Aerco Benchmark BMK 3000 User manual

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 1 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

GF-206

OPERATION, SERVICE and MAINTENANCE GUIDE

Natural Gas, Propane Gas, or Dual Fuel Fired Modulating, Condensing Boilers

Latest Update: 11/29/2017

Natural Gas:

• BMK 750

• BMK 1000

• BMK 1500

• BMK 2000

• BMK 2500

• BMK 3000

APPLIES TO MODELS:

Applies to Serial Numbers:

G-17-2400 and above.

Dual-Fuel (NG/P):

• BMK 1500DF

• BMK 2000DF

• BMK 2500DF

• BMK 3000DF

USER MANUAL

(2 of 2)

SEE ALSO: Benchmark

Installation and Startup Guide,

OMM-0121 (GF-205)

750, 1000, 1500, 2000, 2500, and 3000 MBH Boilers

Propane:

• BMK 750P

• BMK 1000P

• BMK 1500P

•

BMK 2000P

• BMK 2500P

• BMK 3000P

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

CONTENTS

Page 2 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

TABLE OF CONTENTS

FOREWORD ...................................................................................................... 5

SECTION 1: SAFETY PRECAUTIONS ................................................................... 9

1.1 WARNINGS & CAUTIONS ..................................................................................................................... 9

1.2 EMERGENCY SHUTDOWN ................................................................................................................. 10

1.3 PROLONGED SHUTDOWN ................................................................................................................. 10

1.4 IMPORTANT – FOR MASSACHUSETTS INSTALLATIONS ............................................................... 11

SECTION 2: OPERATION ................................................................................. 13

2.1 INTRODUCTION ................................................................................................................................... 13

2.2 C-MORE CONTROLLER DESCRIPTION ............................................................................................ 14

2.3 C-MORE CONTROLLER MENUS ........................................................................................................ 17

2.3.1 Menu Navigation and Processing Procedure .................................................................................................. 17

2.4 OPERATING MENU ............................................................................................................................. 19

2.5 SETUP MENU ....................................................................................................................................... 20

2.6 CONFIGURATION MENU .................................................................................................................... 21

2.7 TUNING MENU ..................................................................................................................................... 23

2.8 COMBUSTION CAL MENU .................................................................................................................. 23

2.8.1 BMK 750/1000 COMBUSTION CAL Menu ....................................................................................................... 23

2.8.2 BMK 1500/2000 COMBUSTION CAL Menus ................................................................................................... 24

2.8.3 BMK 2500/3000 COMBUSTION CAL Menus ................................................................................................... 25

2.9 BST (BOILER SEQUENCING TECHNOLOGY) MENU ....................................................................... 26

2.10 CALIBRATION MENU......................................................................................................................... 29

SECTION 3: MODES OF OPERATION ............................................................... 31

3.1 INTRODUCTION ................................................................................................................................... 31

3.2 INDOOR/OUTDOOR RESET MODE ................................................................................................... 31

3.2.1 Reset Ratio ...................................................................................................................................................... 31

3.2.2 Building Reference Temperature .................................................................................................................... 31

3.2.3 Outdoor Air Temperature Sensor Installation ................................................................................................ 31

3.2.4 Indoor/Outdoor Startup ................................................................................................................................. 32

3.3 CONSTANT SETPOINT MODE ........................................................................................................... 32

3.3.1 Setting the Setpoint ........................................................................................................................................ 33

3.4 REMOTE SETPOINT MODES ............................................................................................................. 33

3.4.1 Remote Setpoint Field Wiring ......................................................................................................................... 34

3.4.2 Remote Setpoint Startup ................................................................................................................................ 34

3.5 DIRECT DRIVE MODES....................................................................................................................... 34

3.5.1 Direct Drive Field Wiring ................................................................................................................................. 35

3.5.2 Direct Drive Startup ........................................................................................................................................ 35

3.6 AERCO CONTROL SYSTEM (ACS) .................................................................................................... 36

3.6.1 ACS External Field Wiring................................................................................................................................ 36

3.6.2 ACS Setup and Startup .................................................................................................................................... 36

3.7 COMBINATION CONTROL SYSTEM (CCS) ....................................................................................... 37

3.7.1 Combination Control System Field Wiring ...................................................................................................... 38

