Aqua-Hot AHE-400-P01 Installation guide

400LP

INSTALLATION MANUAL

AVERTISSEMENT. Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire

au minimum le risque d’incendie ou d’explosion ou

pour éviter tout dommage matériel, toute blessure ou

la mort.

— Ne pas entreposer ni utiliser d’essence ou ni d’au-

tres vapeurs ou liquides inflammables à proximité

de cet appareil ou de tout autre appareil.

— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Évacuez le véhicule.

• Coupez l’alimentation en gaz au réservoir ou à la

source.

• Ne touchez à aucun interrupteur ; ne pas vous

servir du téléphone ou de la radio du véhicule.

• Ne pas démarrer le moteur du véhicule ni aucune

génératrice électrique.

• Appelez le fournisseur de gaz le plus proche ou

un

technicien qualifié.

• Si vous ne pouvez rejoindre ni un fournisseur ni

un

technicien qualifié, appelez le service des

incendies le plus proche.

• Ne pas rétablir l’alimentation en gaz tant que la

fuite n’a pas été réparée.

— L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié ou

par le fournisseur de gaz.

WARNING: If the information in these instructions is

not followed exactly, a fire or explosion may result

causing property damage, personal injury, or death.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any oth-

er appliance.

— WHAT TO DO IF YOU SMELL GAS

• Evacuate all persons from the vehicle.

• Shut off the gas supply at the gas container or

source.

• Do not touch any electrical switch or use any

phone or radio in the vehicle.

• Do not start the vehicle’s engine or electric

generator.

• Contact the nearest gas supplier or qualified

service technician for repairs.

• If you cannot reach a gas supplier or qualified

service technician, contact the nearest fire

department.

• Do not turn on the gas supply until the gas leak(s)

has been repaired.

— Installation and service must be performed by a

qualified installer, service agency, or the gas sup-

plier.

CAUTION:

The Aqua-Hot tank and heating loop operate at

0.0 psi (zero pressure system). Air pressure

applied to the tank MUST NOT exceed 20 psi.

Excess pressure will result in internal damage.

CAUTION:

Before welding or plasma cutting on any coach;

it is necessary to disconnect the electric wiring to

the Aqua-Hot System.

Failure to disconnect the wires from the

Aqua-Hot System before using a welder or a

plasma cutter on the coach may cause damage to

the Aqua-Hot.

TABLE OF CONTENTS

Aqua-Hot 400-LP Installation Manual

Introduction ........................................................................................................................................... 5

Section 1: Aqua-Hot Hydronic Heating System

Technical Information .......................................................................................................................... 6

ID Label ................................................................................................................................................. 7

Overview ................................................................................................................................................ 8-9

Section 2: Aqua-Hot Installation

Installing the Mounting Tray and the Aqua-Hot ............................................................................. 10

Overall Aqua-Hot Dimensions ........................................................................................................... 11-12

Installing the Expansion Tank ............................................................................................................ 14

Section 3: Hydronic Heating System

Heat Exchanger Location and Clearances ........................................................................................ 15

Heat Exchanger Mounting Requirements ......................................................................................... 15

Sample Heating System Floorplan ..................................................................................................... 16

Mounting the Heat Exchangers .......................................................................................................... 17

Wiring the Heat Exchangers ............................................................................................................... 19

Plumbing Requirements ....................................................................................................................... 21

Plumbing the Hydronic Heating System ........................................................................................... 22

Section 4: Thermostats

Fresh Water Tank Thermostat ............................................................................................................ 25

Room Thermostats ............................................................................................................................... 26

Section 5: Domestic Water System

Domestic Water System Requirements ............................................................................................. 27

Domestic Water System Plumbing ..................................................................................................... 27

Section 6: Switch Panel

Switch Panel Location .......................................................................................................................... 29

Switch Panel Mounting ........................................................................................................................ 29

Switch Panel Wiring .............................................................................................................................. 30

Section 7: Fuel System

Fuel System Requirements ................................................................................................................... 31

Fuel System Installation ....................................................................................................................... 31

Section 8: Exhaust System

Exhaust System Requirements ............................................................................................................ 33

Installing the Exhaust System.............................................................................................................. 33

Section 9: Electronic Controller Wiring

Electronic Controller Wiring……………………………………………………………...39

Wiring Harness Connection………………………………………………………………40

Connecting the 12 Volt-DC Power……………………………………………………….41

Section 10 Purging the Systems

Purging the Hydronic Heating System ............................................................................................... 42

Purging the System by Grounding the Zone Thermostat Connection ......................................... 43

