Kawasaki KFX 450R - BROCHURE 2009 User manual

KFX450R

All Terrain Vehicle

Service Manual

This quick reference guide will assist

you in locating a desired topic or pro-

cedure.

•Bend the pages back to match the

black tab of the desired chapter num-

ber with the black tab on the edge at

each table of contents page.

•Refer to the sectional table of contents

for the exact pages to locate the spe-

cific topic required.

Quick Reference Guide

General Information 1

j

Periodic Maintenance 2

j

Fuel System (DFI) 3

j

Cooling System 4

j

Engine Top End 5

j

Engine Right Side 6

j

Engine Lubrication System 7

j

Engine Removal/Installatio n 8

j

Crankshaft/Transmission 9

j

Wheels/Tires 10

j

Final Drive 11

j

Brakes 12

j

Suspension 13

j

Steering 14

j

Frame 15

j

Electrical System 16

j

Appendix 17

j

KFX450R

All Terrain Vehicle

Service Manual

transmitted in any form or by any means, electronic mechanical photocopying, recording or otherwise,

without the prior written permission of Quality Assurance Division/Consumer Products & Machinery

Company/Kawasaki Heavy Industries, Ltd., Japan.

No liability can be accepted for any inaccuracies or omissions in this publication, although every possible

care has been taken to make it as complete and accurate as possible.

The right is reserved to make changes at any time without prior notice and without incurring an obligation

to make such changes to products manufactured previously. See your dealer for the latest information on

product improvements incorporated after this publication.

All information contained in this publication is based on the latest product information available at the time

of publication. Illustrations and photographs in this publication are intended for reference use only and may

not depict actual model component parts.

LIST OF ABBREVIATIONS

A ampere(s) lb pounds(s)

ABDC after bottom dead center m meter(s)

AC alternating current min minute(s)

ATDC after top dead center N newton(s)

BBDC before bottom dead center Pa pascal(s)

BDC bottom dead center PS horsepower

BTDC before top dead center psi pound(s) per square inch

°C degree(s) Celcius r revolution

DC direct current rpm revolution(s) per minute

F farad(s) TDC top dead center

°F degree(s) Fahrenheit TIR total indicator r eading

ft foot, feet V volt(s)

g gram(s) W watt(s)

h hour(s) Ω ohm(s)

L liter(s)

COUNTRY AND AREA CODES

AU Australia EUR Europe

CA Canada US United States

EMISSION CONTROL INFORMATION

To protect the environment in which we all live, Kawasaki has incorporated crankcase em ission

(1) and exhaust emission (2) control systems in compliance with applicable regulations of the

United States Environmental Protection Agency and California Air Resources Board.

Additionally, Kawasaki has incorporated an evaporative emission control system (3) in compli-

ance w ith applicable regulations of the United States Environmental Protection Agency.

1. Crankcase Emission Control System

A sealed-type crankcase emission control system is used to eliminate blow-by gases. The blow-by

gases are led to the breather chamber through the crankcase. Then, it is led to the air cleaner. Oil is

separated from the gases while passing through the inside of the breather chamber from the crankcase,

and then returned back to the bottom of crankcase.

2. Exhaust Emission Control System

This system reduces the amount of pollutants discharged into the atmosphere by the exhaust of this

vehicle. The f uel, ignition and exhaust systems of this vehicle have been carefully design

ed and con-

structed to ensure an efficient engine with low exhaust pollutant levels.

A maintenance free ignition system provides the most favorable ignit

ion timing and helps maintain a

thorough combustion process within the engine which contributes to a reduction of exhaust pollutants

entering the atmosphere.

The Clean Air Act, which is the Federal law covering motor vehicle pollution, contains what is com-

monly referred to as the Act’s "tampering provisions."

"Sec. 203(a) The following acts and the causing thereof are prohibit

ed...

3. Evaporative Emission Control System

The evaporative emission control system for this vehicle consists of low permeation fuel hoses and a

fuel tank.

(3)(A) for any person to remove or render inoperative any device or element of design installed

on or in a motor vehicle or motor vehicle engine in compliance with regulations under this

title prior to its sale and delivery to the ultimate purchaser, or for any m anufacturer or dealer

knowingly to remove or render inoperative any such device or element of design after such

sale and delivery to the ultimate purchaser.

