Samsung WD8704CJF/YAS User guide

Washing Machine

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/register

WD8704EJ(A/F/G/H/S/V/W/Z)

WD8702EJ(A/F/G/H/S/V/W/Z)

WD8700EJ(A/F/G/H/S/V/W/Z)

WD8704RJ(A/F/G/H/S/V/W/Z)

WD8702RJ(A/F/G/H/S/V/W/Z)

WD8700RJ(A/F/G/H/S/V/W/Z)

WD8704CJ(A/F/G/H/S/V/W/Z)

WD8702CJ(A/F/G/H/S/V/W/Z)

WD8700CJ(A/F/G/H/S/V/W/Z)

WD8704DJ(A/F/G/H/S/V/W/Z)

WD8702DJ(A/F/G/H/S/V/W/Z)

WD8700DJ(A/F/G/H/S/V/W/Z)

WD8704CJ-02766A-04_EN.indd 1WD8704CJ-02766A-04_EN.indd 1 2011-03-17  6:26:082011-03-17  6:26:08

2_ features

features of your new samsung

washing machine

Your new washing machine will change the way you feel about doing laundry. From

its super-size capacity to its energy efﬁ ciency, the Samsung washing machine has

all the features to turn a mundane chore into a pleasure.

• Silver Wash - Silver Wash Health System(selected model only)

The winning combination! Samsung’s silver technology combines the sanitizing effect of silver

with state-of-the-art science for the ultimate in clean. Two plates of pure silver are converted

into silver ions through electrolysis. Even in cold, bleach-less water, the silver particles remove

of odor causing bacteria for a “super clean” wash. So washing in cold water is energy efﬁ cient

and better for your clothes.

The Silver plates carry a warranty of ten years for 1 time run a week and can easily be

replaced by a Service Technician if needed.

• Washing to drying with one button

Enjoy convenient non stop washing and drying managing. 4 different special drying programs

can be selected to perform the whole wash cycle including the drying cycle using one button.

• Cupboard(standard program), Low temp drying, Iron,Time Drying (30min ~ 270mins)

Those drying programs also can be operated independently of washing programs.

• Child Lock

The Child Lock function ensures that curious little hands are kept out of your washing

machine.

This safety feature stops your children from playing with the operation of the washing

machine, and alerts you when it is activated.

• Wool Certiﬁ ed

The machine has been tested and passed the required Woolmark Company speciﬁ cation for

machine washable wool products.

Fabrics should be washed according to the instructions on the garment label as speciﬁ ed by

Woolmark and Samsung.

• Delay End

Delay a cycle for up to 19 hours in one-hour increments and increase the convenience of

using your washing machine especially when you have to go out.

• Quick Wash

No time to lose! Less than 30 minutes wash will give you time to run out before it’s too late.

Our 29 minute Quick Wash program can be the solution to your busy life. Now you can wash

your favourite clothes in only 29 minutes!

• Delicates & Hand Wash Program

Special care can be determined by the appropriate temperature, the gentle wash action and

the appropriate amount of water.

• Ceramic Heater for Durability & Energy Saving (selected models)

Our truly innovative Ceramic Heater is twice as durable as regular heaters.

That saves you money on repairs. Plus, it eliminates the scale of hard water and save energy.

WD8704CJ-02766A-04_EN.indd Sec1:2WD8704CJ-02766A-04_EN.indd Sec1:2 2011-03-17  6:27:092011-03-17  6:27:09

features _3

• Air Wash

The Air Wash system deodorizes unpleasant smells and sterilizes the laundry that cannot

be eliminated through a conventional washing system, a beneﬁ t of its unique air-washing

mechanism.

• Air-washable : Woolen coats, cotton/down jumpers, sweaters, suits, pillows, cushions,

needlework dolls

• Not applicable : leather, silk, velvet, electric blankets, other stained laundry

• Digital Graphic Display

The Digital Graphic Display control panel is clear and easy to use for minimum fuss and

hassle. And while it is easy to operate, the Digital Graphic Display enables you to make quick

and accurate adjustments to your wash for excellent washing results.

