Motorola DCT6416 Installation guide

Installation Manual

DCT6400 Phase III

High-Definition

DVR Cable Terminal

I

DC

T64

16 II

CAUTION

RISK OF ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

CAUTION:

Caution

These servicing instructions are for use by qualified personnel only. To reduce the risk of electrical shock, do not perform any servicing other

than that contained in the Installation and Troubleshooting Instructions unless you are qualified to do so. Refer all servicing to qualified service

personnel.

Special Symbols That Might Appear on the Equipment

This symbol indicates that dangerous voltage levels are present within the equipment. These voltages are not

insulated and may be of sufficient strength to cause serious bodily injury when touched. The symbol may also

appear on schematics.

The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important

installation, servicing, and operating instructions in the documents accompanying the equipment.

For continued protection against fire, replace all fuses only with fuses having the same electrical ratings

marked at the location of the fuse.

This equipment operates over the marked Voltage and Frequency range without requiring manual setting of any

selector switches. Different types of line cord sets may be used for connections to the mains supply circuit and should

comply with the electrical code requirements of the country of use. The line cord provided with the equipment is

acceptable for use with NEMA Style 5-15R ac receptacles supplying nominal 120 Volts.

WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,

SHALL BE PLACED ON THE APPARATUS.

CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE,

OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER CABLES.

It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damaging the

equipment by local lightning strikes and other electrical surges.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturers

instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Unplug this apparatus during lightning storms or when unused for long periods of time.

13 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

Caring for the Environment by Recycling

When you see this symbol on a Motorola product, do not dispose of the product with residential or commercial waste.

Recycling your Motorola Equipment

Please do not dispose of this product with your residential or commercial waste. Some countries or regions, such as the

European Union, have set up systems to collect and recycle electrical and electronic waste items. Contact your local

authorities for information about practices established for your region. If collection systems are not available, call

Motorola Customer Service for assistance.

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his/her own expense. Any changes or modifications not expressly approved

by Motorola could void the user’s authority to operate this equipment under the rules and regulations of the FCC. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

 Re-orient or relocate the receiving antenna

 Increase the separation between the equipment and receiver

 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

You may find the following booklet, prepared by the Federal Communication Commission, helpful: How to Identify and Resolve Radio-TV

Interference Problems, Stock No. 004-000-0342-4, U.S. Government Printing Office, Washington, DC 20402.

Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

FCC Declaration of Conformity

According to 47 CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with

Class B Personal Computers, Motorola, Inc., 6450 Sequence Drive, San Diego, CA 92121, 1-800-225-9446 or 101 Tournament Drive,

Horsham, PA 19044, 1-888-944-4357, declares under sole responsibility that the product identifies with 47 CFR Part 2 and 15 of the FCC Rules

as a Class B digital device. Each product marketed is identical to the representative unit tested and founded to be compliant with the standards.

Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity

production and testing on a statistical basis as required by 47 CFR 2.909. Operation is subject to the following condition: This device must

accept any interference received, including interference that may cause undesired operation. The above named party is responsible for

ensuring that the equipment complies with the standards of 47 CFR, Paragraphs 15.107 to 15.109

Canadian Compliance

This Class B digital device complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the

building, as close as possible to the point of cable entry as practical.

translation, transformation or adaptation) without written permission from Motorola, Inc.

Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola

to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed,

including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or

changes in the product(s) described in this manual at any time.

MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Dolby Digital manufactured under license from

Dolby Laboratories Licensing Corporation. Dolby, Dolby Digital, ProLogic and the double-D symbol are registered trademarks of Dolby

Laboratories Licensing Corporation. DOCSIS is a registered trademark of Cable Television Laboratories, Inc. This device incorporates a

copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of the copyright protection

technology is granted by Macrovision for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited. Macrovision is a registered trademark of Macrovision Corporation. HDMI, the HDMI logo and High-

Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

All other product or service names are the

property of their respective owners. © Motorola, Inc. 2005

Contents

Section 1

Introduction

Features ............................................................................................................................................................................................ 1-2

Tuners ...................................................................................................................................................................................... 1-2