3.7.2 Combination Control System Setup and Startup ............................................................................................ 38

SECTION 4: MAINTENANCE ............................................................................ 39

4.1 MAINTENANCE SCHEDULE ............................................................................................................... 39

4.2 IGNITER-INJECTOR ............................................................................................................................ 40

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

CONTENTS

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 3 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

4.3 FLAME DETECTOR ............................................................................................................................. 45

4.4 O

2

SENSOR .......................................................................................................................................... 45

4.5 SAFETY DEVICE TESTING ................................................................................................................. 46

4.6 BURNER INSPECTION ........................................................................................................................ 46

4.6.1 BMK 750/1000 BURNER INSPECTION ............................................................................................................. 47

4.6.2 BMK 1500 – 3000 BURNER INSPECTION ......................................................................................................... 49

4.7 CONDENSATE DRAIN TRAP .............................................................................................................. 53

4.8 AIR FILTER CLEANING AND REPLACEMENT .................................................................................. 54

4.9 WATER CUTOFF (LWCO) CAPACITOR INTEGRITY TEST ............................................................... 55

4.9.1 Low Water Cutoff (LWCO) - Capacitor Electrical Short Test ........................................................................... 56

4.9.2 Low Water Cutoff (LWCO) - Standard C-More Test ........................................................................................ 57

4.10 SHUTTING BOILER DOWN FOR EXTENDED PERIOD ................................................................... 57

4.11 PLACING THE BOILER BACK IN SERVICE AFTER A PROLONGED SHUTDOWN ....................... 57

4.12 SPARK MONITOR (AC CURRENT TRANSDUCER) ......................................................................... 58

SECTION 5: TROUBLESHOOTING GUIDE ......................................................... 59

5.1 INTRODUCTION ................................................................................................................................... 59

5.2 ADDITIONAL FAULTS WITHOUT SPECIFIC FAULT MESSAGES .................................................... 71

APPENDIX A: BOILER MENU ITEM DESCRIPTIONS ............................................. 73

TABLE A-1: OPERATING MENU ITEM DESCRIPTIONS ......................................................................... 73

TABLE A-2: SETUP MENU ITEM DESCRIPTIONS ................................................................................... 75

TABLE A-3: CONFIGURATION MENU ITEM DESCRIPTIONS ................................................................ 76

TABLE A-4: TUNING MENU ITEM DESCRIPTIONS ................................................................................. 79

TABLE A-5: COMBUSTION CALIBRATION MENU ITEM DESCRIPTIONS ............................................. 80

TABLE A-6: CALIBRATION MENU ITEM DESCRIPTIONS ....................................................................... 81

APPENDIX B: STARTUP, STATUS, & FAULT MESSAGES ...................................... 85

TABLE B-1: STARTUP AND STATUS MESSAGES .................................................................................. 85

TABLE B-2: FAULT MESSAGES ............................................................................................................... 86

APPENDIX C: SENSOR RESISTANCE/VOLTAGE CHART ........................................ 89

APPENDIX D: RECOMMENDED PERIODIC TESTING ............................................ 91

APPENDIX E: INDOOR/OUTDOOR RESET RATIO CHARTS .................................. 93

APPENDIX F: BENCHMARK 750/1000 PART LIST ............................................... 97

APPENDIX G: BENCHMARK 1500/2000 PART LIST ........................................... 107

APPENDIX H: BENCHMARK 2500/3000 PART LIST ........................................... 123

APPENDIX I: WIRING DIAGRAMS ................................................................... 145

APPENDIX J: C-MORE CONTROLLER VIEWS .................................................... 161

APPENDIX K: RECOMMENDED SPARES ........................................................... 163

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

CONTENTS

Page 4 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

(This page intentionally blank)

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

FORWARD

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 5 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

FOREWORD

The AERCO Benchmark (BMK) 750, 1000, 1500, 2000, 2500, and 3000 natural gas and

propane fueled boilers are modulating and condensing units. They represent a true industry

advance that meets the needs of today's energy and environmental concerns. Designed for

application in any closed loop hydronic system, the Benchmark's modulating capability relates

energy input directly to fluctuating system loads. These BMK models provide extremely high

efficiency operation and are ideally suited for modern low temperature, as well as, conventional

heating systems.

