Samsung LW29A13W User manual

LCD TV

LW29A13W

LW40A13W

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

PC DISPLAY

PICTURE IN PICTURE (PIP)

PICTURE BY PICTURE (PBP)

TELETEXT

apollo_en 12/23/02 5:24 PM Page 1

English-2

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Samsung

Electronics Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or

use of this material.

The

Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.;

Microsoft, Windows

®

and Windows

®

NT are registered trademark of Microsoft

Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics

Standard Association. All other product names mentioned herein may be the trademarks

or registered trademarks of their respective owners.

Plug and Play

The adoption of the new VESA

®

Plug and Play solution eliminates complicated and time

consuming setup. It allows you to install your set in a Plug and Play compatible system

without the usual hassles and confusion. Your computer system can easily identify and

configure itself for use with your set.

Your set automatically tells the computer system its Extended Display Identification Data

(EDID) using Display Data Channel (DDC) protocols so the computer system can

automatically configure itself to use your set. If your PC system needs a monitor driver,

install monitor driver contained on the accompanied CD according to the operating

system your computer uses. For more information, refer to the driver installation

instructions included with your CD package.

PowerSaver

This set is EPA ENERGY STAR

®

compliant and NUTEK compliant when used with a

computer equipped with VESA DPMS functionality. For energy conservation, turn your set

Off when you are not using it or when leaving it unattended for long periods.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC),

(92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the

Commission of the European Community. Compliance with these directives implies

conformity to the following European Norms:

■ EN55022:1998 – Radio Frequency Interference

■ EN55024:1998 – Electromagnetic Immunity

■ EN61000-3-2:1995 + A1 + A2 – Power Line Harmonics

■ EN61000-3-3:1995 – Voltage Fluctuations

■ EN60950 – Product Safety.

apollo_en 12/23/02 5:24 PM Page 2

English-3

Caution

CAUTION:

TO PREVENT ELECTRICAL SHOCK,

DO NOT REMOVE REAR COVER, NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION

The lightning flash and arrow head

within the triangle is a warning

sign alerting you of “dangerous

voltage” inside the product.

The exclamation point within the

triangle is a warning sign alerting

you of important instructions

accompanying the product.

WARNING:TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

☛

The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.

Safety Instructions

These illustrations represent precautions concerning your set.

5°

10%

H

40°

75%

Do NOT expose your set to

extreme temperature or

humidity conditions.

Do NOT expose your set to

direct sunlight.

Do NOT expose your set to

any liquids.

If your set is broken, do not try

to repair it yourself. Contact

qualified service personnel.

During storm conditions

(especially when there is

lightning) unplug your set from

the mains socket and aerial.

If the remote control is not

used for a long period of time,

remove the batteries and store

it in a cool, dry place.

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

apollo_en 12/23/02 5:24 PM Page 3

English-4

Contents

◆ FOREWORD

■

Safety Instructions .......................................................................................... 3

■

Caution .......................................................................................................... 3

◆ CONNECTING AND PREPARING YOUR TV

■

Viewing the Control Panel.............................................................................. 6

■

Viewing the Connection Panel ....................................................................... 7

-

Connecting an Aerial or Cable Television Network..................................... 8

-

Connecting External A/V Devices ............................................................... 8

-

Connecting DTV Set-Top Box, VCR, or DVD.............................................. 8

-

Connecting Computer................................................................................. 8

-

Connecting Sound Outputs......................................................................... 8

-

Connecting Digital Audio Inputs................................................................. 9

-

Connecting Speakers................................................................................... 9

■

Viewing Pictures From External Sources......................................................... 9

■

Viewing the Remote Control (All Functions Except Teletext)........................... 10

■

Viewing the Remote Control (Teletext Functions) ........................................... 11

■

Inserting the Batteries in the Remote Control.................................................. 12

■

Switching On and Off .................................................................................... 12

■

Becoming Familiar with the Remote Control.................................................. 13

■

Choosing Your Language................................................................................ 14

◆ SETTING THE CHANNELS

■

Storing Channels Automatically...................................................................... 15

■

Storing Channels Manually............................................................................. 16

■

Giving Channels Names................................................................................. 18

■

Skipping Unwanted Channels ........................................................................ 19

■

Fine Tuning Channel Reception...................................................................... 19

■

Sorting the Stored Channels ........................................................................... 20

◆ USING THE VARIOUS FUNCTIONS

■

Changing the Picture Standard ....................................................................... 21

■

Adjusting the Picture Settings ......................................................................... 21

■

Selecting the Picture Format........................................................................... 22