Standard Audio/Video Features............................................................................................................................................. 1-2

Standard DVR Functionality................................................................................................................................................... 1-3

Standard Data Features.......................................................................................................................................................... 1-3

Standard Miscellaneous Features ......................................................................................................................................... 1-3

Available Optional Features................................................................................................................................................... 1-4

Using This Manual ........................................................................................................................................................................... 1-4

Related Documentation................................................................................................................................................................... 1-4

Document Conventions................................................................................................................................................................... 1-4

If You Need Help............................................................................................................................................................................... 1-5

Calling for Repairs ........................................................................................................................................................................... 1-6

Section 2

Overview

Front Panel ....................................................................................................................................................................................... 2-1

Rear Panel......................................................................................................................................................................................... 2-2

Section 3

Installation

Important Safety Considerations ................................................................................................................................................... 3-1

During Transportation to the Subscriber Home................................................................................................................... 3-1

During Installation................................................................................................................................................................... 3-1

Before You Begin ............................................................................................................................................................................. 3-2

Clearing the Hard Drive .......................................................................................................................................................... 3-2

Video Connection Options ..................................................................................................................................................... 3-3

Audio Connection Options..................................................................................................................................................... 3-3

Installation Overview ....................................................................................................................................................................... 3-4

Cabling to an HDTV for Video......................................................................................................................................................... 3-5

Cabling to an HDTV and an A/V Receiver............................................................................................................................. 3-6

Cabling to a Standard Definition TV and an A/V Receiver .................................................................................................. 3-7

Cabling to a Standard Definition TV and Audio Receiver ................................................................................................... 3-8

Installing the Optional IR Blaster ................................................................................................................................................... 3-9

Locating the IR Receiver on the VCR.................................................................................................................................... 3-9

Connecting the IR Blaster .................................................................................................................................................... 3-10

Checking the IR Blaster........................................................................................................................................................ 3-10

DCT6400 Phase III Installation Manual

ii Contents

Data Device Connections ..............................................................................................................................................................3-11

Boot Cycle.......................................................................................................................................................................................3-12

Boot Cycle Error Codes ........................................................................................................................................................3-13

Operational Check for the Remote Control..................................................................................................................................3-14

Optimizing the High-Definition Settings.......................................................................................................................................3-15

Graphics Overlaying the Video .....................................................................................................................................................3-17

Section 4

Diagnostics

Using the Diagnostics......................................................................................................................................................................4-2

d01 General Status ...........................................................................................................................................................................4-3

d02 Purchase Status ........................................................................................................................................................................4-4

d03 Out-Of-Band (OOB) Status .......................................................................................................................................................4-5

d04 In-Band Status ...........................................................................................................................................................................4-6

d05 Unit Address ..............................................................................................................................................................................4-8

d06 Current Channel Status ..........................................................................................................................................................4-10

d07 RF Modem (Upstream) ............................................................................................................................................................4-13

d08 Code Modules..........................................................................................................................................................................4-14

d09 Memory Configuration ............................................................................................................................................................4-16

d10 Keypad - LED ...........................................................................................................................................................................4-16

d11 Interface Status........................................................................................................................................................................4-17

d12 User Setting Status .................................................................................................................................................................4-19

d13 DVR/Hard Drive Status............................................................................................................................................................4-21

d14 DOCSIS Status.........................................................................................................................................................................4-23

d15 Application Specific Information ...........................................................................................................................................4-27

d16 Interactive Status ....................................................................................................................................................................4-27

Section 5

Troubleshooting

Appendix A

Specifications

Appendix B

Connection Record

Abbreviations and Acronyms

DCT6400 Phase III Installation Manual

Contents iii

Figures

Figure 1-1 DCT6400 front and rear views ..................................................................................................................................... 1-1

Figure 2-1 Front panel ..................................................................................................................................................................... 2-1

Figure 2-2 Rear panel...................................................................................................................................................................... 2-2

Figure 3-1 Cabling to an HDTV ...................................................................................................................................................... 3-5

Figure 3-2 Cabling to an HDTV and audio/video receiver........................................................................................................... 3-6