The Benchmark models operate within the following input and output ranges:

IMPORTANT!

Unless otherwise specified, all measurements apply to both natural gas and propane models.

Benchmark Boiler Intake and Output Ranges

MODEL

INPUT RANGE (BTU/HR.) OUTPUT RANGE (BTU/HR.)

MINIMUM MAXIMUM MINIMUM MAXIMUM

BMK 750 50,000 (14.6 kW) 750,000 (220 kW) 47,750 (14 kW) 716,250 (210 kW)

BMK 1000 50,000 (14.6 kW) 1,000,000 (293 kW) 48,300 (14.15 kW) 968,000 (284 kW)

BMK 1500 75,000 (22 kW) 1,500,000 (440 kW) 64,500 (18.9 kW) 1,395,000 (409 kW)

BMK 2000 100,000 (29.3 kW) 2,000,000 (586 kW) 86,000 (25.2 kW) 1,860,000 (545 kW)

BMK 2500 167,000 (48.9 kW) 2,500,000 (732 kW) 144,000 (42.2 kW) 2,395,000 (702 kW)

BMK 3000 200,000 (58.6 kW) 3,000,000 (879 kW) 174,000 (51.0 kW) 2,874,000 (842 kW)

The output of the boiler is a function of the unit’s firing rate (valve position) and return water

temperature.

When installed and operated in accordance with this Instruction Manual, these boilers comply

with the NO

x

emission standards outlined in: South Coast Air Quality Management District

(SCAQMD), Rule 1146.2. In addition, the BMK 750 & 1000 comply with the Bay Area Air

Quality Management District regulation 9, Rule 7.

Whether used in singular or modular arrangements, the BMK boilers offer the maximum venting

flexibility with minimum installation space requirements. These boilers are Category II and IV,

positive pressure appliances. Single and/or multiple breeched units are capable of operation in

the following vent configurations:

• Room Combustion Air:

o Vertical Discharge

o Horizontal Discharge

• Ducted Combustion Air:

o Vertical Discharge

o Horizontal Discharge

These boilers are capable of being vented utilizing Polypropylene and AL29-4C vent systems.

The Benchmark's advanced electronics are available in several selectable modes of operation

offering the most efficient operating methods and energy management system integration.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

FORWARD

Page 6 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

AERCO Technical Terminology Meanings

TERMINOLOGY MEANING

A (Amp)

Ampere

ACS AERCO Control System, AERCO’s boiler management systems

ADDR Address

AGND Analog Ground

ALRM Alarm

ANSI American National Standards Institute,

ASME American Society of Mechanical Engineers

AUX Auxiliary

BAS

Building Automation System, often used interchangeably with EMS

(see below)

Baud Rate

Symbol rate, or simply the number of distinct symbol changes

(signaling events) transmitted per second. It is not equal to bits per

second, unless each symbol is 1 bit long.

BMK (Benchmark) AERCO’s Benchmark series boilers

BMS or BMS II AERCO Boiler Management Systems

BLDG (Bldg) Building

BST AERCO on-board Boiler Sequencing Technology

BTU

British Thermal Unit. A unit of energy approximately equal to the

heat required to raise 1 pound (0.45 kg) of water 1°F (0.55 °C)

BTU/HR

BTUs per Hour

(1 BTU/hr = 0.29 W)

CCP

Combination Control Panel

CCS

Combination Control System

C-More Controller

A control

system developed by AERCO and currently used in all

Benchmark, Innovation and KC1000 Series product lines.

CFH Cubic Feet per Hour (1 CFH = 0.028 m

3

/hr)

CO Carbon Monoxide

COMM (Comm) Communication

Cal. Calibration

CNTL Control

CPU Central Processing Unit

DBB

Double Block and Bleed, a gas trains containing 2 Safety Shutoff

Valves (SSOVs) and a solenoid operated vent valve.

DIP Dual In-Line Package, a type of switch

ECU Electronic Control Unit (O

2

sensor)

EMS Energy Management System; often used interchangeably with BAS

FM Factory Mutual. Used to define boiler gas trains.