■

Freezing the Current Picture........................................................................... 22

■

Changing the Sound Standard ........................................................................ 23

■

Adjusting the Sound Settings .......................................................................... 23

■

Enjoying the Dolby Sound (LW29A13W) ....................................................... 24

■

Switching the Internal Woofers On/Off (LW29A13W) .................................... 24

apollo_en 12/23/02 5:24 PM Page 4

English-5

Contents

◆ USING THE VARIOUS FUNCTIONS

■

Setting the External Digital Sound (LW40A13W) ............................................ 25

■

Setting the Dolby Digital (LW40A13W).......................................................... 26

■

Setting the Dolby Pro-Logic (LW40A13W) ..................................................... 27

■

Selecting the Sound Mode.............................................................................. 28

■

Viewing the Picture In Picture (PIP) ................................................................ 29

■

Selecting the Sleep Timer ............................................................................... 31

■

Setting and Displaying the Current Time ........................................................ 32

■

Switching the Television On and Off Automatically ....................................... 33

■

DNIe (Digital Natural Image engine) ............................................................. 34

◆ USING THE PC FUNCTIONS

■

Setting up Your PC Softerware (Based on Windows 2000 or XP) .................... 35

■

Adjusting the Contrast and Brightness ............................................................ 36

■

Selecting the Image Size................................................................................. 36

■

Adjusting the Image Quality........................................................................... 37

■

Changing the Image Position.......................................................................... 37

■

Adjusting the Colour ...................................................................................... 38

■

Initializing the Image Settings......................................................................... 39

■

Adjusting the PC Screen Automatically .......................................................... 39

◆ USING THE TELETEXT FEATURE

■

Teletext Feature .............................................................................................. 40

■

Displaying the Teletext Information................................................................ 41

■

Selecting Display Options .............................................................................. 41

■

Selecting a Teletext Page ................................................................................ 42

◆ RECOMMENDATIONS FOR USE

■

Troubleshooting: Before Contacting Service Personnel ................................... 43

■

PowerSaver .................................................................................................... 44

■

Technical and Environmental Specifications................................................... 45

■

Display Modes ............................................................................................... 46

■

Wiring the Mains Power Supply Plug (UK Only) ............................................ 47

☛

➢

Press Important Note

Symbols

apollo_en 12/23/02 5:24 PM Page 5

English-6

Viewing the Control Panel

(Power)

Turns ON/OFF your set.

Power Indicator

Remote Control Sensor

TV/VIDEO

Displays a menu of all of the available input

sources (TV, VIDEO, S-VIDEO, EXT1, EXT2,

PC Analog, PC Digital).

MENU

Opens the OSD and selects the function.

▼ C/P. ▲

Moves the selector up or down on the OSD.

Increases or decreases the channel number.

Switches on the TV when it is in Standby mode.

-

+

Moves the selector left or right on the OSD.

Increases or decreases the level of audio volume

and the values of the selected function.

1

5

6

7

2

3

4

apollo_en 12/23/02 5:24 PM Page 6

English-7

Viewing the Connection Panel

2

1

7

4

3

5

8

LW29A13W

LW40A13W

5

6

☛

Whenever you connect an audio or video system to your set, ensure that all elements are switched

off

. Refer to the documentation supplied with your equipment for detailed connection instructions

and associated safety precautions.

Power Input

apollo_en 12/23/02 5:24 PM Page 7

English-8

Viewing the Connection Panel

Connecting an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:

- An outdoor aerial

- A cable television network

- A satellite network

Connecting External A/V Devices

- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD, or Camcorder.

- Connect RCA audio cables to “

AUDIO(L)” and “AUDIO(R)” on the rear of your set and the other ends to

corresponding audio out connectors on the A/V device.

- Headphone may be connected to the headphone output ( ) on the rear of your set.

While the headphone

is connected, the sound from the built-in speakers will be disabled.

Connecting DTV Set-Top Box, VCR, or DVD

- Connect the DTV, VCR, or DVD EXT cable to the EXT connector of the DTV, VCR, or DVD.

- If you wish to connect both the DTV Set-Top Box and VCR (or DVD), you should connect the DTV Set-Top

Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.

Connecting Computer

- Connect the DVI connector to the PC video connector.

- Connect the stereo audio cable to ”

PC AUDIO(ST)” on the rear of your set and the other end to “Audio Out”

of the sound card on your computer.

➣

DVI connector

Connecting Sound Outputs

Connect RCA audio cables to an audio system or external amplifier.

