Powerplus POWXG30010 Owner's manual

Brand: Powerplus

Model: POWXG30010

Type: Owner's manual

  POWXG30010  EN 
Copyright © 2017 VARO  P a g e  | 1  www.varo.com 
APPLICATION ................................................................................... 3 
OVERVIEW COMPONENTS (FIG. A) ............................................... 3 
PACKAGE CONTENT LIST .............................................................. 3 
SYMBOLS .......................................................................................... 4 
GENERAL SAFETY RULES.............................................................. 4 
1  Training ...................................................................................................................... 4 
2  Preparation ................................................................................................................ 4 
3  Operation ................................................................................................................... 5 
4  Maintenance and storage ......................................................................................... 5 
SAFETY WARNINGS GASOLINE .................................................... 6 
STARTING AND STOPPING INSTRUCTIONS................................. 6 
1  Starting instructions ................................................................................................. 6 
2  Stopping instructions ............................................................................................... 7 
OPERATING INSTRUCTIONS .......................................................... 7 
1  Holding the unit ......................................................................................................... 7 
2  Adjusting edger cutting depth.................................................................................. 7 
3  Tips for best edging results ..................................................................................... 7 
OIL AND FUEL INFORMATION ........................................................ 7 
1  Using fuel additives .................................................................................................. 8 
2  Recommended petrol................................................................................................ 9 
MAINTENANCE AND REPAIR INSTRUCTIONS ............................. 9 
1  Maintenance schedule .............................................................................................. 9 
2  Blade replacement .................................................................................................... 9 
3  Air filter maintenance.............................................................................................. 10 
3.1  Cleaning the air filter ................................................................................................. 10 
4  Replacing the spark plug ........................................................................................ 10 
CLEANING AND STORAGE ........................................................... 10 
1  Cleaning ................................................................................................................... 10 
2  Storage .................................................................................................................... 11 
3  Long term storage ................................................................................................... 11 

POWXG30010 EN

12 TECHNICAL DATA .......................................................................... 11

13 NOISE ............................................................................................... 12

14 WARRANTY ..................................................................................... 12

15 ENVIRONMENT ............................................................................... 13

16 DECLARATION OF CONFORMITY ................................................ 13

POWXG30010 EN

LAWN EDGE CUTTER 25.4CC

POWXG30010

1 APPLICATION

The lawn edge cutter is ideal for traditional hard surface edging along driveways, sidewalks as

well as landscaping tasks around the lawn. By raising the edge guide, the edger can be used

in the garden for such tasks as shaping borders, around trees and flowerbeds. Not suitable for

professional use.

WARNING! Read this manual and general safety instructions carefully

before using the appliance, for your own safety. Your power tool should

only be passed on together with these instructions.

2 OVERVIEW COMPONENTS (FIG. A)

1. On/off switch

2. Handle

3. Throttle

4. Edger blade

5. Blade shield

6. Spark plug

7. Air filter cover

8. Depth adjustment lever

9. Fuel cap

10. Choke lever

11. Primer bulb

3 PACKAGE CONTENT LIST

 Remove all packaging materials.

 Remove remaining packaging and transit supports (if existing).

 Check the completeness of the packing content.

 Check the appliance, the power cord, the power plug and all accessories for transportation

damages.

 Keep the packaging materials as far as possible till the end of the warranty period.

Dispose it into your local waste disposal system afterwards.

WARNING: Packing materials are no toys! Children must not play with

plastic bags! Danger of suffocation!

1x machine

1x manual

1x hexagon spanner

1x spark plug spanner

1x spanner 22/24

1x spanner 8/10

1x empty bottle

If parts are missing or damaged, please contact your dealer.

POWXG30010 EN

4 SYMBOLS

In this manual and/or on the machine the following symbols are used:

Keep hands, feet, hair and

clothing away from the

moving parts of the

machine.

Wear noise protection.

Direction of edger blade

rotation.

Wear eye protection.

Caution: Hot engine. Do

not touch a hot silencer or

cylinder. You may get

burned. These parts get

extremely hot from

operation. When turned off

they remain hot for a short

time.

Warning! Flying objects.

Beware of thrown objects hit by

cutting attachment.

Keep bystanders away.

Denotes risk of personal

injury or damage to the

tool.

Read the manual before use.