• Wide door

Extra wide door aperture for convenient viewing! Easily add and remove laundry, especially for

large sized laundry items such as bedding, towels etc.

• Direct Drive Motor

As the drum does not utilize belts or gears, vibrations are reduced signiﬁ cantly. This feature

ensures that your washer machine is quieter and more durable.

This manual contains important information on the installation, use, and care of your new

Samsung washing machine. Refer to it for descriptions of the control panel, instructions on how

to use the washing machine, and tips for making the most of its state-of-the-art features and

functions. The “Troubleshooting and information codes” section on page 29 tells you what to

do if something goes wrong with your new washing machine.

WD8704CJ-02766A-04_EN.indd Sec1:3WD8704CJ-02766A-04_EN.indd Sec1:3 2011-03-17  6:27:092011-03-17  6:27:09

4_ safety information

safety information

Throughout this manual, you’ll see Warning and Caution notes. These

warnings, cautions, and the important safety instructions that follow do not cover

all possible conditions and situations that may occur. It’s your responsibility to use

common sense, caution, and care when installing, maintaining, and operating your

washing machine. Samsung is not liable for damages resulting from improper use.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury

or death.

CAUTION

Hazards or unsafe practices that may result in minor personal injury or

property damage.

CAUTION

To reduce the risk of ﬁ re, explosion, electric shock, or personal

injury when using your washing machine, follow these basic safety

precautions:

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Notice

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

As with any equipment using electricity and moving parts, potential hazards exist. To safely

operate this appliance, become familiar with its operation and exercise care when using it.

Install and store your washing machine inside, away from exposure to weather.

Install and level your washing machine on a ﬂ oor that can support its weight.

Your washing machine must be properly grounded. Never plug it into an ungrounded outlet.

WD8704CJ-02766A-04_EN.indd Sec2:4WD8704CJ-02766A-04_EN.indd Sec2:4 2011-03-17  6:27:092011-03-17  6:27:09

safety information _5

To reduce the risk of ﬁ re or explosion:

• Do not wash items that have been washed, soaked, or treated with gasoline, dry

cleaning solvents, or other ﬂ ammable or explosive substances. They give off vapors that

could ignite or explode. Rinse by hand any material that has been exposed to cleaning

solvent or other ﬂ ammable liquids or solids before putting in your washing machine. Be

sure that all traces of such liquids, solids, and fumes have been removed. Dangerous

substances include acetone, denatured alcohol, gasoline, kerosene, certain liquid

household cleaners and spot removers, turpentine, waxes, and wax removers.

• Do not put gasoline, dry cleaning solvents, or other ﬂ ammable or explosive substances

into the washing machine.

• Under certain conditions, hydrogen gas may be produced in a hot water system–such

as your hot water heater -- that has not been used for two weeks or more. HYDROGEN

GAS IS EXPLOSIVE. If your hot water system has not been used for two weeks or

more, turn on all hot water taps in your home, and let the water ﬂ ow for several minutes

before using your washing machine. This will release any hydrogen gas build–up. Since

hydrogen gas is ﬂ ammable, do not smoke or light an open ﬂ ame during this time.

Ventilate immediately without touching the power plug if there is a gas leak.

Unplug the power cord before servicing your washing machine.

Before each wash, empty the pockets of your laundry. Small, irregularly shaped hard

objects, such as coins, knives, pins, and paperclips could damage your washing machine.

Do not wash clothing with large buckles, buttons, or other heavy metal metal.

Do not open the door of the washing machine if you can still see water. Check that the

water has drained before opening the door.

Do not repair, replace, or service any part of your washing machine yourself unless you fully

understand the recommended user–repair instructions and have the skills to carry them

out. Work done by an unauthorized person may void your warranty.

Connect the washing machine to the water mains using the new set of hoses. Do not reuse

the old set of hoses.

Water inlet hoses deteriorate over time. Check the hoses periodically for bulges, kinks, cuts,

wear, and leaks, and replace them as needed and at least every ﬁ ve years.

All packaging and shipping bolts must be removed before the appliance is used. Serious

damage may occur if they are not removed. See page 12 “Removing the shipping bolts”.