(3)(B) for any person engaged in the business of repairing, servicing, selling, leasing, or trading

motor vehicles or motor vehicle engines, or who operates a fleet of motor vehicles know-

ingly to remove or render inoperative any device or element of design installed on or in a

motor vehicle or motor vehicle engine in compliance with regulations under this title follow-

ing its sale and delivery to the ultimate purchaser..."

NOTE

○

The phrase "remove or render inoperative any device or element of design" has been generally

interpre ted as f ollows:

1. Tampering does not include the temporary removal or render ing inoperative of de-

vices or elements of desig n in order to perform maintenance.

2. Tampering could include:

a.Maladjustment of veh icle components such that the emission standards are e x-

ceeded.

b.Use of replacement parts or acces

sories which adversely affect the performance

or durability of the vehicle.

c.Addition of components or accessories that result in the vehicle exceeding the stan-

dards.

d.Permanently removing, disconnectin g, or rendering inoperative any component or

element of design of the emission control systems.

WE RECOMMEND THAT ALL DEALERS OBSERVE THESE PROVISIONS OF FEDERAL LAW,

THE VIOLATION OF WHICH I S PUNISHABLE BY CIVIL PENALTIES NOT EXCEEDING

$10,000 PER VIOLATION.

PLEASE DO NOT TAMPER WITH NOISE CONTROL SYSTEM

(US MODEL only)

TAMPERING WITH EMISSION CONTROL SYSTEM PROHIBITED:

Federal regulations and California State law prohibit the following acts or the causing thereof:

(1) the removal or rendering inoperative by any person other than for purposes of maintenance,

repair, or replacement, of any device or element of design incorporated into any new vehicle for

the purposes of emission control prior to its sale or delivery to the ultimate purchaser or while it

is in use, or (2) the use of the vehicle after such device or element of design has been removed

or rendered inoperative by any person.

Do not tamper with the original emission related parts:

•

Throttle body or internal parts

•

Spark plug

•

Magneto ignition system

•

Fuel pump/Fuel injector

•

Air cleaner element

•

Electronic control unit (ECU)

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:

Federal law prohibits the following acts or the causing thereof: (1) the removal or rendering

inoperative by any person other than for purposes of maintenance, repair, or replacement, of any

device or element of design incorporated into any new vehicle for the purpose of noise control

prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the

vehicle after such device or element of design has been removed or rendered inoperative by

any person.

Among those acts presumed t o constitute tampering are the acts listed below:

* Replacement of the original exhaust system or muffler with a component not in com pliance

with Federal regulations.

* Removal of the muffler or any internal portion of the muffler.

* Removal of the air cleaner housing or air cleaner housing cover.

* Modifications to the muffler or air intake system by cutting, drilling, or other means if such

modifications result in increased noise levels.

* Modification to the air cleaner element.

Foreword

This manual is designed primarily for use by

trained mechanics in a properly equipped shop.

However, it contains enough detail and basic in-

formation to make it useful to t he owner who de-

sires to perform his own basic maintenance and

repair work. A basic knowledge of mechanics,

the proper use of tools, and workshop proce-

dures must be understood in order to carry out

maintenance and repair satisfactorily. When-

ever the owner has insufficient experience or

doubts his ability to do the work, all adjust-

ments, maintenance, and repair should be car-

ried out only by qualified mechanics.

In order to perform the work efficiently and

to avoid costly m istakes, read the text, thor-

oughly familiarize yourself with the procedures

before starting work, and then do the work ca

re-

fully in a clean area. Whenever special tools or

equipment are specified, do not use makeshift

tools or equipment. Precision measurem

ents

can only be made if the proper instruments are

used, and the use of substitute tools may ad-

versely affect safe operation.

For the duration of t he warranty period,

we recommend that all repairs and scheduled

maintenance be performed in

accordance with

this service m anual. Any owner maintenance or

repair procedure not performed in accordance

with this manual may void

the warranty.

To get the longest life out of your vehicle:

•

Follow the Periodic Maintenance Chart in the

Service Manual.

•

Be alert for problems and non-scheduled

maintenance.

•

Use proper tools and

genuine Kawasaki Vehi-

cle parts. Special tools, gauges, and testers

that are necessary when servicing Kawasaki

vehicles are i

ntroduced by the Service Man-

ual. Genuine parts provided as spare parts

are listed in the Parts Catalog.