Figure 3-3 Cabling to a standard-definition stereo TV ................................................................................................................ 3-7

Figure 3-4 Cabling an audio receiver ............................................................................................................................................ 3-8

Figure 3-5 IR transmitter installed in mounting bracket ............................................................................................................. 3-9

Figure 3-6 IR Blaster installed ..................................................................................................................................................... 3-10

Figure 3-7 Sample data devices you can connect to the DCT6400.......................................................................................... 3-11

Figure 4-1 Example of the LED for the main menu...................................................................................................................... 4-2

Figure 4-2 Example GENERAL STATUS LED (no error) ............................................................................................................. 4-3

Figure 4-3 LED display for PURCHASE STATUS diagnostic...................................................................................................... 4-4

Figure 4-4 LED display for the OOB diagnostic........................................................................................................................... 4-5

Figure 4-5 LED display for in-band diagnostic ............................................................................................................................ 4-6

Figure 4-6 LED display of a unit address ..................................................................................................................................... 4-8

Figure 4-7 Current channel status LED displays....................................................................................................................... 4-10

Figure 4-8 RF upstream modem LED display ............................................................................................................................ 4-12

Figure 4-9 LED display for code modules .................................................................................................................................. 4-13

Figure 4-10 Interactive Info LED display..................................................................................................................................... 4-22

Figure B-1 Connection record .......................................................................................................................................................B-1

Tables

Table 1-1 DVR Recording Time Guidelines ................................................................................................................................... 1-3

Table 2-1 Front panel ...................................................................................................................................................................... 2-1

Table 2-2 Rear panel connections................................................................................................................................................. 2-3

Table 3-1 LED displays and OOB frequencies........................................................................................................................... 3-12

Table 3-2 Boot cycle error codes ................................................................................................................................................ 3-13

Table 3-3 Operational check ........................................................................................................................................................ 3-14

Table 3-4 Modes supporting graphics overlay........................................................................................................................... 3-17

DCT6400 Phase III Installation Manual

Section 1

Introduction

This manual provides instructions for cable operator personnel to install the Motorola DCT6400

Phase III high-definition digital video recorder (DVR) cable terminals. The DCT6400 Phase III

terminals include a high-end processor, expanded memory, and enhanced graphics to support

digital, on-demand, and analog broadcast and interactive services. They provide a full

complement of interconnection options.

The DCT6400 Series includes the DCT6412 and DCT6416 Phase III, collectively referred to in

this manual as the “DCT6400.”

They DCT6400 Series advanced capabilities, including:

 Authorization and purchase of on-demand programming

 High-definition television (HDTV) video decoding

 HDTV output through component video (Y Pb Pr), High-Definition Multimedia Interface

™

(HDMI

™

), or IEEE 1394 Firewire

 Surround-sound audio through a variety of analog and digital interconnection options

 Dual-tuner DVR functionality to pause and time shift live video and seamlessly record in

conjunction with the interactive programming guide (IPG)

 Built-in DOCSIS

®

cable modem

 Ethernet and Universal Serial Bus (USB) 2.0 ports for future home networking applications

 Adaptability to various software platforms

As with all Motorola digital cable terminals, the hardware features are enabled by core

operating and third party application software.

Figure 1-1

Front and rear views

INFO OPTION

MENUGUIDE

POWER SELECT

C

H

A

N

E

L

C

U

R

S

O

R

SMART CARD

P

MUTE

MSGS.

ON REMOTE

RECORD

USB 2.0 VI DEO IN L AUDIO IN R

Dual Tuner DVR / HDTV Capable

DCT6416 II I

RF IN 2

L

AUDIO

IN

AUDIO

OUT

R

OPTICAL

SPDIF

S-VIDEO

IR

RF OUT

RF IN 1

RPT OUT

CM IN

CABLE

IN

SWITCHED

105-125V

60Hz

4A MAX

500W MAX

IEEE

1394

TV PASS CARD

SATA

ETHERNET

HDMI

Pr

OUT

VIDEO

Pb

Y

IN

SPDIF

DCT6400 Phase III Installation Manual

1-2 Introduction

Features

Tuners

Two 54 to 860 MHz video tuners with analog AMS-VSB and digital MPEG-2 main profile high

level video processor

One dedicated tuner for the DOCSIS high-speed data/voice services channel, up to 860 MHz