Before washing clothes for the ﬁ rst time, you must run a complete cycle without clothes.

See “Washing for the ﬁ rst time”.

CAUTION

WD8704CJ-02766A-04_EN.indd Sec2:5WD8704CJ-02766A-04_EN.indd Sec2:5 2011-03-17  6:27:112011-03-17  6:27:11

6_ safety information

The appliance is designed for home use only.

Make sure that water and electrical connections are made by qualiﬁ ed technicians,

observing the user manual (see “Installing your washing machine”) and local safety

regulations.

Before cleaning or carrying out maintenance, unplug the appliance from the electrical outlet.

Always unplug the appliance and turn off the water after use.

Make sure that the pockets of all clothing to be washed are empty.

Hard, sharp objects, such as coins, safety pins, nails, screws, or stones can cause

extensive damage to the appliance.

Never allow pets and children to play on or in the appliance. It may cause injury or suffocate

them.

The glass door becomes very hot during the washing cycle. Never touch on the glass door

while it is in use.

Do not attempt to repair the appliance yourself. Repairs made by inexperienced or

unqualiﬁ ed persons may cause injury and/or make more serious repairs to the appliance

necessary.

If the plug (power supply cord) is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualiﬁ ed person in order to avoid a hazard.

This appliance should only be serviced by our authorized service center, and only rated

spare parts should be used.

Do not let children (or pets) play on or in your washing machine. The washing machine door

does not open easily from the inside, and children may be seriously injured if trapped inside.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the appliance

To use this appliance safely, the user should become familiar with the instructions for

operation of the appliance and always take extra care when using it.

This appliance should be positioned to be accessible to the power plug, the water supply

tabs and the drain pipes.

Packing materials can be dangerous to children; keep all packing material (plastic bags,

polystyrene, etc.) well out of the reach of children.

Do not use processed water containing oil, cream or lotion, which is usually found in

skincare shops or massage clinics.

• Otherwise this will cause the packing to be deformed, which causes a malfunction or

water leak.

safety information

WARNING

WD8704CJ-02766A-04_EN.indd Sec2:6WD8704CJ-02766A-04_EN.indd Sec2:6 2011-03-17  6:27:112011-03-17  6:27:11

safety information _7

A stainless washing tub does not usually rust. However if some metal such as a hair pin is

left in the tub for an extended time, the tub could rust.

• Do not leave water or bleach containing chlorine in the tub for an extended period of

time.

• Do not regularly use or leave water containing iron in the tub for an extended period of

time. If rust starts appearing on the surface of the tub, apply a cleansing agent (neutral)

to the surface and use a sponge or soft cloth to clean it. (Under no circumstances use a

metal brush)

The dryer is not to be used if chemicals have been used for cleaning.

For washing machines with ventilation openings in the base, ensure that the opening is not

obstructed by carpet or any other obstacles.

Use the new hose-sets and old hose-sets should not be reused.

WD8704CJ-02766A-04_EN.indd Sec2:7WD8704CJ-02766A-04_EN.indd Sec2:7 2011-03-17  6:27:122011-03-17  6:27:12