•

Follow the p

rocedures in this manual care-

fully. Don’t take shortcuts.

•

Remember to keep complete records of main-

tenance a

nd repair with dates and any new

parts installed.

How to Use This Manual

In this manual, the product is divided into

its major systems and these systems make up

the manual’s chapters. The Quick Reference

Guide shows you all of t he product’s system

and assists in locating their chapters. Each

chapter in turn has its own comprehensive Ta-

ble of Contents.

For example, i f you want ignition coil informa-

tion, use the Quick Reference Guide to locate

the Electrical System chapter. Then, use the

Table of Contents on the first page of the chap-

ter to find the Ignition Coil section.

Whenever you see these WARNING and

CAUTION symbols, heed their instructions!

Always follow safe operating and maintenance

practices.

WARNING

This warning symbol identifies special

instructions or procedures which, if not

correctly followed, could result in per-

sonal injury, or loss of life.

CAUTION

This caution symbol identifies special

instructions or procedures which, if not

strictly observed, could result in dam-

age to or destruction of equipment.

This manual contains four more symbols (in

addition to WARNING and CA UTION) w hi

ch will

help you distinguish different types of informa-

tion.

NOTE

○

This note symbol indicates points of par-

ticular interest for m ore efficient and con-

venient operation.

•

Indicates a procedural step or work to be

done.

○

Indicates a procedural sub-step or how to do

the work of the procedural step it follows. It

also precedes the te

xt of a NOTE .

Indicates a conditional step or what action to

take based on the results of the test or inspec-

tion in the proced

ural step or sub-step it fol-

lows.

In m ost chapters an exploded view illustration

of the system com

ponents follows the Table of

Contents. In these illustrations you will find t he

instructions indicating which parts require spec-

ified tighten

ing torque, oil, grease or a locking

agent during assembly.

GENERAL INFORMATION 1-1

1

General Information

Table of Contents

Before Servicing ..................................................................................................................... 1-2

Model Identification................................. ..................................... ..................................... ...... 1-7

General Specifications...................................................................................................... ...... 1-8

Unit Conversion Table ............................................................................................................ 1-11

1-2 GENERAL INFORMATION

Before Servicing

Before starting to perform an inspection service or carry out a disassembly and reassembly oper-

ation on a vehicle, read the precautions given below. To facilitate actual operations, notes, illustra-

tions, photographs, cautions, and detailed descriptions have been included in each chapter wherever

necessary. This section explains the items that require particular attention during the removal and

reinstallation or disassembly and reassembly of general parts.

Especially note t he following:

Battery Ground

Before completing any service on the vehicle, disconnect

the battery wires from the battery to prevent the engine from

accidentally turning over. Disconnect the ground wire (–)

first and then the positive (+). When completed with the

service, first connect the positive (+) wire to the positive

(+) terminal of the battery then the negative (–) wire to the

negative terminal.

Edges of Parts

Lift large or heavy parts wearing gloves to prevent injury

from possible sharp edges on the parts.

Solvent

Use a high-flush point so

lvent when cleaning parts. High

-flush point solvent should be used according to directions

of the solvent manufacturer.

Cleaning Vehicle before Disassembly

Clean the vehicle thoroughly before disassembly. Dirt or

other foreign materials entering into sealed areas during ve-

hicle disassembly can cause excessive wear and decrease

performance of the vehicle.

GENERAL INFORMATION 1-3

Before Servicing

Arrangement and Cleaning of Removed Parts

Disassembled parts are easy to confuse. Arrange the

parts according to the order the parts were disassembled

and clean the parts in order prior to assembly.

Storage of Removed Parts

After all the parts including subassembly parts have been

cleaned, store the parts in a clean area. Put a clean cloth

or plastic sheet over the parts to protect from any foreign

materials that may collect before re-assembly.

Inspection

Reuse of worn or damaged parts may lead to serious ac-

cident. Visually inspect removed parts for corrosion, discol-

oration, or other damage. Refer to the appropriate sections

of this manual for service limits on individual parts. Replace

the parts if any damage has been found or if the part is be-

yond its service limit.