GF-xxxx Gas Fired (an AERCO document numbering system)

GND Ground

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

FORWARD

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 7 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

AERCO Technical Terminology Meanings

TERMINOLOGY MEANING

HDR

Header

Hex Hexadecimal Number (0 – 9, A – F)

HP Horse Power

HX Heat Exchanger

Hz Hertz (Cycles Per Second)

I.D. Inside Diameter

IGN Ignition

IGST Board Ignition/Stepper Board, contained in the C-More Controller

INTLK (INTL’K) Interlock

I/O Input/Output

I/O Box

Input/Output (I/O) Box currently used on Benchmark, Innovation and

KC1000 Series products

IP Internet Protocol

ISO International Organization for Standardization

Lbs. Pounds (1 lb = 0.45 kg)

LED Light Emitting Diode

LN Low Nitrogen Oxide

MA (mA) Milliampere (1 thousand

th

of an ampere)

MAX (Max) Maximum

MBH

1000 BTUs per Hour

MIN (Min) Minimum

Modbus®

A serial, half-

duplex data transmission protocol developed by AEG

Modicon

NC (N.C.) Normally Closed

NO (N.O.) Normally Open

NO

x

Nitrogen Oxide

NPT National Pipe Thread

O

2

Oxygen

O.D. Outside Diameter

OMM & O&M Operation and Maintenance Manual

onAER

AERCO’s on-line remote monitoring system

PCB Printed Circuit Board

PMC Board Primary Micro-Controller (PMC) board, contained in the C-More

P/N Part Number

POC

Proof of Closure

PPM

Parts per Million

PSI

Pounds per Square Inch (1 PSI = 6.89 kPa)

PTP

Point-to-Point (usually over RS232 networks)

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

FORWARD

Page 8 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

AERCO Technical Terminology Meanings

TERMINOLOGY MEANING

P&T

Pressure and Temperature

ProtoNode Hardware interface between BAS and a boiler or water heater

PVC Poly Vinyl Chloride, a common synthetic plastic

PWM Pulse Width Modulation

REF (Ref) Reference

RES. Resistive

RS232

(or EIA-232)

A standard for serial, full-

duplex (FDX) transmission of data based

on the RS232 Standard

RS422

(or EIA-422)

A standard for serial, full-

duplex (FDX) transmission of data based

on the RS422 Standard

RS485

(or EIA-485)

A standard for serial, half-duplex (HDX) transmission of data based

on the RS485 Standard

RTN (Rtn) Return

SETPT (Setpt) Setpoint Temperature

SHLD (Shld) Shield

SPDT Single Pole Double Throw, a type of switch

SSOV Safety Shut Off Valve

TEMP (Temp) Temperature

Terminating Resistor

A resistor placed at each end of a daisy-chain or multi-drop network

in order to prevent reflections that may cause invalid

data in the

communication

Tip-N-Tell A device that indicates if a package was tipped during shipping

UL A business that tests and validates products

VAC Volts, Alternating Current

VDC Volts, Direct Current

VFD Vacuum Fluorescent Display, also Variable Frequency Drive

W Watt

W.C. Water Column, a unit of pressure (1 W.C. = 249 Pa)

µA Micro amp (1 million

th

of an ampere)

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 1: SAFETY PRECAUTIONS

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 9 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

SECTION 1: SAFETY PRECAUTIONS

1.1 WARNINGS & CAUTIONS

Installers and operating personnel MUST, at all times, observe all safety regulations. The

following warnings and cautions are general and must be given the same attention as specific

precautions included in these instructions. In addition to all the requirements included in this

AERCO Instruction Manual, the installation of units MUST conform with local building codes, or,

in the absence of local codes, ANSI Z223.1 (National Fuel Gas Code Publication No. NFPA-54)

for gas-fired boilers and ANSI/NFPASB for LP gas-fired boilers. Where applicable, the

equipment shall be installed in accordance with the current Installation Code for Gas Burning

Appliances and Equipment, CSA B149.1, and applicable Provincial regulations for the class;

which should be carefully followed in all cases. Authorities having jurisdiction should be

consulted before installations are made.

See section 1.4 for important information regarding installation of units within the

Commonwealth of Massachusetts.

IMPORTANT!

This Instruction Manual is an integral part of the product and must be maintained in legible

condition. It must be given to the user by the installer and kept in a safe place for future

reference.

WARNING!

• Do not use matches, candles, flames, or other sources of ignition to check for gas leaks.