8_ contents

contents

SETTING UP YOUR WASHING

MACHINE

9

9 Checking the parts

10 Meeting installation requirements

10 Electrical supply and grounding

10 Water Supply

11 Drain

11 Flooring

11 Surrounding temperature

11 Alcove or closet installation

11 Installing your washing machine

WASHING A LOAD OF LAUNDRY

17

17 Washing for the ﬁ rst time

17 Basic instructions

18 Using the control panel

20 Child lock

20 Sound off

20 Delay end

20 Drain Only Fuction

21 Air Wash

22 Using dry course

23 Washing clothes using the cycle selector

23 Washing clothes manually

24 Laundry guidelines

25 Detergent and additives information

25 Which detergent to use

26 Detergent drawer

CLEANING AND MAINTAINING YOUR

WASHING MACHINE

27

27 Draining the washing machine in an

emergency

27 Cleaning the exterior

28 Cleaning the detergent drawer and drawer

recess

29 Cleaning the debris ﬁ lter

29 Cleaning the water hose mesh ﬁ lter

29 Repairing a frozen washing machine

29 Storing your washing machine

TROUBLESHOOTING AND

INFORMATION CODES

30

30 Check these points if your washing machine...

31 Information codes

CYCLE CHART

32

32 Cycle chart

APPENDIX

33

33 Fabric care chart

33 Protecting the environment

33 Declaration of conformity

34 Speciﬁ cations

WD8704CJ-02766A-04_EN.indd Sec3:8WD8704CJ-02766A-04_EN.indd Sec3:8 2011-03-17  6:27:122011-03-17  6:27:12

setting up your new washing machine _9

01 SETTING UP

setting up your washing

machine

Be sure to have your installer follow these instructions closely so that your new

washing machine works properly and so that you’re not at risk of injury when doing

laundry.

CHECKING THE PARTS

Carefully unpack your washing machine, and make sure you’ve received all of the parts shown below.

If your washing machine was damaged during shipping, or if you do not have all of the parts, contact

Samsung Customer Service or your Samsung dealer.

Spanner *Bolt hole covers Water supply hose Hose guide

* Bolt hole covers : The number of bolt hole covers depends on the model (3~5 covers).

Detergent drawer

Control panel

Door

Adjustable feet

Work top

Plug

Drain hose

Debris ﬁ lter

Emergency drain tube

Filter Cover

Tub

Release lever

WD8704CJ-02766A-04_EN.indd Sec4:9WD8704CJ-02766A-04_EN.indd Sec4:9 2011-03-17  6:27:122011-03-17  6:27:12

10_ setting up your new washing machine

setting up your washing

machine

MEETING INSTALLATION REQUIREMENTS

Electrical supply and grounding

To prevent unnecessary risk of ﬁ re, electrical shock, or personal injury, all wiring and grounding

must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest

Revision and local codes and ordinances. It is the personal responsibility of the appliance owner

to provide adequate electrical service for this appliance.

Never use an extension cord.

Use only the power cord that comes with your washing machine.

When preparing for installation, ensure that your power supply offers:

• 220V~240V 50Hz 15 AMP fuse or circuit breaker

• Individual branch circuit serving only your washing machine

Your washing machine must be grounded. If your washing machine malfunctions or breaks

down, grounding will reduce the risk of electric shock by providing a path of least resistance for

the electric current.

Your washing machine comes with a power cord having a three-prong grounding plug for use in

a properly installed and grounded outlet.

Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

Improperly connecting the equipment-grounding conductor can result electrical shock.

Check with a qualiﬁ ed electrician or serviceman if you are unsure if the washing machine is

properly grounded. Do not modify the plug provided with the washing machine. If it does not ﬁ t

the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

Water Supply

Your washing machine will ﬁ ll properly when your water pressure is 50 kPa ~ 800 kPa. Water

pressure less than 50 kPa may cause water valve failure, not allowing the water valve to shut

off completely. Or, it may take the washing machine longer to ﬁ ll than what the controls allow,

resulting in your washing machine turning off. (A ﬁ ll-time limit, designed to prevent overﬂ ows/

ﬂ ooding if an internal hose becomes loose, is built into the controls.)

The water taps must be within 4 feet (122cm) of the back of your washing machine for the

provided inlet hoses provided to reach your washing machine.

Most plumbing supply stores sell inlet hoses of various lengths up to 10 feet (305cm) long.

You can reduce the risk of leaks and water damage by:

• Making water taps easily accessible.

• Turning off taps when the washing machine is not in use.

• Periodically checking for leaks at water inlet hose ﬁ ttings.

Before using your washing machine for the ﬁ rst time, check all connections at the water

valve and taps for leaks.

WARNING

WD8704CJ-02766A-04_EN.indd Sec4:10WD8704CJ-02766A-04_EN.indd Sec4:10 2011-03-17  6:27:132011-03-17  6:27:13

setting up your new washing machine _11

01 SETTING UP

Drain

Samsung recommends a standpipe height of 18 in (46 cm). The drain hose must be routed

through the drain hose clip to the standpipe. The standpipe must be large enough to accept the

outside diameter of the drain hose. The drain hose is attached at the factory.