Purging the Domestic Water System .................................................................................................. 43

Purging the Propane Fuel System ....................................................................................................... 45

Section 11: Initial Start-Up

Activating the Aqua-Hot ...................................................................................................................... 47

Appendices:

Appendix A: Wiring Diagram.............................................................................................................. 48

Appendix B: Wire Gauge Information .............................................................................................. 49

Appendix C: Electronic Controller Features..................................................................................... 50

Appendix D: Antifreeze Types ........................................................................................................... 52

Appendix E: Antifreeze Mixture Water Quality Recommendations ............................................. 52

Appendix F: Antifreeze Terms and Mixture Ratio .......................................................................... 53

Appendix G: Measuring Propylene Glycol Levels Using a Refractometer .................................. 55

TABLE OF CONTENTS (CONTINUED)

INTRODUCTION

Danger, Warning, Caution, and Note Boxes:

Danger, Warning, Caution, and Note boxes appear throughout

this manual as a means of alerting the installer to important

information.

INDICATES THAT PERSONAL INJURY IS LIKELY OR IMMI-

NENT.

Indicates that serious damage to the heater will occur and

personal injury is possible as well.

Indicates that damage to the heater is possible.

NOTE: Indicates information that requires special attention by

the installer.

— Page 5 —

CAUTION:

! DANGER !

WARNING

The Aqua-Hot 400LP is a hydronic (water based)

heating system, and a tank-less hot water system.

The heating system provides moist, quiet, comforta-

ble, interior heat with up to five separate, thermo-

statically-controlled temperature zones, and prevents

tank and line freezing in the bays.

The tank-less hot water system produces 75 gallons

per hour of continuous, on-demand, hot water.

This TribridHot™ designated system uses one or a

combination of heat sources to heat FDA-approved

Generally Recognized as Safe (GRAS) propylene

glycol based boiler antifreeze solution in the Aqua-

Hot’s boiler tank.

The 400LP uses one 120 Volt-AC, 1650 Watt elec-

tric element to heat the system when shore power is

available, and a 12 Volt-DC powered propane burn-

er provides heat when dry camping. The heat

sources can be used separately or together.

This Installation Manual is designed to aid in the

installation process of the Aqua-Hot 400LP Hydron-

ic Heating System by a trained and experienced

technician.

Please note that all Danger, Warning, Caution, and

Note boxes, appearing as needed throughout this

manual, must be reviewed and adhered to during the

installation procedure in order to avoid potential

hazards, which could result in injury, death, product

damage, or property damage.

Should additional assistance be needed, please con-

tact the Product Application Department at 1-800-

685-4298, Monday through Friday, between the

hours of 7:00 AM and 4:00 PM Mountain Time.

SECTION 1: AQUA-HOT HYDRONIC HEATING SYSTEM

Propane Burner, Heat Input (Firing Rate) ................................................................................................................................ 55,331 BTU/hr

Propane Burner, Fuel Consumption (Continuous Operation) ............................................................................. 0.72 gal/hr, 2.72 liters/hr

Heater, Voltage/Maximum Power Consumption......................................................................................................... 12 Volt-DC/60 watts

Electric Heating Element specifications .................................................................................................................... 120 Volt-AC/1650 watts

Zone Heat Circulation Pump specifications .................................................................................................... (2) 12 Volt-DC/21 watts each

Number of Heating Zones ............................................................................................................................................................. Maximum of 5

Domestic Water Heating Capacity ............................................................................................................................ Continuous/On-Demand

Dimensions ..................................................................................................................................................................... 12”H x 18.5”W x 29.5”L

Dry Weight .......................................................................................................................................................................... approximately 127 lbs.

Wet Weight ......................................................................................................................................................................... approximately 184 lbs.

NOTE: All vehicle installations must comply with the requirements listed in the Recreational Vehicle Industry Associ-

ation’s (RVIA) ANSI/NFPA 1192 Handbook for Recreational Vehicle Standards. To receive a copy of this handbook

and other pertinent RVIA Standards, write to: Recreation Vehicle Industry Association, 1896 Preston White Drive,

P.O. Box 2999, Reston, VA 22090-0999, call them at (703) 620-6003, or visit them online at www.rvia.org.

Figure 1

— Page 6 —

SECTION 1: AQUA-HOT HYDRONIC HEATING SYSTEM

Each Aqua-Hot heating system possesses an I.D. label on the

unit itself. This I.D. label details the specifications of the

heater, to what standard it has been tested, and important

safety notices.