• Fluids under pressure may cause injury to personnel or damage to equipment when

released. Be sure to shut off all incoming and outgoing water shutoff valves. Carefully

decrease all trapped pressures to zero before performing maintenance.

• Before attempting to perform any maintenance on the unit, shut off all gas and electrical

inputs to the unit.

• The exhaust vent pipe of the unit operates under a positive pressure and therefore must be

completely sealed to prevent leakage of combustion products into living spaces.

• Electrical voltages up to 120 VAC may be used in this equipment. Therefore the cover on

the unit’s power box (located behind the front panel door) must be installed at all times,

except during maintenance and servicing.

• A three-pole switch must be installed on the electrical supply line of the unit. The switch

must be installed in an easily accessible position to quickly and safely disconnect electrical

service. Do not affix switch to unit sheet metal enclosures.

CAUTION!

• Many soaps used for gas pipe leak testing are corrosive to metals. The piping must be

rinsed thoroughly with clean water after leak checks have been completed.

• DO NOT use this boiler if any part has been under water. Call a qualified service technician

to inspect and replace any part that has been under water.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 1: SAFETY PRECAUTIONS

Page 10 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

1.2 EMERGENCY SHUTDOWN

If overheating occurs or the gas supply fails to shut off, close the manual gas shutoff valve

(Figure 1-1) located external to the unit.

NOTE:

The Installer must identify and indicate the location of the emergency shutdown manual gas

valve to operating personnel.

Figure 1-1: Manual Gas Shutoff Valve

1.3 PROLONGED SHUTDOWN

After prolonged shutdown, it is recommended that the startup procedures and safety device test

procedures, described in Section 4 and 5, respectively of the Benchmark 750 – 3000 Installation

and Startup Guide, OMM-0121 (GF-205) be performed to verify all system-operating

parameters. If there is an emergency, turn off the electrical power supply to the AERCO boiler

and close the manual gas valve located upstream the unit. The installer must identify the

emergency shut-off device.

VALVE

OPEN

VALVE

CLOSED

MANUAL GAS SHUT-OFF VALVE

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 1: SAFETY PRECAUTIONS

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 11 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

1.4 IMPORTANT – FOR MASSACHUSETTS INSTALLATIONS

Requirements For Massachusetts Installations

Boiler Installations within the Commonwealth of Massachusetts must conform to the

following requirements:

• Boiler must be installed by a plumber or a gas fitter who is licensed within the

Commonwealth of Massachusetts.

• Prior to unit operation, the complete gas train and all connections must be leak

tested using a non-corrosive soap.

• The vent termination must be located a minimum of 4 feet above grade level. If

side-wall venting is used, the installation must conform to the following

requirements extracted from 248 CMR 5.08 (2):

(a) For al

l side wall horizontally vented gas fueled equipment installed in every dwelling,

building or structure used in whole or in part for residential purposes, including those owned or

operated by the Commonwealth and where the side wall exhaust vent termination is less than

seven (7) feet above finished grade in the area of the venting, including but not limited to decks

and porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS: At the time of installation of the

side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall

observe that a hard wired carbon monoxide detector with an alarm and battery back-up is

installed on the floor level where the gas equipment is to be installed. In addition, the

installing plumber or gasfitter shall observe that a battery operated or hard wired carbon

monoxide detector with an alarm is installed on each additional level of the dwelling,

building or structure served by the side wall horizontal vented gas fueled equipment. It shall

be the responsibility of the property owner to secure the services of qualified licensed

professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a

crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery

back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of

completion of installation, the owner shall have a period of thirty (30) days to comply with

the above requirements; provided, however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS:

Each carbon monoxide detector as

required in

accordance with the above provisions shall comply with NFPA 720 and be

ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE: A metal or plastic identification plate shall be permanently mounted to the

exterior of the building at a minimum height of eight (8) feet above grade directly in line

with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS". (Continued)

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 1: SAFETY PRECAUTIONS

Page 12 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

Requirements For Massachusetts Installations

4. INSPECTION: The state or local gas inspector of the side wall horizontally vented gas

fueled equipment shall not approve the installation unless, upon inspection, the inspector

observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Section 10 entitled "Equipment Not Required To Be Vented" in

the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a

room or structure separate from the dwelling, building or structure used in whole or in

part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When

the manufacturer of Product Approved side wall horizontally vented gas equipment provides a

venting system design or venting system components with the equipment, the instructions

provided by the manufacturer for installation of the equipment and the venting system shall

include:

1. Detailed instructions for the installation of the venting system design or the venting

system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED.