Flooring

For best performance, your washing machine must be installed on a solidly constructed ﬂ oor.

Wood ﬂ oors may need to be reinforced to minimize vibration and/or unbalanced loads. Carpeting

and soft tile surfaces are contributing factors to vibrations and the tendency for your washing

machine to move slightly during the spin cycle.

Never install your washing machine on a platform or poorly supported structure.

Surrounding temperature

Do not install your washing machine in areas where water may freeze, since your washing

machine always retains some water in its water valve, pump, and hose areas. Frozen water in

the lines can cause damage to belts, the pump, and other components.

Alcove or closet installation

To operate safely and properly, your new washing machine requires minimum clearances of:

Sides – 25 mm Rear – 51 mm

Top – 25 mm Front – 465 mm

If both the washing machine and a dryer are installed together, the front of the alcove or closet

must have at least 465 mm unobstructed air opening. Your washing machine alone does not

require a speciﬁ c air opening.

INSTALLING YOUR WASHING MACHINE

STEP 1

Selecting a location

Before you install the washing machine, make sure the location:

• Has a hard, level surface without carpeting or ﬂ ooring that may obstruct ventilation

• Is away from direct sunlight

• Has adequate ventilation

• Will not be freezing (below 32 ˚F or 0 ˚C)

• Is away from heat sources such as oil or gas

• Has enough space so that the washing machine doesn’t stand on its power cord

WD8704CJ-02766A-04_EN.indd Sec4:11WD8704CJ-02766A-04_EN.indd Sec4:11 2011-03-17  6:27:142011-03-17  6:27:14

12_ setting up your new washing machine

STEP 2

Removing the shipping bolts

Before installing the washing machine, you must remove all shipping bolts from the back of the

unit.

1. Loosen all the bolts with the supplied wrench.

2. Hold the bolt with the spanner and pull it through the wide

section of the hole. Repeat for each bolt.

3. Fill the holes with the supplied plastic covers.

4. Store the shipping bolts away safely in case you have to move the washing machine in the

future.

Packaging materials can be dangerous to children; keep all packaging material (plastic

bags, polystyrene, etc.) well out of the reach of children.

setting up your washing

machine

WARNING

WD8704CJ-02766A-04_EN.indd Sec4:12WD8704CJ-02766A-04_EN.indd Sec4:12 2011-03-17  6:27:142011-03-17  6:27:14

setting up your new washing machine _13

01 SETTING UP

STEP 3

Adjusting the levelling feet

When installing your washing machine, ensure that the power plug, the water supply and

the drain are easily accessible.

1. Slide the washing machine into position.

2. Level your washing

machine by turning the

leveling feet in and out as

necessary by hand.

3. When your washing machine is level, tighten the nuts using

the wrench supplied with your washing machine.

STEP 4

Connecting the water and drain

Connecting the water supply hose

1. Take the L-shaped arm ﬁ tting for the cold water

supply hose and connect it to the cold water

supply intake on the back of the machine.

Tighten by hand.

The water supply hose must be connected

to the washing machine at one end and to

the water tap at the other. Do not stretch the

water supply hose. If the hose is too short,

replace the hose with a longer, high pressure

hose.

2. Connect the other end of the cold water supply

hose to your sink’s cold water tap and tighten

it by hand. If necessary, you can reposition the

water supply hose at the washing machine end

by loosening the ﬁ tting, rotating the hose, and

retightening the ﬁ tting.

For selected models with an additional hot water intake:

1. Take the red L-shaped arm ﬁ tting for the hot water supply hose and connect it to the hot

water supply intake on the back of the machine. Tighten by hand.

2. Connect the other end of the hot water supply hose to your sink’s hot water tap and tighten

it by hand.