One dedicated tuner for the out-of-band (OOB) control channel

Standard Audio/Video Features

ITU standard 64/256 QAM/FEC/enhanced adaptive equalizer

Clear analog channel processor with BTSC decoder

DES based encryption/DCII access control

Out-of-band data receiver (70-130 MHz) 2.048 Mbps

Audio/video input ports (front and rear)

Analog/digital video scaling (picture in graphics)

32-bit 2D/3D graphics support in hardware

Macrovision

®

copy protection

High-definition video output through:

 HDMI (also compatible with DVI using an HDMI-to-DVI converter cable)

 Component Video (Y Pb Pr)

 IEEE 1394

Standard-definition video output through:

 S-Video

 Baseband

 RF

Audio output through:

 S/PDIF ATSC standard Dolby Digital® AC-3 electrical or optical

 Baseband L/R

DCT6400 Phase III Installation Manual

Introduction 1-3

Standard DVR Functionality

DVR functionality integrated with the IPG enables subscribers to:

 Pause, rewind, fast-forward, or record live TV

 Maintain a personal recorded program library and access it using the IPG

 Select programs to record across multiple channels and time slots

 Rewind and replay recorded programs

 Simultaneously watch two programs, switching easily between them using the

SWAP key

 Record a program in the background while viewing another live program

 Simultaneously record programs from two channels while watching a different pre-recorded

program, with the ability to switch viewing between any of the three programs

Motorola cannot guarantee the exact amount of programming that each subscriber will be able to

record. The approximate time depends on the programming type and the drive size:

Table 1-1

DVR Recording Time Guidelines

Estimated Recording Hours For

Model Drive Size

Analog

Channels

Standard Digital

Channels

HDTV

Channels

DCT6412

120 GB 24 to 32 38 to 73 10 to 15

DCT6416

160 GB 35 to 43 55 to 100 14 to 21

All times are approximate. The actual hours a subscriber can record are a function of program

bit rate, the IPG type, and the reserved buffer space. A SATA port is available to connect an

external drive to add DVR recording capacity.

Standard Data Features

Integrated DOCSIS 1.0/1.1 capable cable modem

16 MB flash memory

128 MB SDRAM

One rear and one front Universal Serial Bus (USB) 2.0 port (dual connector interface)

10/100 Base-T Ethernet Port (RJ-45)

On-board real-time RF return (DOCSIS compliant)

Renewable security connector

Standard Miscellaneous Features

Smart Card interface for electronic commerce

Infra-Red (IR) blaster port

Switched accessory outlet

Messaging capabilities

DCT6400 Phase III Installation Manual

1-4 Introduction

Digital diagnostics

Full feature access from front panel using a four-digit, seven-segment LED display

Available Optional Features

Factory-installed expansion flash memory (32 MB)

IR Blaster transmitter

Using This Manual

This manual provides instructions to install and configure a DCT6400:

Section 1 Introduction provides a product description, a list of related documentation, the technical

help line telephone number, and the repair/return procedure.

Section 2 Overview describes the DCT6400 and provides an overview of its use. This section also

identifies the front-panel displays and keys and describes the rear-panel features.

Section 3 Installation provides subscriber location installation and testing instructions.

Section 4 Diagnostics provides instructions on accessing and interpreting the built-in diagnostics.

Section 5 Troubleshooting provides information on common error conditions and their resolution.

Appendix A Specifications provides the technical specifications.

Appendix B Connection Record provides a diagram for recording the connections between the

DCT6400 and other devices.

Abbreviations

and Acronyms

The Abbreviations and Acronyms list contains the full spelling of the short forms used in

this manual.

Related Documentation

The following documentation may be helpful when operating the DCT6400:

 DCT6400 Phase III User Guide

 User documentation for the remote control, audio receiver, TV, and other components

Separate instruction manuals are available for associated components.