When the manufacturer of a Product Approved side wall horizontally vented gas fueled

equipment does not provide the parts for venting the flue gases, but identifies "special venting

systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance

or equipment installation instructions; and

2. The "special venting sy

stems" shall be Product Approved by the Board, and the

instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented

gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all

venting design instructions shall remain with the appliance or equipment at the completion of

the installation.

……………….[End of Extracted Information From 248 CMR 5.08 (2)]…………………

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 13 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

SECTION 2: OPERATION

2.1 INTRODUCTION

The information in this section provides a guide to the operation of the Benchmark Boiler using

the C-More Controller mounted on the front of the unit. It is imperative that the initial startup of

this unit be performed by factory trained personnel. Operation prior to initial startup by factory

trained personnel may void the equipment warranty. In addition, the following WARNINGS and

CAUTIONS must be observed at all times.

WARNING!

• ELECTRICAL VOLTAGES IN THIS SYSTEM INCLUDE 120 VAC (BMK 750 – 2000) and

208 or 460 VAC (BMK 2500/3000) and 24 volts AC. It must be serviced only by factory

certified service technicians.

• DO NOT ATTEMPT TO DRY FIRE THE UNIT. Starting the unit without a full water level

can seriously damage the unit and may result in injury to personnel or property damage.

This situation will void any warranty.

CAUTION!

All of the installation procedures in the Benchmark 750 – 3000 Installation and Startup Guide,

OMM-0121 (GF-205) must be completed before attempting to start the unit.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

Page 14 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

2.2 C-MORE CONTROLLER DESCRIPTION

All Benchmark boilers utilize the C-More Controller shown in Figure 2-1. This panel contains all

of the controls, indicators and displays necessary to operate, adjust and troubleshoot the boiler.

These operating controls, indicators and displays are listed and described in Table 2-1.

Additional information on these items is provided in the individual operating procedures and

menu descriptions provided in this section.

Figure 2-1: C-More Controller Front View

1

12

11

10

9

8

7

5

4

3

6

2

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 15 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

TABLE 2-1: Controls, Indicators, And Displays (ref. Figure 2-1)

ITEM

CONTROL, INDICATOR

or DISPLAY

FUNCTION

1

LED STATUS INDICATORS

Four Status LEDs indicate the current operating status as follows:

COMM =

Lights when RS232 communication is occurring – see Item 4.

MANUAL =

Lights when the valve position (fire rate) is being controlled using the front

panel keypad. This mode of operation is for service technician use only.

REMOTE =

Lights when the unit is being controlled by an external signal from an Energy

Management System.

DEMAND =

Lights when there is a demand for heat.

2

OUTLET

TEMPERATURE

Display

3–Digit, 7–

Segment LED display continuously displays the outlet

water temperature. The °F or °C LED next to the display lights to

indicate whether the displayed temperature is in degrees Fahrenheit

or degrees Celsius. The °F or °C

blinks when operating in the

DEADBAND mode.

On a BST Manager, display flashes & shows header temperature.

3

VFD Display

Vacuum Fluorescent Display (VFD) consists of 2 lines each capable

of displaying up to 16 alphanumeric characters. The information

displayed includes:

• Startup Messages

• Fault Messages

• Operating Status Messages

• Menu Selection

• BST Messages

4

RS232 Port

This port is used only by factory-

trained personnel to monitor

onAER

communications, in combination with the RS232 Adaptor

Cable (P/N 124675).

5

FAULT Indicator

Red FAULT

LED indicator lights when a boiler alarm condition

occurs. An alarm message will appear in the VFD.

6

CLEAR Key

Turns off the FAULT indicator and clears the alarm message if the

alarm is no longer valid. Lockout type alarms will be latched and

cannot

be cleared by simply pressing this key. Troubleshooting

may be required to clear these types of alarms.

7

READY Indicator

Lights when ON/OFF switch is set to ON and when all Pre-Purge

conditions have been satisfied.

8

ON/OFF switch

Enables and disables boiler operation.