3. Use a Y-piece if you only want to use cold water.

WD8704CJ-02766A-04_EN.indd Sec4:13WD8704CJ-02766A-04_EN.indd Sec4:13 2011-03-17  6:27:142011-03-17  6:27:14

14_ setting up your new washing machine

Connecting the water supply hose (selected models)

1. Remove the adaptor from the water supply hose.

2. First, using a ‘+’ type screwdriver, loosen the four screws

on the adaptor. Next, take the adaptor and turn part (2)

following the arrow until there is a 5 mm gap.

3. Connect the adaptor to the water tap by tightening the

screws ﬁ rmly while lifting the adaptor upwards.

Turn part (2) following the arrow and connect (1) and (2).

4. Connect the water supply hose to the adaptor.

When you release part (3), the hose automatically

connects to the adaptor making a ‘click’ sound.

After you have connected the water supply

hose to the adaptor, ensure that it is connected

correctly by pulling the water supply hose

downwards.

5. Connect the other end of the water supply hose to the inlet

water valve at the rear of the washing machine. Screw the

hose clockwise all the way in.

setting up your washing

machine

Adaptor

Water supply

hose

1

2

5 mm

3

1

2

Water tap

WD8704CJ-02766A-04_EN.indd Sec4:14WD8704CJ-02766A-04_EN.indd Sec4:14 2011-03-17  6:27:162011-03-17  6:27:16

setting up your new washing machine _15

01 SETTING UP

6. Turn on the water supply and ensure that no water leaks

from the water valve, tap or adaptor. If there is a water

leaks, repeat the previous steps.

Do not use your washing machine if there is a water leak.

This may cause electric shock or injury.

• If the water tap has a screw type tap, connect the water

supply hose to the tap as shown.

Use the most conventional type of tap for the water supply. In case the tap is square or too

big, remove the spacing ring before inserting the tap into the adaptor.

✗

WARNING

WD8704CJ-02766A-04_EN.indd Sec4:15WD8704CJ-02766A-04_EN.indd Sec4:15 2011-03-17  6:27:172011-03-17  6:27:17

16_ setting up your new washing machine

Connecting the drain hose

The end of the drain hose can be positioned in three ways:

1. Over the edge of a wash basin: The drain hose must be placed at a height of between 60

and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure

the guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose

from moving.

2. ln a sink drain pipe branch: The drain pipe branch must be above the sink siphon so that

the end of the hose is at least 60 cm above the ground.

3. ln a drain pipe: We recommend using a 65 cm high vertical pipe; it must be no shorter than

60 cm and no longer than 90 cm.

The standpipe drain requires;

• minimum diameter 5 cm.

• minimum carry-away capacity 60 liter per minute.

STEP 5

Powering your washing machine

Plug the power cord into a wall sockets, a 230 volt 50 Hz approved electrical outlet protected by

a 15-amp fuse or comparable circuit breaker. (For more information on electrical and grounding

requirements, see page 10.)

setting up your washing

machine

Drain hose

Hose guide

60 ~ 90 cm

WD8704CJ-02766A-04_EN.indd Sec4:16WD8704CJ-02766A-04_EN.indd Sec4:16 2011-03-17  6:27:172011-03-17  6:27:17

washing a load of laundry _17

02 WASHING A LOAD OF LAUNDRY

washing a load of laundry

With your new Samsung washing machine, the hardest part of doing laundry will be

deciding which load to wash ﬁ rst.

WASHING FOR THE FIRST TIME

Before washing laundry for the ﬁ rst time, you must run a complete empty cycle (i.e. no laundry).

1. Press the Power button.

2. Add a little detergent to the detergent compartment

in

the detergent drawer.

3. Turn on the water supply to the washing machine.

4. Press the Start/Pause button.

This will remove any water that might be left over in the

machine from the manufacturer’s test run.

Compartment : Detergent for prewash, or starch.

Compartment : Detergent for the main wash, water softener, pre-soaking agent, bleach and

stain removal product.

Compartment : Additives, e.g. fabric softener or former (ﬁ ll no higher than lower edge (MAX)

of “A”)

BASIC INSTRUCTIONS

1. Load your laundry into the washing machine.

Do not overload the washing machine. To determine the load capacity for each type of

laundry, refer to the chart on page 24.

