Kmart 43138944 User manual

Kmart
Brand
Kmart
Model
43138944
Category
Flat panel desk mounts
Type
User manual
Installation Manual
4-in-1
Desk
Streaming
Stand
43138944
Attach Mount to Work Surface
Attach Arm to the Post
Installation Hardware
X 1
Base Stem
X 1
Arm (α)
X 2
Arm (β)
X 1
Tablet Holder
X 1
Adaptor
X 1
Ring Fill Light
X 2
Universal Ball Head
X 2
Clip
X 1
Phone Holder
X 1
Post Cap
4/5/6mm X 1
Hex Wrench
X 1
VESA Connector
X 6
Screws(M4)
X 6
Screws(M5)
X 1
Extension Rod
Accessory
X 1
Laptop Plate
X 1
Microphone
Main Stand
X 1
Microphone Holder
For installation on open edge of work
surface:
Slide the base stem A against work
surface edge and fully tighten
clamp Screw B.
Clip
Arm(α)
Arm(β)
Arm(β)
Post Cap
Parallel Connector
Screw(A)
As the picture shows
put the Clip Arm(α)
Clip Arm(β)
Parallel Connector into the Pole
cover then Post Cap, then,
tighten the screw.
INSTALLING MICROPHONE HOLDER:
Place the microphone main stand at the inside hole of the
parallel connector, tighten the screw which is at the back of
the parallel connector.
INSTALLING MOBILE PHONE HOLDER:
INSTALLING TABLET HOLDER:
Install the universal ball head
at the arm(β) first, then install
the phone holder.
If you want to get taller
height, you could install the
extension rod between the
universal ball head and the
phone holder.
Remove the screws from the
holder adapter by the hex
wrench.
As the picture shows, use
the hex wrench to remove
screws on arm (β).
As the picture shows, put
the accessories at the
separated arm, put the
screw back then tighten it.
VESA :
75*75mm 100*100mm
As the picture shows, install
VESA mount on monitor. Be
careful to leave the slide
clip upwards
Insert the VESA connector
into the groove, when you
hear a click sound it means
done.
INSTALLING MONITOR:
Install the universal ball
head at the arm(β) at first,
then install the ring fill light.
If you want to get taller height,
you could install the extension
rod between the universal ball
head and the ring fill light.
INSTALLING RING FILL LIGHT:
Remove the screws from the
adapter by the hex wrench.
As the picture shows, put
the accessories at the
arm(α), tighten the screw.
Insert the Laptop Plate into
the groove, when you hear
a click sound it means done.
Note: If you would like to
lower the height, please
detach the arm bracket
first(A), then insert arm as
pictured.
ADAPTER INSTALLATION
INSTALLING LAPTOP PLATE:
Warning
Product Specification
Cable Management
Arm Adjustments
Please read this manual carefully and make sure you fully
understand it before installation. If there is any confusion,
please visit our website or contact our service team.
Please use attached tools or relevant support tools during
installation.
If you feel the pitching angle is too tight or too loose
when adjusting the mount, please adjust the screws.
Slide the plastic cover on the lower link upwards until it
disengages, then remove (A). Put power and monitor cables
into the plastic cover (B). Then slide the cover downwards
until it clicks into place (C).
Remove cable clip (A) from
the arm, thread cables, install
cable clip on the arm again.
Note: Open cable clip two sides.
Screws(M4) or Screws(M5)
Slide
Maximum load for single arm: 8KG
Monitor mounting: VESA 75x75mm & 100x100mm
Ring light:
DC5V/2A, 10” 120 beads
500 lux cool white/warm white/natural white
3200~5600K
Holders compatible:
12~17” laptop
4~12.9” tablet
4~6” mobile phone
To ensure safety, maximum load
for every arm is not to exceed 8KG
Compatible with phone size 4”~6”
Compatible with tablet size 4”~12.9”
Compatible with laptop
size 12”~17”
Clip A Clip A
43138944
43138944_4-in-1 Desk Streaming Stand-IM-V
Artwork Proof Date: 02.14.2022
297mm
105mm
297mm
105mm
  • Page 1 1

Kmart 43138944 User manual

Kmart
Brand
Kmart
Model
43138944
Category
Flat panel desk mounts
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents