2. Advantech
  3. DLoG XMT 5 Series

Advantech DLoG XMT 5 Series Quick Start

  • Hello! I am an AI chatbot trained to assist you with the Advantech DLoG XMT 5 Series Quick Start. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
Prepare / Switch on XMT 5
Quickstart
XMT 5 Series
Tip: Congure the XMT 5 before fastening it to machines or vehicles, because in
this way software conguration for the WLAN function, for Automatic switch-off, etc.
is signicantly simpler and more convenient.
Prerequisites:
• Advantech-DLoG power supply cable
• Advantech-DLoG Preconverter (a special table supply power unit),
to connect the XMT 5 to an AC power supply.
The Preconverter is specially prepared to simulate a vehicle’s
ignition signal: DC+ and Ign are connected with the +Pole of the power supply.
• If you want to operate the XMT 5 using an external mouse or
keyboard, connect this before switching on the device.
3
Rotate Screen and Admin Tools
2
Conguration with neXt Cong
Power supply / Switch on the device
• Connect the XMT 5 to the power supply using an Advantech-DLoG Preconverter.
• Press the <Power>-key (for a short time; max. 1 second).
• The XMT 5 will start.
You can open the Rotate Screen and Admin Tools (manage user rights) functions
via the XMT 5 context menu.
• The context menu can be opened on the XMT 5 screen with the
right mouse button or by pressing the touch screen (min. 2 sec.).
The following functions and others are available:
• Rotate Screen – To rotate the current display
• Admin Tools | Recalibrate Touch – To recalibrate the touch screen
• Don‘t forget: SaveRegistry must be executed to save new calibration data.
• Admin Tools | Enter Admin Mode
The Enter Admin Mode function
opens the XMT 5 Security Shell.
The Security Shell is used to protect
the system against unintended changes
by standard users.
Caution: You must restart the computer
after setting up the security shell.
!
Notice: The XMT 5 series is equipped with an integrated, galvanic isolated power
supply for direct voltage. 12/24 VDC and 24/48 VDC models are available.
The output voltage of the Preconverter must be compatible with the input voltage
of the XMT 5. If it is not, the XMT 5 may become badly damaged.
Preconverter and Power supply
cable for XMT 5 Series
XMT 5 Series: XMT 5/7 and XMT 5/10
Your XMT 5 is equipped with the conguration program „DLoG neXt Cong“. You can de-
ne the display brightness, automatic switch-off and front key assignment and other settings
with this program.
Only system administrators may congure the XMT 5.
a) Log on as an administrator
• Click the green neXt Cong icon in the task bar:
NeXt Cong will start.
• Open the menu item Advanced | Change Mode.
• Click Change Mode.
• Switch to Admin Mode. The passwort is: „gold“
• Save the setting.
The neXt Cong icon in the task bar will now be yellow.
Admin Mode is active.
You can now congure the automatic switch-off and the front keys.
b) Congure the automatic switch-off function
Each XMT 5 has been equipped with an automatic shutdown function. This function has
already been pre-congured and governs the power-up and shutdown procedures for the
XMT 5 connected to a car ignition.
The precongured settings for each XMT 5 must be adapted for each customer.
• Open the Switch-Off menu in neXt Cong.
• Check and congure the settings.
• Save your settings
c) Program the keys on the front of the XMT 5
• Open the Set Front Keys menu in neXt Cong.
An interactive graphic appears with the available keys for the XMT 5.
• You can assign specic keyboard commands or program requests
to the front keys there.
• Save your settings
Tip: The Set Front Key settings for an XMT 5 can be exported as a cong le and copied
quickly and easily to other devices. You can nd more details in the XMT 5 manual
(available from the Advantech-DLoG Download Center).
!
Notice: If the XMT 5 is congured for switching on with an ignition signal, the
ignition signal must be connected to the power supply plug.
6
Electrical installation
7
Cable cover and strain relief
8
Further information
Notice:
• Ensure that the ground connection is correct!
• Choose a suitable position on the forklift for the ground connection.
• Sometimes the position from which the ground signal is to come is
specied by the vehicle manufacturer
• Position and connect the XMT 5 as close to the battery as possible.
• Do not attach the XMT 5 directly to a connector for a high-powered consumer
(e.g. an inverter for fork lift motors) as this could lead to
restarts, malfunctions or damage to the device.
• Some forklifts have a chassis that is connected to DC+.
Therefore, the XMT 5 chassis is also connected to DC+.
However, if you use peripheral devices that supply DC- to the
DLoG MTC 6 via an interconnector (such as a DC- serial port),
this will cause a short circuit. This will inevitably lead to malfunctions
or even a total system failure.
5
Mechanical installation
Position of the XMT 5 on the vehicle
• The driver‘s eld of vision in the vehicle must not be obstructed.
• If you want to install a keyboard and scanner on the side of the XMT 5,
please allow enough space.
Overview of the installation steps
Before you mount the XMT 5 onto the vehicle:
• The automatic switch-off function must be congured.
• The forklift must be prepared (connection to ignition, observe correct voltage, etc.).
We recommend that the installation process is carried out in the following sequence:
• Step 1: Secure the mounting bracket onto the vehicle
• Step 2: Attach the XMT 5 to the mounting bracket; please observe the assembly
instructions that come with the relevant mounting kit.
4
Wireless networks
The XMT 5 optionally contains a Summit WLAN card. Generally, the WLAN prole is set as
default in the factory by Advantech-DLoG for this card. If any adjustments are required, the
Summit Client Utility tool for modifying the WLAN prole is available.
Summit Client Utility Program
• Start the Summit Client Utility program with the SCU-Icon on the desktop.
• Log on with the password „SUMMIT“ (all uppercase).
• Make the desired settings.
Tip: Use the help function for this program to read details about the setting options.
!
Notice: WLAN settings may be made only by
qualied technical staff.
!
User manuals / device drivers in the Download Center
Manuals and the latest device drivers for your Advantech-DLoG industrial PC can
be found in the Downloads menu at www.advantech-dlog.com.
If you have any further questions, please contact your Advantech-DLoG service partner or
contact us directly at:
DLoG GmbH [email protected]
Industriestraße 15 www.advantech-dlog.com
D-82110 Germering Phone: (+49) 89 / 41 11 91 - 999
Ground bolt
XMT 5 connectors,
24/48 VDC
XMT 5 connectors,
12/24 VDC
Once the XMT 5 and mounting bracket have been secured:
• Prepare the strain relief.
• Position the cables on the stress relief rail so that they will
t through the openings in the cable cover.
• Mount the cables loosely on the strain relief rail.
Final steps:
• Fix the cables to the strain relief rail.
• Close the cable cover carefully, observing the assembly instructions provided
with the XMT 5.
Example for cable positioning
to the strain relief rail
Copyright 2011 by DLoG GmbH, Industriestraße 15, D-82110 Germering. All rights reserved.
Information in this document is subject to change without prior notice.
Quickstart Guide XMT 5 Series V1.00 DAN 885904E.00
/