Figure 2

— Page 7 —

55,331 BTU/HR 16.2kWh

Figure 3

Propane Inlet

Ball Valve

Drain Valve

VAC Access

Panel

AC Terminal

Port

Propane

Burner

Heating Zone 1

Outlet Port

Heating Zone 2

Outlet Port

Zone 1

Circulation

Pump

Zone 2

Circulation

Pump

Propane

Burner

Controls

Figure 4

Domestic Hot

Water Outlet

Domestic Cold

Water Inlet

SECTION 1: AQUA-HOT HYDRONIC HEATING SYSTEM

— Page 8 —

Wiring Harness and

Harness Port

AC Terminal

Block

SECTION 1: AQUA-HOT HYDRONIC HEATING SYSTEM

— Page 9 —

Figure 5

AC Wiring Port

Zone 1 and 2

Outlet Ports

Fuel

Inlet Port

Zone 1 and 2

Inlet Ports

Air Release

Valve

Expansion Tank

Connection

Wiring Harness Port

WARNING!

The Aqua-Hot tank and heating loop

operate at 0.0 psi (zero pressure system).

Air pressure applied to the tank MUST

NOT exceed 20 psi. Excess pressure will

result in internal damage.

4. Insert a #10 machine screw into each of the embossed

holes in the mounting tray (total of six required) and tight-

en to secure the mounting tray to the motor home.

NOTE: Secure the mounting tray into place prior to install-

ing the Aqua-Hot.

Remove the access cover fastener from the Aqua-

Hot prior to installation of the Aqua-Hot into the

mounting tray.

Mount the Aqua-Hot securely into the mounting

tray to ensure that the unit does not move or

shift under normal operating conditions

5. Place the Aqua-Hot into the mounting tray. Reference

Figure 9.

NOTE: Remove the bolt securing the front of the access cover

to the mounting tray; this bolt will need to be re-

installed once the total installation procedure is com-

plete. Remove the access cover.

SECTION 2: AQUA-HOT INSTALLATION

Installing the Mounting Tray and the Aqua-Hot:

The Aqua-Hot must be installed in a compartment that is

completely closed-off from living quarters and accessible

only from the outdoors.

1. Reference the following illustrations for mounting infor-

mation:

• Overall Aqua-Hot dimensions - Figure 7

• Mounting tray information - Figure 8

• I.D. Label noting the “Open Access”

clearance requirement for the front of the heater

Figure 2

• Service access clearances - Figure 6

NOTE: Be sure to complete the following when installing the

Aqua-Hot:

Inspect the area beneath the mounting location to

ensure that no structural members will interfere with

the cut-out for the mounting tray.

Verify that an adequate support system has been

provided for the Aqua-Hot.

2. Cut out the required mounting tray opening. Reference

Figure 8.

3. Install the mounting tray flange into the cut-out opening.

Reference Figure 8.

. Figure 6

— Page 10 —

1/2 in

SECTION 2: AQUA-HOT INSTALLATION

— Page 11 —

Figure 7

15.27”

SECTION 2: AQUA-HOT INSTALLATION

Figure 8

— Page 12 —

SECTION 2: AQUA-HOT INSTALLATION

Figure 9

— Page 13 —

1/2 in.

Aqua Hot 400-LP

NOTE: Avoid any dips and bends in the overflow tubing from

the Aqua-Hot to the expansion tank as air can become

trapped in these dips and bends, preventing the expan-

sion of the heating solution from properly depositing

in the expansion tank.

SECTION 2: AQUA-HOT INSTALLATION

Figure 10

— Page 14 —

Expansion Tank

Connection

Installing the Expansion Tank:

Select a mounting location that allows for easy access

and clear visibility whenever the particular storage

bay door is open.

NOTE: The top of the expansion tank should always be

mounted at least 4 inches higher than the highest point

on the Aqua-Hot. Reference Figure 10.

1. Mount the expansion tank as illustrated in Figure 10.

2. Connect and clamp the overflow tubing from the ex-

pansion tank to the Aqua-Hot’s expansion tank con-

nection. Reference Figure 10.

3. Drill a hole in the bay floor and connect (secure with a

clamp) a long enough piece of overflow tubing so that

it can be connected to the top of the expansion tank

and extend through the bay floor.

CAUTION:

The Aqua-Hot tank and heating loop operate at

0.0 psi (zero pressure system). Air pressure ap-

plied to the tank MUST NOT exceed 20 psi. Ex-

cess pressure will result in internal damage.