Replacem ent Parts

Replacement Parts must be KAWASAK I genuine or

recommended by KAWASAKI. Gaskets, O-rings, Oil seals,

Grease seals, circlips or cotter pins must be replaced with

new ones whenever disassembled.

Assembly Order

In most cases assembly order is the reverse of disassem-

bly, however, if assembly order is provided in this Service

Manual, follow the procedures given.

1-4 GENERAL INFORMATION

Before Servicing

Tightening S equence

Generally, when installing a part with several bolts, nuts,

or screws, start them all in their holes and tighten them to

a snug fit. Then tighten them according to the specified se-

quence to prevent case warpage or deformation which can

lead to m alfunction. Conversely when loosening the bolts,

nuts, or screws, first loosen all of them by about a quar-

ter turn and then remove them. If the specified tightening

sequence is not indicated, tighten the fasteners alternating

diagonally.

Tightening Torque

Incorrect torque applied to a bolt, nut, or screw may

lead to serious damage. Tighten fasteners to the specified

torque using a good quality torque wrench.

Often, the tightening sequence is followed twice initial

tightening and final tightening with torque wrench.

Force

Use common sense during disas

sembly and assembly,

excessive force can cause expensive or hard to repair dam-

age. When necessary, remove screws that have a non

-permanent locking agent

applied using an impact driver.

Use a plastic-faced m allet whenever tapping is necessary.

Gasket, O-ring

Hardening, shrinkage, or damage of both gaskets

and O-rings after disassembly can reduce sealing per-

formance. Remove old gaskets and clean the sealing

surfaces thoroughly so that no gasket m aterial or other

material remains. Install new gaskets and replace used

O-rings when re-assembling.

Liquid Gasket, Locking Agent

For applications that require Liquid Gasket or a

Non-Permanent Locking A gent, clean the surfaces so

that no oil residue remains before applying liquid gasket

or locking agent. Do not apply them excessively. Exces-

sive application can clog oil passages and cause serious

damage.

GENERAL INFORMATION 1-5

Before Servicing

Press

For items such as bearings or oil seals that must be

pressed into place, apply small amount of oil to t he con-

tact area. Be sure to maintain proper alignment and use

smooth movements when installing.

Ball Bearing and Needle Bearing

Do not remove pressed ball or needle unless r emoval is

absolutely necessary. Replace with new ones whenever

removed. P ress bearings with the manufacturer and size

marks facing out. Press the bearing into place by putting

pressure on the correct bearing race as shown.

Pressing the incorrect race can cause pressure between

the i nner and outer race and result in bearing damage.

Oil Seal, Grease Seal

Do not remove pressed oil or grease seals unless removal

is necessary. Replace with new ones whenever removed.

Press new oil seals with manufacture and size marks facing

out. Make sure the seal is aligned properly when installing.

Apply specified grease to the lip of seal before installing

the seal.

Circlips, Cotter Pins

Replace circlips or cotter pins that were removed with new

ones. Take care not to open the clip excessively when in-

stalling to prevent deformation.

1-6 GENERAL INFORMATION

Before Servicing

Lubrication

It is important to lubricate rotating or sliding parts during

assembly to minimize wear during initial operation. Lubri-

cation points are called out throughout this manual, apply

the specific oil or grease as specified.

Direction of Engine Rotation

When rotating the crankshaft by hand, the free play

amount of rotating direction will affect the adjustment. Ro-

tate the crankshaft to positive direction (clockwise viewed

from output side).

Electrical Wires

A two-color wire is identifie

d first by the primary color and

then the stripe color. Unless instructed otherwise, electrical

wires must be connected to those of the same color.

Instrument

Use a meter that has enough accuracy for an accurate

measurement. Read the m anufacture’s instructions thor-

oughly before using the meter. Incorrect values may lead

to improper adjustments.

GENERAL INFORMATION 1-7

Model Identification

KSF450B8F Left Side View

KSF450B8F Right Side View

Frame Number

[A] Frame Number

[B] Left Suspension Arm

Engine Number

[A] Engine N umber

[B] Shift Pedal

1-8 GENERAL INFORMATION

General Specifications

Items KSF450B8F ∼, KSF450B8FA ∼

Dimensions

Overall Length 1 806 mm (71.10 in.)

Overall Width 1 170 mm (46.06 in.)

Overall Height 1 064 mm (41.89 in.)