Document Conventions

Before you begin working with this manual, familiarize yourself with the following stylistic

conventions:

SMALL CAPS

Denotes silk screening on the equipment, typically representing front- and rear-panel

controls, input/output (I/O) connections, and LEDs

* (asterisk)

Indicates that several versions of the same model number exist and the information applies

to all models; when the information applies to a specific model, the complete model number

is given

Italic type

Used for emphasis

Courier font

Displayed text

DCT6400 Phase III Installation Manual

Introduction 1-5

If You Need Help

If you need assistance while working with the DCT6400, contact the Motorola Technical

Response Center (TRC):

 Inside the U.S.: 1-888-944-HELP (1-888-944-4357)

 Outside the U.S.: 1-215-323-0044

 Motorola Online:

http://businessonline.motorola.com

The TRC is on call 24 hours a day, 7 days a week. In addition, Motorola Online offers a

searchable solutions database, technical documentation, and low-priority issue creation and

tracking.

Http://businessonline.motorola.com888-944-4357 / 215-323-0044 / 888-944-HELP

Data Networks/

Transmission Products

PRESS 3

Products

PRESS 1

Cable Router

VOIP

PRESS 2

Cable Modems

Products

PRESS 3

Transmission

Transport

Products

(MBT/MWT/MEA)

PRESS 5

Multiservice

Management

PRESS 4

Network

Licensing

PRESS 1

Network

Management

Products

PRESS 2

Network

Technical Response Center

Telephone Menu Options

Connected Home Solutions

Video Products

PRESS 1

Issued: 03/2005

Consumer

Support

PRESS 4

Broadcaster,

Satellite IRD or

Encoder Products

PRESS 2

Severity Level

1 - Critical Failure

2 - Serious Failure

3 - Non-Serious Failure

4 - Escalated Support

5 - Technical Assistance

PRESS 3

Settops

PRESS 2

Headend

PRESS 1

Controllers

PRESS 2

Analog

PRESS 1

Digital

IRD

PRESS 1

Commercial

Encoder

PRESS 2

Uplink

Modem

PRESS 2

Cable

PRESS 3

DCP

Satellite

C Band

PRESS 1

Consumer

DCT6400 Phase III Installation Manual

1-6 Introduction

Calling for Repairs

If a Motorola DCT6xxx set-top requires repair service, please call one of the following Motorola

Authorized Service Centers:

Company

From USA

or Canada

Outside USA

or Canada

World Wide Digital

1-800-227-0450 1-956-541-0600

Teleplan

1-800-352-5274 1-302-322-6088

To ensure efficient service, request a Return for Service Authorization (RSA) number. Be sure to

display the RSA number prominently on all equipment boxes.

The Service Center will provide the shipping address of the location performing your repairs.

To ship your equipment for repair:

1 Pack the unit securely, if possible in its original factory shipping carton.

2 Print or display the RSA number so it is easily visible on all equipment boxes.

3 Enclose a note describing the exact problem. Complete and enclose the checklist provided

with the unit.

4 Ship the unit PREPAID to the address provided by the Service Center.

DCT6400 Phase III Installation Manual

Section 2

Overview

This section describes the front and rear panel.

Front Panel

The front panel controls provide functional navigation if the remote control is lost or is

temporarily out of service. Certain functions, such as those requiring a numeric entry, require a

remote control. Some connectors are not enabled and require the support of application software.

Figure 2-1

Front panel

INFO OPTION

MENUGUIDE

POWER SELECT

C

H

A

N

E

L

C

U

R

S

O

R

SMART CARD

P

MUTE

MSGS.

ON

REMOTE

RECORD

USB 2.0 VI DEO IN L AUDIO IN R

Dual Tuner DVR / HDTV Capable

DCT6416 II I

6

7

89 10111

2

13

12

3

4

5

Table 2-1

Front panel

Key Feature Function

1*

USB 2.0 USB 2.0 connector for devices such as keyboards, joysticks, scanners, disk storage, PCs,

printers, or digital cameras

2

*

VIDEO IN Accepts baseband video from a VCR, camcorder, or other video device

3

*

AUDIO IN L and R connectors Accept audio from a VCR, camcorder, or other audio device.