Pressure Testing the Aqua-Hot Tank

400LP

SECTION 3: HYDRONIC HEATING SYSTEM

Heat Exchanger Locations and Clearances:

• Place the heat exchangers so that even heat distribu-

tion will be felt throughout the interior of the motor

home. Reference Figure 15A.

NOTE: For single slide-out configurations, it is usually sim-

plest to place a heat exchanger on the opposite side of

the motor home pointing towards the slide-out.

• Place the heat exchangers where they will be accessi-

ble for potential servicing and cleaning.

• Centralize and position a heat exchanger in the fresh

water storage tank plumbing bay. Reference Figure

11.

NOTE: In order to achieve the best heating results, place the

heat exchanger as close to the floor of the plumbing

bay as possible (heat will naturally rise).

• Reference Figures 12, 13, 14, and 15, for mounting

location information.

• Reference Figure 12 for clearance information.

NOTE: An accessory device is available for the Cozy Heat

Exchanger for the purpose of redirecting the airflow

from the heat exchanger. Reference Figures 16 and

17.

Mounting Requirements:

• Sufficient ventilation (return-air) must be supplied to

each interior heat exchanger. Reference Figure 15.

NOTE: Ventilation (return air) must be supplied from the liv-

ing area. Ventilation (return air) MAY NOT be sup-

plied from the bay area.

NOTE: Mounting the heat exchangers without sufficient ven-

tilation will severely reduce their overall heating per-

formance (heat output).

In order to provide sufficient ventilation, the return-air

registers must be the same size, or larger, than the

outlet-air registers.

Return-air must be supplied from the corresponding

interior heating zones.

Figure 11

Figure 12

— Page 15 —

Figure 13

Figure 14

Indicates sample mounting locations for the Cozy heat exchangers. Actual placement and quantity

vary based on the individual design of the coach. For specific design assistance, contact Aqua-Hot

at 303-659-8221

— Page 16 —

SECTION 3: HYDRONIC HEATING SYSTEM

Mounting the Heat Exchangers:

1. Cut out a 2.5 inch H x 10 inch W opening for each heat

exchanger outlet and cold-air return register. Reference

Figure 19.

2. Mount each heat exchanger permanently into place.

Reference Figures 18 and 19.

3. Install the hot-air outlet and cold-air return registers.

Reference Figure 15.

NOTE: Please note that a return-air register may not be re-

quired; however, adequate return-air must be pro-

vided to each particular heat exchanger. This means

that the total cross-sectional area of the return-air

opening must be equal to or greater than the cross-

sectional area of the hot-air outlet opening of the

heat exchanger.

If the toe-kick areas in the motor home are inadequate to

house a heat exchanger for regular installation, a plenum

may be used on the heat exchanger, which can be used with a

smaller vent as seen in Figure 17. The plenum allows only

the desired outlets to be opened by removing the metal insert

on the vent.

Figure 15

Figure 16

Figure 17

— Page 17 —

Vent installed

In toe-kick area

Cozy Heat

Exchanger

Hose to direct

air to vent

Toe Kick

Board

Plenum

SECTION 3: HYDRONIC HEATING SYSTEM

Figure 19

— Page 18 —

Figure 18

SECTION 3: HYDRONIC HEATING SYSTEM

Figure 20

— Page 19 —

Wiring the Heat Exchangers:

1. Run two 18-gauge wires, red for (+) and black for (-),

from each particular heating zone’s heat exchanger to

the electronic controller. Reference Figure 21.

2. Label the wires indicating the heating zone they per-

tain to (e.g., Living Room, Bathroom, Bedroom, etc.).

3. Insert all heat exchanger wires into the appropriate

terminal/heating zone location on the electronic con-

troller. Reference Figure 20 and Appendix A.

4. Wire all heat exchangers in a zone in-series. Refer-

ence Figure 21 and Appendix A.

5. Connect all electronic controller wires to the positive

and negative leads of the heat exchanger. Reference

Figures 21 and 22.

Burner - O

Burner - I

SECTION 3: HYDRONIC HEATING SYSTEM

When wiring the heat exchangers in-parallel, the main 18-

gauge wire is split to allow the heat exchanger wires to

combine with the main wire to be powered or grounded,

respectively.

Figure 22

— Page 20 —

Figure 21

To Appropriate Terminal on the

Electronic Controller Board

(Appendix A)

To Appropriate Terminal on the Electronic

Controller Board (Appendix A)

Page is loading ...

Aqua-Hot AHE-400-P01 Installation guide

This manual is also suitable for

Aqua-Hot AHE-400-P01 Installation guide

Related papers

Other documents