9

LOW WATER

LEVEL

TEST/RESET

switches

• Allows operator to test operation of the water level monitor.

• Pressing TEST

opens the water level probe circuit and

simulates a Low Water Level alarm.

• Pressing RESET resets the water level monitor circuit.

• Pressing the CLEAR key (item 6) resets the display.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

Page 16 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

TABLE 2-1: Controls, Indicators, And Displays (ref. Figure 2-1)

ITEM

CONTROL, INDICATOR

or DISPLAY

FUNCTION

10

MENU KEYPAD

Six (6) keys which provide the following functions for the C-More Controller menus:

MENU

Steps through the main menu categories shown in Figure 2-2. The menu

categories wrap around in the order shown.

BACK

Allows you to go back to the previous menu level without changing any

information. Continuously pressing this key will bring you back to the

default status display in the VFD. Also, this key allows you to go back to

the top of a main menu category.

▲

(UP)

Arrow

When in one of the main menu categories (Figure 2-2), pressing the ▲

arrow key will select the displayed menu category. If the CHANGE key was

pressed and the menu item is flashing, pressing the ▲

arrow key will

increment the selected setting.

▼

(DOWN)

Arrow

When in one of the main menu categories (Figure 2-2), pressing this key

will select the displayed menu category. If the CHANGE key was pressed

and the menu item is flashing, pressing the ▼ arrow key will decrement the

selected setting.

CHANGE

Permits a setting to be changed (edited). When the CHANGE

key is

pressed, the displayed menu item will begin to flash. Pressing the ▲ or ▼

arrow key when the item is flashing will increment or decr

ement the

displayed setting.

ENTER

Saves the modified menu settings in memory. The display will stop

flashing.

11

AUTO/MAN switch

This switch toggles the boiler between the AUTOMATIC and

MANUAL modes of operation. When in the MANUAL (MAN) mode,

the front panel controls are enabled and the MANUAL status LED

lights. Manual operation is for service only.

When in the AUTOMATIC (AUTO) mode, the MANUAL status LED

will be off and the front panel controls disabled.

12

VALVE POSITION

Bargraph

20 segment red LED bargraph continuously shows the Air/Fuel

Valve position in 5% increments from 0 to 100%

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 17 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

2.3 C-MORE CONTROLLER MENUS

The C-More Controller incorporates an extensive menu structure which permits the operator to

set up, and configure the unit. The menu structure consists of five major menu categories which

are applicable to this manual. These categories are shown in Figure 2-2. Each of the menus

shown, contain options which permit operating parameters to be viewed or changed. The

menus are protected by password levels to prevent unauthorized use.

Prior to entering the correct password, the options contained in the Operation, Setup,

Configuration and Tuning menu categories can be viewed. However, with the exception of

Internal Setpoint Temperature (Configuration menu), none of the viewable menu options can be

changed.

Once the valid level 1 password (159) is entered, the options listed in the Setup, Configuration

and Tuning menus can be viewed and changed, if desired. The Combustion Cal menu is

protected by the level 2 password (6817), which is used in initial startup (see Section 4: Initial

Startup of the Benchmark 750 – 3000 Installation and Startup Guide, OMM-0121 (GF-205)), to

perform combustion calibration prior to service use.

2.3.1 Menu Navigation and Processing Procedure

Accessing and initiating each menu and option is accomplished using the menu keys shown in

Figure 2-1. Therefore, it is imperative that you be thoroughly familiar with the following basic

steps before attempting to perform specific menu procedures:

Menu Navigation and Processing Procedure Instructions

1. The C-More Controller will normally be in the Operating menu and the VFD will display the

current unit status. Pressing the ▲ or ▼ arrow key will display the other available data

items in the Operating menu.

2. Press the MENU key. The display will show the Setup

menu, which is the next menu

category shown in Figure 2-2. This menu contains the Password option which must be

entered if other menu options will be changed.

3. Continue pressing the MENU key until the desired menu is displayed.

4. With the desired menu displayed, press the ▲ or ▼ arrow key. The first option

in the

selected menu will be displayed.

5.

Continue to press the ▲ or ▼ arrow key until the desired menu option is displayed.

Pressing the ▲ arrow key will display the available menu options in the Top-Down

sequence. Pressing the ▼ arrow key will display the options in the Bottom-Up sequence.