Wear gloves

Wearing of protective shoes

advised

5 GENERAL SAFETY RULES

WARNING: When using petrol tools, basic safety precautions, including the following, should

always be followed to reduce the risk of serious personal injury and/or damage to the unit.

Read all these instruction before operating this product and retain these instructions for future

reference.

5.1 Training

 Read the instructions carefully. Be familiar with the controls and the proper use of the

equipment;

 Never allow children or people unfamiliar with these instructions to use the lawn edge

cutter. Local regulations can restrict the age of the operator;

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to

other people or their property.

5.2 Preparation

 While mowing, always wear substantial footwear and long trousers. Do not operate the

equipment when barefoot or wearing open sandals;

 Thoroughly inspect the area where the equipment is to be used and remove all objects

which can be thrown by the machine;

WARNING! Petrol is highly flammable.

 store fuel in containers specifically designed for this purpose;

 refuel outdoors only and do not smoke while refuelling;

POWXG30010 EN

 add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol

while the engine is running or when the engine is hot;

 if petrol is spilled, do not attempt to start the engine but move the machine away from the

area of spillage and avoid creating any source of ignition until petrol vapours have

dissipated;

 replace all fuel tank and container caps securely;

 Replace faulty silencers;

 Before using, always visually inspect to see that the blades, blade bolts and cutter

assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to

preserve balance;

5.3 Operation

 This tool should only be used for lawn edging. Do not use it for any other purpose (e.g.

edging on hard ground).

 Do not operate the lawn edger barefoot or wearing open sandals. Always wear substantial

footwear and long trousers.

 Wear safety goggles or glasses and ear protectors when using this lawn edger. Use a

facemask if the work is dusty. Wear ear protection.

 Use this tool only in daylight or good artificial light.

 When edging on slopes:

 Always be sure of your footing on slopes.

 Don't operate lawn edger if the slope is excessively steep.

 Always walk, never run.

 Use extreme caution when reversing or pulling the lawn edger towards you.

 Make sure the blade has stopped before crossing surfaces other than grass and when

transporting the edger to and from the area to be edged.

 Never operate the edger with defective, missing or incorrectly fitted guards.

 Switch on the motor carefully according to instructions and with feet well away from the

blade(s).

 Do not tilt when switching on the motor, unless the edger has to be tilted for starting. Do

not tilt it more than absolutely necessary and tilt only the part which is away from the

operator.

 Do not start the lawn edger when a bystander is standing in front of the blade(s).

 Do not put your hands or feet near or under the rotating parts

 Switch off the lawn edger, make sure the blade has stopped in the following instances:

 Before cleaning blockages;

 Before checking, cleaning or working on the blade(s);

 After striking a foreign object: inspect the blade(s) for damage and make repairs before

restarting and operating the edger.

 If edger starts to vibrate abnormally (check immediately)

 Whenever you leave the lawn edger.

 Protect your tool. This edger is NOT WEATHERPROOF and should not be exposed to

direct sunlight, high ambient temperature and damp, wet or high humidity conditions.

WARNING! Cutting elements continue to rotate after the motor is switched

off.

5.4 Maintenance and storage

 Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition;

 never store the equipment with petrol in the tank inside a building where fumes can reach

an open flame or spark;

 Allow the engine to cool before storing in any enclosure;

POWXG30010 EN

 To reduce the fire hazard, keep the engine, silencer, battery compartment and petrol

storage area free of grass, leaves, or excessive grease;

 Replace worn or damaged parts for safety.

6 SAFETY WARNINGS GASOLINE

WARNING: Use extra care in handling fuels. They are flammable and the

vapours are explosive. The following points must be observed.

 Use only an approved container.

 Never remove the fuel cap or add fuel with the power source running. Allow engine

exhaust components to cool before refuelling.

 Do not smoke.

 Never refuel the machine indoors.

 Never store the machine or fuel containers inside, where is an open flame, such as a

water heater.

 If fuel is spilled, do not attempt to start the power source, but move the machine away

from the area of spillage before starting.

 Always replace and securely tighten the fuel cap after refuelling.

 If the tank is drained, this should be done outdoors.

7 STARTING AND STOPPING INSTRUCTIONS

7.1 Starting instructions

Note: before the engine start, check for loose parts or leakage, confirm the

blade is fixed appropriately and safely tightened.