4 LED

Displays the channel number or time of day. The indicators are:

 MSGS. — the DCT6400 has received messages for you to read

 ON — the DCT6400 is powered on

 RECORD — the DVR is recording

 REMOTE — the remote control is in use

5

*

SMARTCARD Supports electronic commerce activity using a Smart Card

6

CURSOR Moves the cursor around the program guide and menu screens

7

MENU Displays the main menu

8

POWER Turns the unit on or off

9

INFO Displays the current channel and program information (not supported by all applications)

10

OPTION Reserved for future use.

11

SELECT Selects menu options or programs from the program guide

12

GUIDE Displays the program guide

13

CHANNEL Changes the channels by moving up or down

* These connectors are not enabled and require the support of the application software.

DCT6400 Phase III Installation Manual

2-2 Overview

Rear Panel

The rear panel contains a switched power outlet; connectors for video, audio, and RF cabling;

data output; and modem and data interface connectors. Some connectors are not enabled and

require the support of application software.

Figure 2-2

Rear panel

RF IN 2

L

AUDIO

IN

AUDIO

OUT

R

OPTICAL

SPDIF

S-VIDEO

IR

RF OUT

RF IN 1

RPT OUT

CM IN

CABLE

IN

SWITCHED

105-125V

60Hz

4A MAX

500W MAX

IEEE

1394

TV PASS CARD

SATA

ETHERNET

HDMI

Pr

OUT

VIDEO

PbY

IN

SPDIF

12 4 98

10

5

11 12 13 14 16 1817

3

76

15

Table 2-2

Rear panel connections

Key Item Function

1

CABLE IN F-type coaxial cable input

2

RF OUT RF video output

3

OPTICAL SPDIF Optical digital Dolby Digital 5.1 audio or PCM audio output

4*

AUDIO IN L and R (left and right) RCA connectors for loop-through audio from audio equipment

5

SPDIF Coaxial Dolby Digital 5.1 or PCM audio output

6*

VIDEO IN RCA type video input from a TV, VCR, camcorder, or other device

7

VIDEO OUT RCA type video output to a VCR or TV

8*

ETHERNET Ethernet 10/100Base-T port

9

AC power AC power connector:

 The bottom plug is an input for the AC power cord

 The top plug is a switched power outlet for a device such as a TV or VCR

10

IR Mini phono jack enabling the DCT6400 to control a VCR using an optional low power IR

Blaster transmitter (not all IPGs support this feature)

11

S-VIDEO

S-Video high quality video output to a VCR or TV that accepts S-Video

12

AUDIO OUT L and R (left and right) RCA type stereo audio output jacks

13

Y Pb Pr Component video output to an HDTV

14

HDMI HDMI video output to an HDTV (can connect to a DVI input using an HDMI-to-DVI

converter cable)

15

TV PASSCARD TV passcard interface

16*

USB USB 2.0 connector for devices such as keyboards, joysticks, scanners, disk storage, PCs,

printers, or digital cameras

17

SATA Connector for optional external hard drive

18

IEEE 1394 IEEE 1394 connector for connecting to audio and video devices such as a DTV.

* These connectors are not enabled and require the support of the application software

DCT6400 Phase III Installation Manual

Section 3

Installation

This section provides instructions to cable the DCT6400 and check its operation. The cabling

diagrams illustrate connections to high- or standard-definition TVs, home theater receivers, and

stereo VCRs.

Important Safety Considerations

The DCT6400 requires careful handling to avoid potential damage to its internal hard disk drive

or the loss of recorded data. Be sure to follow these requirements during transportation and

installation.

During Transportation to the Subscriber Home

Transport the cable terminal in its shipping box or an equally padded container.

Do not expose the terminal to rain or moisture.

During Installation

VENTILATE

INFO

OPTION

MENU GUIDE

POWER SELECT

C

H

A

N

E

L

C

U

R

S

O

R

SMART CARD

P

MUT E

MS G S .

ON REMOTE

RECORD

USB 2 .0 VIDEO IN L AUDIO IN R

Du a l T uner DV R / H DT V C ap a ble

DCT 6416 III

Do not place the cable terminal in an enclosed area where the cooling vents are blocked or

impede the flow of air through the ventilation openings.