Pin Description

1 Rx 2-

2 Rx 2+

3 Grounding

4 No connection

5 No connection

6 DDC Clock (SCL)

7 DDC Data (SDA)

8 Analog Vertical Sync

9 Rx 1-

10 Rx 1+

11 Grounding

12 No connection

13 No connection

14 DDC Input Power (+5V)

15 Self Laster

Pin Description

16 Output Signal Connection

17 Rx 0-

18 Rx 0+

19 Grounding

20 No connection

21 No connection

22 Grounding

23 Rx C-

24 Rx C+

25(C3) Analog (Blue)

26(C5) Analog Grounding

27(C4) Analog Horizontal sync.

28(C2) Analog (Green)

29(C5) Analog Grounding

30(C1) Analog (Red)

1

2

3

4

5

8

apollo_en 12/23/02 5:24 PM Page 8

English-9

Viewing the Connection Panel

Connecting Digital Audio Inputs

Connect RCA audio cables to a equipment with a digital output (to take digital sound).

Connecting Speakers

(depending on the model)

or

Viewing Pictures From External Sources

Once you have connected up your various audio and video systems,

you can view the different sources by selecting the appropriate input.

1 Check that all the necessary connections have been made (refer to

pages 8 and 9 for further details).

2 Switch your set on and if necessary, press the VIDEO button

repeatedly. The input sources are displayed in the following order:

TV

-

VIDEO

-

S-VIDEO

-

Ext1

-

Ext2

-

PC Analog

-

PC Digital.

➣

To watch television programme again, press the TV button.

Mount the brackets on the speaker

and your set.

Connect the speaker and your set

using screws.

Connect the speaker audio cable to the external

speaker output jack on the rear of your set making

sure that the

+,

-

polarities are correctly aligned.

➢

The speakers MUST have more than 7watts

rating (impedance 8Ω).

6

7

apollo_en 12/23/02 5:24 PM Page 9

English-10

Viewing the Remote Control (All Functions Except Teletext)

PIP

One/Two-digit channel selection

Picture size selection

VCR/DVD Functions:

- Stop

- Rewind

- Play/Pause

- Fast-Forward

Volume decrease

On-screen display

Available sources selection

Numeric buttons for

direct channel access

Picture-In-Picture Functions:

-

PIP On/Off

-

PIP size selection (SIZE)

-

PIP channel selection (P▲/▼)

(Not available for LW29A13W)

-

Interchange the main and sub picture

(

SWAP)

-

PIP freeze (STILL) : Not available

-

PIP location selection (LOCATE)

-

PIP channel scan (SCAN)

-

PIP source selection (TV/VIDEO)

Sound mode selection

Previous channel

Television On/Off

➣

The performance of the remote control may be affected by bright light.

Picture freeze

(Not Available in PC mode)

Make the remote control work for

TV, VCR, Cable, DVD player.

Volume increase

Sound menu display

Picture menu display

Picture effect selection

TV mode selection directly

Sound effect selection

Temporary sound switch-off

Next channel

Menu display/

Exit from the OSD

Automatic switch-off

Not available

apollo_en 12/23/02 5:24 PM Page 10

English-11

Viewing the Remote Control (Teletext Functions)

PIP

Teletext display/

Mix both teletext information and

the normal broadcast

Teletext sub-page

Teletext size selection

Fastext topic selection

Teletext index

Teletext reveal

apollo_en 12/23/02 5:24 PM Page 11

English-12

Inserting the Batteries in the Remote Control

You must insert or replace the batteries in the remote control when

you:

◆

Purchase your set

◆

Find that the remote control is no longer operating

correctly

1 Remove the cover on the rear of the remote control by pressing the

symbol downwards and then pulling firmly to remove it.

2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to

respect the polarities:

◆

+

on the battery against

+

on the remote control

◆

-

on the battery against

-

on the remote control

3 Replace the cover by aligning it with the base of the remote control

and pressing it back into place.

➣

Do not mix battery types, i.e. alkaline and monganese.

Switching On and Off

The mains lead is attached to the rear of your set.

☛

If you have purchased this set in the United Kingdom, refer to

page 45 for further instructions on plug wiring.

1 Plug the mains lead into an appropriate socket.

Result

:

A green Standby indicator appears on the front of your set.

2 Press the POWER ( ) or channel up/down (P /, ▼C/P. ▲)

button.

Result

:

The screen is turned on and a green Standby indicator

disappears on the front of your set.

Your set can be placed in Standby mode, in order to reduce the power

consumption. The Standby mode can be useful when you wish to

interrupt viewing temporarily (during a meal, for example).

