3) Download and install ‘USB Device Drivers’ from the Siretta Software Library to your PC

4) Download and install ‘XFP Programming Tool’ from the Siretta Software Library to your PC

Figure 5. Downloading support tools

Select ‘SNYPER Firmware Update’

Install ‘XFP Progamming Tool’

Next Step...

NOTE: Devices which do not have V2 marking in the model name are V1 hardware.

Preparing for Firmware Update

Install ‘USB Device Drivers’

Download Firmware

Download the latest rmware for the SNYPER from the Siretta Website:

1) Download the correct rmware for your device

(Refer to the silver label on the back of your SNYPER to identify the correct model)

Figure 6. Downloading SNYPER rmware

Next Step...

Preparing the XFP Tool

Preparing the XFP tool to update SNYPER rmware:

1) Unzip the rmware and store the uncompressed le locally on your PC

2) Run XFP and ensure that the ‘Port’ is set to ‘USB’ and ‘Speed’ is set to ‘460800’

3) Within XFP click ‘Browse’ to navigate to the rmware binary on your PC

4) Connect the SNYPER directly to your PC using the approved USB cable

5) Power off the SNYPER

Figure 7. Preparing XFP tool

Set ‘Port’ and ‘Speed’

Select rmware for update

Begin update procedure

Preparing SNYPER for Firmware Update

Figure 8. Power on SNYPER

At this point it is now possible to update the SNYPER rmware:

1) Click ‘Program’ on the XFP tool

2) Press and hold the ‘Back’ button and press the ‘Power’ button momentarily to power on

the SNYPER

3) The SNYPER will enter the special rmware programming mode

4) The SNYPER screen will show ‘Starting Modem’ whilst the modem is being initialised

5) Once the module is connected and powered up the SNYPER screen will show ‘Modem On’

Press and hold back button

Momentarily press power button

Figure 9. Firmware update mode

Next Step...

Firmware Update in Progress

The rmware update procedure will now begin:

1) The XFP application will display ‘Linking’ and then ‘Programming’ in the bottom left corner

2) The progress bar will indicate the update process and how much is remaining

3) Once the rmware update has completed you will be presented with a complete popup box

4) Press and hold the power button to power off the SNYPER and exit programming mode

5) Power on the SNYPER for the unit to re initialise

6) You can now perform surveys as normal

Complete!

Figure 10. Programming in progress

Progress/status bar

Figure 11. Programming complete

V2 Hardware Firmware Update

Preparation to begin Firmware Update:

1) Navigate to https://www.siretta.com/software-library/

2) Select ‘SNYPER Firmware Update (V2)’ tab

3) Download and install ‘USB Device Drivers’ from the Siretta Software Library to your PC

Figure 5. Downloading support tools

Select ‘SNYPER Firmware Update (V2)’

Next Step...

NOTE: Devices which have V2 marking in the model name are V2 hardware.

Preparing for Firmware Update

Install ‘USB Device Drivers’

Download Firmware

Download the latest rmware for the SNYPER from the Siretta Website:

1) Download the correct rmware for your device

(Refer to the silver label on the back of your SNYPER to identify the correct model)

2) Copy the rmware le you have download into a folder on your PC

Figure 6. Downloading SNYPER rmware

Next Step...

Preparing SNYPER for Firmware Update

Figure 8. Power on SNYPER

Follow the steps below to prepare your SNYPER for a rmware update:

1) Connect the SNYPER directly to your PC using the approved USB cable

2) Power off the SNYPER

3) Press and hold the ‘Back’ button and press the ‘Power’ button momentarily to power on the SNYPER

4) The SNYPER screen will show ‘Starting Modem‘ whilst the modem is being initialised

5) Once the module is connected and powered up the SNYPER screen will show ‘Modem On’

6) Check that ‘Telit Serial Diagnostics Interface’ appears in device manager as shown below in gure 10

Press and hold back button

Momentarily press power button

Figure 9. Firmware update mode

Next Step...

Figure 10. Device manager

‘Telit Serial Diagnostics

Interface’ shown here

Run Firmware Update

At this point it is now possible to begin the rmware update:

1) Run the le you have downloaded to start the rmware update

2) It should take around 5 minutes to complete the rmware update

3) Once complete, the programming window will show ‘Completed Successfully’

4) Close the programming window once complete

5) Press and hold the power button to power off the SNYPER and exit programming mode

6) Power on the SNYPER for the unit to re initialise

7) You can now perform surveys as normal

Complete!

Figure 10. Firmware update in progress

Setting the new standard in cellular signal analysers

+44 (0)118 976 9000

www.siretta.com

Siretta Ltd, Basingstoke Road, Spencers Wood, Reading, Berkshire, RG7 1PW, UK Rev 1.0

SIRETTA SNYPER-LTE User guide

Brand: SIRETTA

Model: SNYPER-LTE

Type: User guide

This manual is also suitable for

SNYPER-LTE+ Graphyte Network Signal Analyzer

Download PDF

report

SIRETTA SNYPER-LTE User guide

This manual is also suitable for

SIRETTA SNYPER-LTE User guide

Related papers

Other documents