Install the terminal so that its position does not interfere with its proper ventilation. For

example, do not place the terminal on a bed, sofa, rug, or similar surface that could block the

ventilation openings.

Install the terminal away from heat sources such as radiators, heat registers and stoves.

Installation of the terminal near consumer electronics devices, such as stereo

receiver/amplifiers and televisions, is permitted as long as the air surrounding the terminal

does not exceed 40º C (104º F).

Place the terminal on a flat surface not prone to vibration or impact.

Do not install the terminal in an area where condensation occurs.

To prevent the temporary loss of guide data and cause a temporarily non-responding terminal,

do not plug the AC power cord into a switched power outlet.

To avoid shock and vibration damage to the internal hard drive, do not move the terminal while

it is plugged in.

To allow the hard drive to spin down and park its heads, wait at least 10 seconds after

disconnecting power before moving the terminal.

DCT6400 Phase III Installation Manual

3-2 Installation

Before You Begin

Before you move or change components on the subscriber entertainment system:

 Review the installation instructions.

 Determine if you are connecting to a standard TV, a composite (baseband) monitor, or a

component monitor.

 Verify that you have the necessary cables and other required items.

 If the terminal was previously used, clear its hard drive before installing it at a new

subscriber location

Clearing the Hard Drive

On a previously-used cable terminal, delete all recorded programs from the hard drive before

installing it at a new subscriber location. This prevents your new subscriber from viewing

programming they may not have purchased or may not want to see.

To prevent subscribers from accidentally deleting all of their recorded programs, a specific set of

keystrokes is required to clear the hard drive. Having a TV connected is optional.

To clear the hard drive:

1 Start the Diagnostics as described in Section 4, “Diagnostics.”

d 01 is displayed on the

front-panel LED.

2 Using a remote control, within five seconds, press

REPLAY, MY DVR three times, and LIVE TV.

(On some remote controls, the

MY DVR key may be labeled “LIST.”)

If you correctly enter this key sequence in five seconds or less, the hard drive is cleared and

the front-panel LED displays

Clr.

3 If

Clr is not displayed, re-enter the key sequence in step 2

If

Clr is displayed, press any other key to reset the terminal, turn it off, and complete the

clearing process.

DCT6400 Phase III Installation Manual

Installation 3-3

Video Connection Options

Use the following guidelines to determine the best video connection for the subscriber home

entertainment system. To determine the available video inputs on the TV, check the manual

supplied with the TV or the TV itself.

The DCT6400 offers the following video outputs:

Component

(Y Pb Pr)

HDTV and

SDTV

The Y Pb Pr outputs provide component video, the most widely supported HD video

connection.

HDMI

or

IEEE 1394

HDTV and

SDTV

HDMI and IEEE 1394 offer higher quality HD video than component video. If the TV

has an HDMI or a DVI input, use the

HDMI output instead of the IEEE 1394 output.

HDMI and IEEE 1394 are video and audio connections. If you use HDMI or

IEEE 1394, no separate audio connection to the TV is required.

HDMI is compatible with DVI. If the TV has a DVI input, you can use an HDMI-to-

DVI converter cable to connect to the DCT6400

HDMI connector.

If you use IEEE 1394, on-screen graphics do not display.

S-Video

SDTV only If your TV has an S-Video input, use S-Video. S-Video is the highest quality

standard-definition video output on the DCT6400.

Video

(composite)

SDTV only If your TV does not have an S-Video input, use the composite video (

VIDEO) output.

RF

SDTV only If your TV only has a coaxial RF input, connect it to the DCT6400

RF OUT connector.

Audio Connection Options

Connect the stereo audio cable to the AUDIO R and L connectors on the DCT6400 and the audio

left and right connectors on the TV. If the equipment supports it, use the

OPTICAL SPDIF or

coaxial digital

SPDIF output instead of the AUDIO R and L outputs. In most cases, these outputs

offer better audio quality, including support for 5.1 Surround Sound.