1 Press the POWER ( ) button.

Result

:

The screen is turned off and a green Standby indicator

appears on the front of your set.

2 To switch your set back on, simply press the POWER ( ) button

again.

➣

Do not leave your set in Standby mode for long periods of time

(when you are away on holiday, for example). Turn your set off by

unpluging from the mains and aerial.

apollo_en 12/23/02 5:24 PM Page 12

English-13

Becoming Familiar with the Remote Control

The remote control is used mainly to:

◆

Change channels and adjust the volume

◆

Set up your set using the on-screen menu system

The following table presents the most frequently used buttons and

their functions.

Button Viewing Function Menu Function

Used to display the next Used to select the previous

P stored channel. menu option.

P Used to display the Used to select the next menu

previous stored channel. option.

to Used to display the corresponding channels.

-/--

Used to select a channel numbered ten or over.

Press this button, and the “

--

” symbol is displayed.

Enter the two-digit channel number.

Used to decrease the Used to...

volume.

◆ Display a submenu containing

selections for the current

menu option.

◆ Search forwards manually

for channels

◆ Reduce a menu option value.

Used to increase the Used to...

volume.

◆ Display a submenu containing

selections for the current

menu option.

◆ Search backwards manually

for channels

◆ Increase a menu option value.

MUTE Used to switch the sound off temporarily.

➣

To turn the sound back on, press this button again,

or press the

-

or

+

button.

MENU Used to display the Used to return to the previous

on-screen menu system. menu or normal viewing.

PIP

apollo_en 12/23/02 5:24 PM Page 13

English-14

Choosing Your Language

When you start using your set for the first time, you must select the

language which will be used for displaying menus and indications.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Function.

Result

:

The options available in the

Function

group are

displayed.

3 Press the

-

or

+

button

.

4 Press the P or P button

to

select the Language

.

5 Select a particular language by pressing the

-

or

+

button

repeatedly.

6 When you are satisfied with your choice, press the MENU button to

return to normal viewing.

Function

Time

PIP

Language English

DNIe Off

apollo_en 12/23/02 5:24 PM Page 14

English-15

Storing Channels Automatically

You can scan for the frequency ranges available to you (and

availability depends on your country). Automatically allocated

programme numbers may not correspond to actual or desired

programme numbers. However you can sort numbers manually and

clear any channels you do not wish to watch.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button.

Result

:

The

Auto store

is selected.

4 Press the

-

or

+

button again.

Result

:

The options available in the

Auto store

group are

displayed when the

Country

is selected.

5 Select your country by pressing the

-

or

+

button repeatedly.

The following countries are available:

Belgie

-

Deutschland

-

Espania

-

France

-

Italia

-

Nederland

-

Schweiz

-

Sverige

-

UK

-

East Europe.

6 Press the P or P button to select the Search, and then press

the

-

or

+

button.

Result

:

The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the

frequency range, (with lowest first and highest last).

The programme originally selected is then displayed.

➣

To stop the search before it has finished, press the

MENU

button.

7 When the channels have been stored, you can:

◆ Change channels

◆ Assign a name to the stored channels (refer to page 18)

◆ Clear a channel (refer to page 19)

◆ Fine tune channel reception if necessary (refer to page 19)

◆ Sort them in the order required (refer to page 20)

Channel

Auto store

Manual store

Name

Add/Erase

Fine tune

Channel sort

Channel

Country UK

Search

Channel

Country UK

Search

Program 1

Frequency 205MHz

Band VHF-H

apollo_en 12/23/02 5:24 PM Page 15

English-16

Storing Channels Manually

You can store up to 100 channels, including those received via cable

networks. When storing channels manually, you can choose:

◆

Whether or not to store each of the channels found

◆

The programme number of each stored channel which you

wish to identify

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button

.

4 Press the P or P button

to

select the Manual store

.

Press the

-

or

+

button.

Result

: The options available in the Manual store group are

displayed with the

Colour system is selected.

5 If necessary, indicate the broadcasting standard required by pressing

the

-

or

+

button repeatedly.

Result

: The colour standards are displayed in the following order:

AUTO

-

PAL

-

SECAM

-

NT4.43.

6 Press the P or P button to select the Sound system. Indicate

the sound standard required by pressing the

-

or

+

button

repeatedly.

Result

: The sound standards are displayed in the following order:

BG

-

DK

-

I

-

L.

Channel

Auto store

Manual store

Name

Add/Erase

Fine tune

Channel sort

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA Off

Store ?

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA Off

Store ?