1. Before starting, put the stop switch to the “I” position. After starting put the choke lever

back to the ‘open’ position.

2. Twist off the fuel tank cap and pour the fuel mixture in the fuel tank, do not overfill.

COLD STARTING: When cold starting, close the choke switch. With a warm

starting, there is no need to close the choke.

Note: DO NOT squeeze the throttle until step 7.

3. Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be

visible in the primer bulb (fig 2). If fuel cannot be seen in the bulb, press and release the

bulb until fuel is visible.

COLD STARTING: after starting, put the choke switch back to the open

position.

4. Pull the starter rope in a controlled motion until the unit starts.

5. Wait 60 seconds.

6. Tip the unit back so the blade does not touch the ground.

7. Squeeze the throttle control and allow the engine to warm up for 30 to 60 seconds. The

unit may be used during this time.

POWXG30010 EN

If the engine does not start, go back to step 3.

If the engine stops while squeezing the throttle, go back to step 4.

7.2 Stopping instructions

1. Release the throttle control and allow the engine to cool down by idling.

2. Press and hold the on/off switch in the OFF (0) position until the unit comes to a complete

stop (Fig. 1).

8 OPERATING INSTRUCTIONS

8.1 Holding the unit

Warning: Always wear eye, hearing, foot and body protection to reduce the

risk of injury when operating this unit.

Before operating the unit, stand in the operating position (fig. 3). Check for the following:

 The operator is wearing eye protection and proper clothing.

 Both hands are holding the handle bar firmly.

 The edger wheel is adjusted for proper cut depth as shown in Fig. 4 and edger positions

are as shown in Fig. 3.

8.2 Adjusting edger cutting depth

 Gently pull the depth adjustment lever away from the wheel bracket (Fig. 4).

 To raise the cutting blade, move the lever toward the front of the wheel bracket (Fig. 4).

Lowering the wheel decreases the cutting depth.

 To lower the cutting blade, move the lever toward the rear of the wheel bracket. Raising

the wheel increases the cutting depth.

8.3 Tips for best edging results

 After starting the engine, keep the unit tilted back so the blade does not touch the ground.

Move the unit to the desired location and slowly lower the blade into the ground.

 Do not force the edger. Edge the first time at a lesser depth, then do the area again with a

deeper setting.

 Walk the edger at a slow, even pace.

 Check the blade condition (Fig. 5). As it wears it becomes smaller, thus reducing the

cutting depth performance. Replace the blade when it no longer makes contact with the

ground.

9 OIL AND FUEL INFORMATION

Warning: Lack of lubrication voids engine warranty. Gasoline and oil must

be mixed at 40:1.

 The engine must use the mixture oil, the mixture ratio is 40:1.

 The gasoline should use the 90 octane or 93 octane unleaded gasoline.

 The oil should be two-stroke FC special mixing oil.

 Fill 585 ml gasoline (position 1) in the pot, and add two-stroke oil up to the 600 ml mark,

then shake it well.

 Don’t add too much fuel to the fuel tank, the fuel capacity should be 80 % of the fuel tank,

there should be some space left for gasoline expansion.

POWXG30010 EN

 The engine should be provided with fresh gasoline. Storage time of gasoline should not be

more than 30 days.

Note: Fuel which has been stored more than 30 days after mixing will result

in a carburettor blockage and the machine cannot be used normally.

 In the surrounding area of fuelling gasoline or fuel storage position any fire is strictly

forbidden.

 The engine should stop for 10 to 15 minutes after refuelling, then it may restart working.

 Poor quality gasoline and/or oil will damage the engine, oil seal, oil line and oil tank.

 Move the unit at least 10 m from the fuelling source and site before starting the engine.

1. Gasoline

2. Position 1 - 585 ml

3. Oil

4. Fuel mixing canister (empty bottle)

Warning: gasoline is extremely flammable. Ignited vapours may explode.

Always stop the engine and allow it to cool before filling the fuel tank. Do

not smoke while filling the tank. Keep sparks and open flames at a distance

from the area.

Warning: add fuel in a clean, well ventilated outdoor area. Wipe up any

spilled fuel immediately. Avoid creating a source of ignition for spilled fuel.

Do not start the engine until fuel vapours have completely dissipated.

9.1 Using fuel additives

The use of fuel additives will inhibit corrosion and minimize the formation of gum deposits.