When connecting to a home theater receiver, depending on its inputs, you can use the following

DCT6400 audio outputs:

OPTICAL SPDIF or

coaxial

SPDIF

If the receiver supports it, use the

OPTICAL SPDIF or coaxial SPDIF audio output to deliver

Dolby AC-3 audio to a Dolby Digital home theater receiver.

Baseband

AUDIO

R and L

If the audio receiver does not support Dolby Digital, use the baseband

AUDIO R and L

outputs to connect to the audio receiver.

The cabling diagrams show sample audio/video (A/V) connections to an audio receiver, where

the receiver functions as an A/V router. When connecting to an audio receiver, reference its

installation instructions for directions on connecting to baseband and S/PDIF ports.

The VCR and TV receive their A/V signals from the currently selected input device on the audio

receiver. This is important when the subscriber has another A/V device such as a DVD player, a

secondary VCR, a CD player, or other electronic component. We recommend connecting the TV to

the monitor output so on-screen menus for the receiver can be displayed. (In many cases the

receivers themselves have interactive on-screen menus).

DCT6400 Phase III Installation Manual

3-4 Installation

Installation Overview

1 Determine if you are connecting to a:

High-definition TV

or monitor

Use the component video (Y Pb Pr), HDMI, or IEEE 1394 outputs. No other video

connection supports HDTV.

Standard

definition TV

Connect the

S-VIDEO connector using an S-video cable or connect the composite

VIDEO connector using an RCA phono cable. If the TV only has a coaxial RF input,

connect it to the DCT6400

RF OUT connector.

2 Determine if you are connecting the audio to a home theater receiver or directly to the TV:

 For an HDMI or IEEE 1394 video connection, no additional audio connections to the TV

are required.

 If the receiver or TV has a S/PDIF input, use the

OPTICAL SPDIF or coaxial SPDIF outputs.

 Otherwise, use the baseband left and right

AUDIO OUT outputs.

3 Locate the cabling diagram(s) that best match the subscriber configuration.

4 Connect the audio and video cables in a manner matching that diagram.

5 Determine if you are connecting to a data device (see “Data Device Connections” in this

section). For installation details, refer to instructions included with the data device.

6 Connect the cable terminal to the coaxial cable wall outlet.

7 Perform the boot cycle, including the download to the terminal, as described in “Boot Cycle”

in this section.

8 Perform the operational check for the remote control.

9 Optimize the high-definition settings. See “Optimizing the High-Definition Settings” in this

section.

10 Verify that the appropriate configuration information has been downloaded using the

addressable controller, such as the DAC 6000.

DCT6400 Phase III Installation Manual

Installation 3-5

Cabling to an HDTV for Video

For HDTV video, for the best possible video quality:

 If the TV has an HDMI input, connect it to the DCT6400 HDMI output. If the TV has a DVI

input, you can connect it to the DCT6400 HDMI output using and HDMI-to-DVI converter

cable.

 If the TV has neither an HDMI nor a DVI input but has an IEEE 1394 input, connect it to

the DCT6400 IEEE 1394 output. If you use IEEE 1394, on-screen graphics do not display.

 Otherwise, use the component video (Y, Pb, and Pr) connectors.

Figure 3-1

Cabling to an HDTV

RF IN 2

L

AUDIO

IN

AUDIO

OUT

R

OPTICAL

SPDIF

S-VIDEO

IR

RF OUT

RF IN 1

RPT OUT

CM IN

CABLE

IN

SWITCHED

105-125V

60Hz

4A MAX

500W MAX

IEEE

1394

TV PASS CARD

SATA

ETHERNET

HDMI

Pr

OUT

VIDEO

PbY

IN

SPDIF

HDTV

DCT6400 Phase III

either / or

CABLE/

ANTENNA IN

IEEE 1394

Component

Vi de o Input

Y

Pb

Pr

Cable in

HDMI

Because HDMI and IEEE 1394 provide a video and audio output, no additional audio

connections to the TV are required if you use HDMI or IEEE 1394.

DCT6400 Phase III Installation Manual

Page is loading ...

Motorola DCT6416 Installation guide

This manual is also suitable for

Motorola DCT6416 Installation guide

Related papers

Other documents