INSTALLATION & MAINTENANCE MANUAL
SPKEVF / SPKEVTxx
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
SPKEVF / SPKEVTxx
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
• If used under insulation, the insulation should be laid unbroken over the luminaire (not packed around it).
Only mineral wool style insulation may be used
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP65 rated (IP20 from above)
SAFETY
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to infringe
with any joists, gas/water pipes, or electrical cables
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
SPEKFCWA / SPEKTCWA
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
• If used under insulation, the insulation should be laid unbroken over the luminaire (not packed around
it). Only mineral wool style insulation may be used
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP65 rated (IP20 from above) for the SPEKFCWA and IP20 for the SPEKTCWA
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes, or electrical cables
Fig. 1
• Open the terminal cover by squeezing the two lugs and push up (see Fig. 2)
Fig. 2
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
SPEKFCWA / SPEKTCWA
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
• If used under insulation, the insulation should be laid unbroken over the luminaire (not packed around
it). Only mineral wool style insulation may be used
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP65 rated (IP20 from above) for the SPEKFCWA and IP20 for the SPEKTCWA
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes, or electrical cables
Fig. 1
• Open the terminal cover by squeezing the two lugs and push up (see Fig. 2)
Fig. 2
Fig. 1
Fig. 2
• Open the terminal cover by squeezing the two lugs and push up (see Fig. 2)
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3):
L - Live (Brown), E - Earth (Green/Yellow), N - Neutral (Blue). The earth terminal is non-functional and only
provided for convenience
70mm
Fig. 3
Fig. 4
• Close the terminal cover
• Select the required wattage and colour temperature: on the SPKEVF the switches are accessed beneath the
magnetic bezel; on the SPKEVTxx the switches are on the rear of the luminaire (see Fig. 4)
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3):
L - Live (Brown), E - Earth (Green/Yellow), N - Neutral (Blue). The earth terminal is non-functional and
only provided for convenience
Fig. 3
• Close the terminal cover
• Select the desired wattage and colour temperature via the switches on the back of the downlight
(see Fig. 4)
Fig. 4
Note – Please note that this product is supplied without a bezel. Bezels must be purchased separately and
must be used to ensure the IP rating of the product
• Add a bezel to the downlight. For the fixed version, align the two lugs on the bezel with the clasps on
the downlight and rotate clockwise. For the tilted version, insert the inner bezel and align the clips of
the outer bezel with the indents on the downlight and rotate anti-clockwise (see Fig.5)
Fixed version Tilted version
Fig. 5
• Close the terminal cover
• Select the required wattage and colour temperature: on the SPKEVF the switches are accessed
beneath the magnetic bezel; on the SPKEVTxx the switches are on the rear of the luminaire (see Fig.
4)
Fig. 4
SPKEVF SPKEVTxx
• SPKEVF: add a bezel to the downlight (bezels are sold separately) – align the bezel with the downlight
and it will attach magnetically
• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 5)
Fig. 5
• Switch on and check for correct operation
Fig. 5
• SPKEVF: add a bezel to the downlight (bezels are sold separately) – align the bezel with the downlight and it
will attach magnetically
• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 5)
• Switch on and check for correct operation
• Close the terminal cover
• Select the required wattage and colour temperature: on the SPKEVF the switches are accessed
beneath the magnetic bezel; on the SPKEVTxx the switches are on the rear of the luminaire (see Fig.
4)
Fig. 4 SPKEVF SPKEVTxx
• SPKEVF: add a bezel to the downlight (bezels are sold separately) – align the bezel with the downlight
and it will attach magnetically
• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 5)
Fig. 5
• Switch on and check for correct operation
GENERAL
This product contains a light source of energy efficiency class C to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable LED light source and a non-replaceable control gear.
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
Symmetrical and asymmetrical lenses, FLHLAS100 / FLHLAS200 / FLHLSM100 / FLHLSM200
• Remove the diffuser by unscrewing the 4 corner screws
• Remove the LED array screws
• Add the lens ensuring the arrow printed in the top middle of the lens is pointing upwards
• Fix the lens with the LED array screws
• Reattach the diffuser
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
GENERAL
This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable light source and a non-replaceable control gear
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents that may damage the product.
This product is non-dimmable.
The external supply cable of this luminaire cannot be replaced; if the cable is damaged, the luminaire should be
destroyed.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 5 years from the date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
230V 50Hz, IP66, Class I, Non-Dim, Ta: -30~+40, cracked glass
AVMAR22_V1
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable with leading or trailing edge dimmers, please check compatibility before installation.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
The external supply cable of this luminaire cannot be replaced; if the cable is damaged, the luminaire should be
destroyed
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
DCJUL23_V1
55
SUPPLIED BY:
(UK) MANUFACTURER
ML ACCESSORIES LTD, UNIT E CHILTERN PARK,
BOSCOMBE ROAD, DUNSTABLE LU5 4LT,
WWW.MLACCESSORIES.CO.UK
(EU) AUTHORISED REPRESENTATIVE
SLV LIGHTING GROUP,
DAIMLERSTRASSE 21-23,
52531 ÜBACH-PALENBERG, GERMANY
EMAIL: EPREL@GROUP.SLV.COM
MADE IN CHINA
230V
50Hz 60° >80
CRI 25°C
TA ACOUSTIC
RATED
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
ML Accessories SPKEVTW User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories SPEKTCWA User manual
-
-
Knightsbridge EMPOWERST User manual
-
-
-
-
-
-
-