Using a fuel additive can keep fuel from forming harmful deposits in the carburettor for up to

six months. Add 23 ml of fuel additive per gallon of fuel according to the instructions on the

fuel additive container. NEVER add fuel additives directly to the unit’s fuel tank.

Warning: remove fuel cap slowly to avoid injury from fuel spray. Never

operate the unit without the fuel cap securely in place.

POWXG30010 EN

Warning: when the engine stops, do not touch the muffler or spark plug

immediately in order to avoid any skin from burning.

9.2 Recommended petrol

Some standard petrols are enriched with oxygen-containing compounds such as alcohol or

ether to comply with regulations on clean air. The motor is designed to work well on any car

petrol, including these enriched petrols, on the condition that the above mixing ratios are

observed!

10 MAINTENANCE AND REPAIR INSTRUCTIONS

Warning: to avoid serious personal injury, always turn the unit off and allow

it to fully cool down before cleaning or maintaining it.

10.1 Maintenance schedule

Perform these required maintenance procedures at the frequency stated in the table. These

procedures should also be a part of any seasonal start.

Note: some maintenance procedures may require special tools or skills. If

you are unsure about these procedures take your unit to a qualified service

dealer.

Note: Maintenance, replacement, or repair of the emission control devices

and system should be performed by qualified service dealer.

After 25 hours: Clean up any dirt on the surface, clean the air filter; check the machine

whether there is fuel or air leakage and the compression systems works normal.

After 50 hours: Remove any carbon deposition from the spark plug or change the spark plug;

remove any carbon deposition from the muffler plate in the muffler.

After 100 hours: clean the cylinder exhaust hole, the top of piston, piston ring groove and

carbon deposition from the spark plug; clean the inside of the crankcase; check the ignition

system.

After 500 hours: clean and check the engine (except the crankshaft).

10.2 Blade replacement

1. Place the 8 mm Allen wrench on the blade nut (Fig. 6).

2. While holding the Allen wrench in place, loosen the nut with a 24 mm wrench by turning it

counter clockwise (Fig. 6).

3. Remove the nut and blade. Keep the nut for new blade installation.

4. Install the new blade and nut (Fig. 7).

Note: make sure the blade edges are facing the proper direction (Fig. 7).

The unit will not function correctly if the edger blade is installed backward.

5. While holding the Allen wrench in the spindle (arbor, shaft) hole, tighten the nut by turning

the wrench clockwise until tight (Fig. 6).

Note: make sure that the blade stays flat and centred against the output

shaft throughout installation.

POWXG30010 EN

10.3 Air filter maintenance

10.3.1 Cleaning the air filter

Clean and re-oil the air filter according to the maintenance schedule. It is an important item to

maintain. Failure to maintain the air filter properly can result in poor performance or can cause

permanent damage to the engine.

1. Unscrew the knob on the left side of the cover. Swing the cover out. Open the air filter

cover.

2. Remove the air filter.

3. Wash the filter in detergent and water. Rinse the filter thoroughly and allow it to dry.

4. Apply enough clean SAE 30 motor oil to lightly coat the filter.

5. Squeeze the filter to spread and remove excess oil.

6. Replace the filter

Note: operating the unit without the air filter, will VOID the warranty.

7. Make sure the back plate is correctly positioned.

8. Swing the air filter cover closed and tighten the knob.

10.4 Replacing the spark plug

Warning: do not sand blast, scrape or clean spark plug electrodes.

Remainders/particles left in the engine could damage the cylinder.

1. After using 25 hours, take off the spark plug, remove dirt and carbon deposition with a

steel brush. The spark plug gap should be 0.6-0.8 mm (see below).

2. Replace or clean the spark plug, confirm the surroundings of the spark plug is clean.

3. Do not clean spark plug with sand blast, but rather clean with a steel brush or in a carbon

remover solvent

4. Please use the recommended type when exchanging the spark plug.

5. When assembling the spark plug, turn it tight manually, then use a special spark plug

spanner to tighten.

Tightening torque: 15.3-22.4 Nm.

Note: it will damage the cylinder and piston if the fit is too tight

11 CLEANING AND STORAGE

11.1 Cleaning

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household

cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene,

can damage the plastic housing or handle. Wipe off any moisture with a soft cloth.