The menu options will wrap-around after the first or last available option is reached.

6. To change the value or setting of a displayed menu option, press the CHANGE key. The

displayed option will begin to flash. Press the ▲ or ▼ arrow key to scroll through the

available menu option choices for the option to be changed. The menu option choices do

not wrap around.

7. To select and store a changed menu item, press the ENTER key.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

Page 18 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

* Only if BST is enabled. BST is described in detail in Section 6 of the Benchmark 750 – 3000

Installation and Startup Guide, OMM-0121 (GF-205).

Figure 2-2: Menu Structure

NOTE:

The following sections provide brief descriptions of the options contained in each menu.

Refer to Appendix A for detailed descriptions of each menu option. Refer to Appendix B

for a list and descriptions of startup, status and error messages.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

OMM-0122_0C AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 19 of 164

GF-206 Ph.: 800-526-0288 11/29/2017

2.4 OPERATING Menu

The Operating menu displays a number of key operating parameters for the unit. All items in this

menu except O2 Monitor (item 15) are “Read-Only” and cannot be changed. This menu can be

accessed without entering a password.

A full description of each item appears in Appendix A-1.

TABLE 2-2: OPERATING Menu

MENU ITEM DISPLAY

AVAILABLE CHOICES OR LIMIT

Appears Only If

Enabled in:

Minimum

Maximum

1

Active Setpoint

40°F (4.4°C) 240°F (116°C)

2

Outlet Temp

30°F (-1.1°C) 240°F (116°C)

Configuration Menu

3

Inlet Temp

30°F (-1.1°C) 240°F (116°C)

4

Air Temp

-70°F (-56.7°C) 245°F (118°C)

5

Outdoor Temp

-70°F (-56.7°C) 130°F (54.4°C)

Configuration Menu

6

Valve Position In 0% 100%

7

Valve Position Out 0% 100% Configuration Menu

8

FFWD Temp

30°F (-1.1°C)

240°F (115.6°C)

9

Exhaust Temp Displays current exhaust temperature

10

Flame Strength 0% 100%

11

Min Flame Str Not Used

12

O2 Monitor Enable Disable O2 Monitor = Enabled

13

Oxygen Level 0% 21%

14

Ignition Time 0.00 10.00

15

SSOV Time to OPN 0.00 10.00

16

Spark Current

0 amps 2.5 amps

17

Run Cycles 0 999,999,999

18

Run Hours 0 999,999,999

19

Fault Log 0 19

An additional parameter associated with the Operating menu, (Min = 0, Max = 100) does not

appear in this menu, but can be displayed by pushing the Auto/Man button on the C-More

Controller’s front face.

Benchmark 750-3000 Boiler Operation, Service & Maintenance Guide

SECTION 2: OPERATION

Page 20 of 164 AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 OMM-0122_0C

11/29/2017 Ph.: 800-526-0288 GF-206

2.5 SETUP Menu

The Setup menu permits the operator to enter the unit password (159) which is required to

change the menu options. To prevent unauthorized use, the password will time-out after 1 hour.

Therefore, the correct password must be reentered when required. In addition to permitting

password entries, the Setup menu is also used to enter date and time, and units of temperature

measurements. A view-only software version display is also provided to indicate the current C-

More Controller software version.

A full description of each item appears in Appendix A-2.

TABLE 2-3: SETUP Menu

MENU ITEM DISPLAY

AVAILABLE CHOICES OR LIMIT

DEFAULT

Minimum Maximum

1

Password 0 9999 0

2

Language

English

3

Time

12:00 am

11:59 pm

12:00

4

Date 01/01/00 12/31/99 01/01/00

5

Unit of Temp

Fahrenheit or Celsius

Fahrenheit

6

Comm Address 0 127 0

7

Baud Rate

2400, 4800, 9600, 19.2K

9600

8

onAER Mode Ethernet or SD Card Ethernet

9

Min Upload Timer 0 9,999 Sec 0

10

Unit Alpha E, G, H, R, N or A A

11

Unit Year 0 99 0

12

Unit Serial # 0 9999 0

13

Software Ver 0.00 Ver 9.99

Current software

version

Page is loading ...

Aerco Benchmark BMK 3000 User manual

Aerco Benchmark BMK 3000 User manual

Related papers

Other documents