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA Off

Store ?

apollo_en 12/23/02 5:24 PM Page 16

English-17

Storing Channels Manually

7 If you know the channel number to be stored, press the P or P

button to select the Channel. Indicate the required number by

pressing the

-

or

+

button.

If you do not know the channel numbers, press the

P or P

button to select the Search.

Start the search by pressing the

-

or

+

button.

Result

: The tuner scans the frequency range until the first

channel or the channel that you selected is received on

your screen.

8 To assign a programme number to a channel, select the Program by

pressing the

P or P button.

Press the

-

or

+

button to find the correct number.

9 Press the P or P button to select the LNA

..(LW40A13W)

Select the On by pressing the

-

or

+

button

.

Result: Amplifies signals when antenna reception is poor.

However if incoming signals are interfering with each

other, turn off LNA as it may malfuction.

10 Press the P or P button to select the Store

.

Select the OK by pressing the

-

or

+

button

.

Result: The channel and associated programme number are

stored.

11 Repeat Steps 7 to 9 for each channel to be stored.

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA Off

Store ?

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA Off

Store ?

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA ON

Store ?

Channel

Colour system AUTO

Sound system BG

Search 0MHz

Channel C 1

Program P 1

LNA ON

Store ?

apollo_en 12/23/02 5:24 PM Page 17

English-18

Giving Channels Names (Except Russian OSD)

If channel name information is broadcast when you store the channels

either manually or automatically, the names are assigned to the

channels directly. You can however change these names or assign new

names as required.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button

.

4 Press the P or P button to select the Name

.

Press the

-

or

+

button.

Result

:

The current channels are displayed.

5 If necessary, select the channel to be assigned to a new name by

pressing the

P or P button.

6 Press the

-

or

+

button.

7 Press the P or P button to select a letter (A~Z), a number

(0~9) or a symbol (

-

, space).

Move on the previous or next letter by pressing the

-

or

+

button.

8 Repeat Steps 5 to 7 for each channel to be assigned to a new

name.

apollo_en 12/23/02 5:24 PM Page 18

English-19

Skipping Unwanted Channels

You can exclude the channels you chosen from the channels you

scanned. When you scan through the stored channels, those you have

chosen to skip are not displayed.

All channels that you do not specifically choose to skip are displayed

during scanning.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button.

4 Press the P or P button to select the Add/Erase

.

Press the

-

or

+

button.

Result

:

The stored channels are displayed.

5 Press the P or P button to select the channel to add or erase.

If necessary, select the

Added or Erased by pressing the

-

or

+

button.

6 Repeat Step 5 for each channel to be added or erased.

Fine Tuning Channel Reception

If the reception is clear, you do not have to fine-tune the channel,

as this is done automatically during the search and store operation.

If however the signal is weak or distorted, you may have to fine-tune

the channel manually.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button

.

4 Press the P or P button to select the Fine tune.

5 Obtain a sharp and clear picture and good sound quality by pressing

the

-

or

+

button.

Channel

Auto store

Manual store

Name

Add/Erase

Fine tune

Channel sort

Fine tune

+ 1

apollo_en 12/23/02 5:24 PM Page 19

English-20

Sorting the Stored Channels

You can exchange the numbers of two channels, in order to:

◆

Modify the numeric order in which the channels have been

automatically stored.

◆

Give easily remembered numbers to the channels that you

watch most often.

1 Press the MENU button.

Result

:

The main menu is displayed.

2 Press the P or P button to select the Channel.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

-

or

+

button

.

4 Press the P or P button to select the Channel sort

.

Press the

-

or

+

button.

Result:

The options available in the

Channel sort

group are

displayed with the

From

is selected.

5 Select the channel number that you wish to change by pressing the

-

or

+

button repeatedly.

6 Press the P or P button to select the To. Select the new

number by which you wish to identify the channel by pressing the

-

or

+

button repeatedly.

7 Press the P or P button to select the Store. Select the OK to

confirm the exchange of channel numbers by pressing the

-

or

+

button.

Result

:

The selected channel is exchanged with the one

previously stored to the chosen number.

8 For all the channels to move to the required channel numbers,

repeat steps

5 to 7 after select the From by pressing the

P or P button.

Channel

Auto store

Manual store

Name

Add/Erase

Fine tune

Channel sort

From P 1 -----

To P--

Store ?

Channel sort

From P 1 -----

To P 3 -----

Store ?

Channel sort

From P 3 -----

To P 1 -----

Store OK

apollo_en 12/23/02 5:24 PM Page 20

Page is loading ...

Samsung LW29A13W User manual

This manual is also suitable for

Samsung LW29A13W User manual

Related papers

Other documents