POWXG30010 EN

11.2 Storage

 Never store the unit with fuel in the tank where the fumes can reach an open flame or

spark.

 Allow the engine to fully cool down before storing

 Lock up the unit to prevent any unauthorized use or damage.

 Store the unit in a dry, well-ventilated area.

 Store the unit out of reach of children

11.3 Long term storage

1. Drain all gasoline from the gas tank into a container. Do not use gasoline that has been

stored for more than 30 days. Dispose of the old gasoline in accordance to federal, state

and local regulations.

2. Start the engine and allow it to run until it is running out of fuel and stops. This ensures

that all gasoline has been drained from the carburettor.

3. Allow the engine to fully cool down. Remove the spark plug and put 5 drops of high

quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall

the spark plug.

Note: remove the spark plug and drain all of the oil from the cylinder before

attempting to start the edger after storage.

4. Thoroughly clean the unit and inspect for any loose or damaged parts. Repair or replace

damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage.

12 TECHNICAL DATA

Model

POWXG30010

Rotation speed

9000 min

-1

Cylinder capacity

25.4

Engine power

0.75 kW

Max. cutting depth

45 mm

Clutch engagement speed

4200 min

-1

Idle speed

3000 min

-1

Engine type

PowerPlus 2-stroke engine

Fuel tank capacity

0.5 l

Low vibration system

Yes

Working depth

+22/+10/-4/-19/31mm

Heavy duty clutch

Yes

Fuel mixing ratio

40:1

Crank shaft

Double bearing

Spark plug type

Bosch

Handle type

Foldable

E10 fuel proof

Yes

POWXG30010 EN

13 NOISE

Noise emission values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

91 dB(A)

Acoustic power level LwA

106 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85

dB(A).

aw (Vibration):

7.1 m/s²

K = 1.5 m/s²

14 WARRANTY

 This product is warranted as provided by law for a 36 -month period effective from the

date of purchase by the first user.

 This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

 Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

 We also disclaim all liability for any bodily injury resulting from inappropriate use of the

tool.

 Repairs may only be carried out by an authorised customer service centre for Powerplus

tools.

 You can always obtain more information at the number 00 32 3 292 92 90.

 Any transportation costs shall always be borne by the customer, unless agreed otherwise

in writing.

 At the same time, no claim can be made on the warranty if the damage of the device is the

result of negligent maintenance or overload.

 Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike,

erroneus net voltage. This list is not exhaustive.

 Acceptance of claims under warranty can never lead to the prolongation of the warranty

period nor commencement of a new warranty period in case of a device replacement.

 Devices or parts which are replaced under the warranty therefore remain the property of

Varo NV.

 We reserve the right to reject a claim whenever the purchase cannot be verified or when it

is clear that the product has not been properly maintained. (Clean ventilation slots, carbon

brushes serviced regularly, etc.).

 Your purchase receipt must be kept as proof of date of purchase.

 Your appliance must be returned undismantled to your dealer in an acceptably clean state,

(in its original blow-moulded case if applicable to the unit), accompanied by proof of

purchase.

POWXG30010 EN

15 ENVIRONMENT

Should your appliance need replacement after extended use, do not discard it with the

household rubbish but dispose of it in an environmentally safe way.

Please dispose of used motor oil in a manner that is compatible with the environment. We

suggest you take it in a sealed container to your local service station for reclamation. Do not

throw it in the trash or pour it on the ground.

16 DECLARATION OF CONFORMITY

VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,

Product: LAWN EDGE CUTTER 25.4CC

Trade mark: POWERplus

Model: POWXG30010

is in conformity with the essential requirements and other relevant provisions of the applicable

European Directives, based on the application of European harmonized standards. Any

unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of signature):

2006/42/EC

2014/30/EU

2000/14/EC Annex V LwA 105dB(A) / 106dB(A)

European harmonized standards (including, if applicable, their amendments up to the date of

signature):

EN ISO 11789 : 1999

EN ISO 14982 : 2009

Keeper of the Technical Documentation: Philippe Vankerkhove, VARO – Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Philippe Vankerkhove

Regulatory Affairs – Compliance Manager

08/05/17

Powerplus POWXG30010 Owner's manual

Powerplus POWXG30010 Owner's manual

Powerplus POWXG30010 Owner's manual

Related papers

Other documents