Wheelbase 1 255 mm (49.41 in.)

Ground C learance 108 mm (4.25 in.)

Seat Height 786 mm (30.94 in.)

Dry Mass (KSF450B8F/B8FA) 165 kg (364 lb)

Curb Mass: (KSF450B9F (US, CA, AU)/B9FA) 178 kg (392 lb)

(KSF450B9F (EUR))179 kg (395 lb)

Front 88.5 kg (195 lb)

(KSF450B9F (EUR)) 89 kg (196 lb)

Rear 89.5 kg (197 lb)

(KSF450B9F (EUR)) 90 kg (198 lb)

Fuel Tank Capacity 10.0 L (2.64 US gal)

Performance

Minimum Turning Radius 3.6 m (11.8 ft)

Engine

Type 4-stroke, DOHC , Single-cylinder

Cooling System Liquid-cooled

Bore and Stroke 96.0 × 62.1 mm (3.78 × 2.44 in.)

Displacement 449 cm³ (27.4 cu in.)

Compression Ratio 12.0 : 1

Maximum Horsepower 31.9 kW (43 PS) @7 500 r/min (rpm), (US) -

Maximum Torque 41.9 N·m (4.3 kgf·m, 31 ft·lb) @7 000 r/min (rpm)

Carburetion System FI (Fuel Injection) Keihin 42

Starting System Electric Starter

Ignition System Battery and Coil (transistorized ignition)

Timing Advance Electronically advanced

Ignition Timing From 10° BTDC@1 800 r/min (rpm)

to 39.5° BTDC@6 000 r/min (rpm)

Spark Plug NGK CPR8EB-9

Valve Timing:

Inlet:

Open 26° BTDC

Close 70° ABDC

Duration 276°

Exhaust:

Open 82° BBDC

Close 24° ATDC

Duration 284°

GENERAL INFORMATION 1-9

General Specifications

Items KSF450B8F ∼, KSF450B8FA ∼

Lubrication System Forced lubrication (semi dry sump)

Engine oil:

Type

API SF or SG

API SH, SJ or SL wi th JASO MA, MA1 or MA2

Viscosity SAE 10W-40

Capacity 1.35 L ( 1.43 US qt)

Drive Train

Primary Reduction System:

Type Gear

Reduction Ratio 2.952 (62/21)

Clutch Type Wet, multi disc

Transmission:

Type 5-speed and reverse, constant mesh, return shift

Gear ratios:

1st 2.230 (29/13)

2nd 1.800 (27/15)

3rd 1.529 (26/17)

4th 1.278 (23/18)

5th 1.048 (22/21)

Reverse 2.364 (16/11 × 26/16)

Final Drive System:

Type Chain drive

Reduction Ratio

2.714 (38/14)

Overall Drive Ratio 8.395 @Top gear

Frame

Type Tubular, Double cradle

Caster (Rake Angle) 1.8°

Camber -2°

King Pin Angle 14.7°

Trail 7.6 mm (0.30 in.)

Tread:

Front 972 m m (38.27 in.)

Rear 899 m m (35.39 in.)

Front Ti re:

Type Tubeless

Size AT21 × 7-10

Rear Tire:

Type Tubeless

Size AT20 × 10-9

Rim Size:

Front 10 × 5.5

Rear 9×8

1-10 GENERAL INFORMATION

General Specifications

Items KSF450B8F ∼, KSF450B8FA ∼

Suspension:

Front:

Type Double Wishbone

Wheel Travel 215 mm (8.46 in.)

Rear:

Type Swingarm

Wheel Travel 254 mm (10.0 in.)

Brake:

Front Disc × 2

Rear Disc

Parking Brake Disc (Mechanical)

Electrical Equipment

Battery 12 V 6 Ah

Headlight:

Type Semi-sealed beam

Bulb 12 V 30/30 W × 2

Tail/brake Light:

Bulb 12 V 0.5/4.1 W (LED)

Alternator:

Type Three - phase AC

Rated Output 14 A, 14 V @5 000 r/min (rpm)

Specifications subject t o change without notice, and may not apply to every country.

Page is loading ...

Kawasaki KFX 450R - BROCHURE 2009 User manual

Kawasaki KFX 450R - BROCHURE 2009 User manual

Related papers

Other documents