• Make sure that laundry is not caught in the door, as this may cause a water leak.

• Washing detergent may remain in the front rubber part of the washer after a wash cycle.

Remove any remaining detergent, as they may cause a water leak.

• Do not wash water-proofed items.

2. Close the door until it latches.

3. Turn the power on.

4. Add detergent and additives to the dispenser drawer.

5. Select the appropriate cycle and options for the load.

The Wash Indicator light will illuminate and the estimated cycle time will appear in the display.

6. Press the Start/Pause button.

WARNING

WD8704CJ-02766A-04_EN.indd Sec5:17WD8704CJ-02766A-04_EN.indd Sec5:17 2011-03-17  6:27:182011-03-17  6:27:18

18_ washing a load of laundry

USING THE CONTROL PANEL

DIGITAL GRAPHIC

DISPLAY

Displays the remaining wash cycle time, all cycle information, and error

messages.

CYCLE SELECTOR

Select the tumble pattern and spin speed for the cycle.

For detailed information, refer to “Washing clothes using the cycle

selector”. (see page 22)

Cotton - For averagely or lightly soiled cottons, bed linen, table linen,

underwear, towels, shirts, etc.

Synthetics -

For averagely or lightly soiled blouses, shirts, etc., made of

polyester (diolen, trevira), polyamide (perlon, nylon) or other similar blends.

Denim - A higher water level in the main wash and extra rinse ensure

that no washing powder remains that may mark your clothing.

Sports Wear - Use for water-proofed or proofed garments to keep their

good looks and fresh feel.

Delicates - For sheer fabrics, brassieres, lingerie, dresses, shirts and

blouses. For best results, use liquid detergent.

Wool - Only for machine-washable wool. A load should be less than 2.0 kg.

•

The wool course washes the laundry using gentle cradling actions.

During the wash, the gentle cradling and soaking actions are

continued to protect the wool ﬁ bers from shrinkage / distortion and

for a super gentle clean. This stop operation is not a problem.

• Neutral detergent is recommended for wool course, for improved

washing results and for improved care of the wool ﬁ bers.

The wool wash cycle of this machine has been approved by Woolmark

for the washing of machine-washable Woolmark products provided that

the products are washed according to the instructions on the garment

label and those issued by the manufacturer of this washing machine,

M0509 (Certiﬁ cate Number issued by IWS NOM INEE Co., Ltd.)

Handwash -

A very light wash cycle as gentle as a hand wash.

Air Wash -

This course is useful for removing bad odors. Turning the Cycle

Selector cycles through the following operating modes.

(Deodorization  Sanitization)

• Deodorization - Reduces bad smells from the laundry

• Sanitization - Deodorize and sterilize the laundry by stronger air

wash action with higher temp.

Drying

- Select to dry laundry automatically by detecting the amount and

weight of the laundry.

Daily Wash - Use for everyday items such as underwear and shirts.

Quick 29’ - For lightly soiled garments that you require quickly.

washing a load of laundry

543

6 8 97 1110 121 2

1

2

WD8704CJ-02766A-04_EN.indd Sec5:18WD8704CJ-02766A-04_EN.indd Sec5:18 2011-03-17  6:27:202011-03-17  6:27:20

washing a load of laundry _19

02 WASHING A LOAD OF LAUNDRY

Spin - Performs an additional spin cycle to remove more water.

Rinse + Spin - Use for a load that needs rinsing only or to add rinse-

added fabric softener to a load.

Drain Only - Turn the Cycle Selector to the Spin position, press the

Spin button, and then press the Start/Pause button to drain the water.

PREWASH

SELECTION BUTTON

Press this button to select pre-wash. Pre-wash is only available with:

Cotton, Synthetics, Denim, Sports Wear, Daily Wash.

DELAY END

SELECTION BUTTON

Press this button repeatedly to cycle through the available Delay End

options (from 3 hours to 19 hours in one hour increments).

The hour displayed indicates the time when the wash cycle will be ﬁ nished.

TEMPERATURE

SELECTION BUTTON

Press this button repeatedly to cycle through the available water

temperature options: (Cold Water

, 30 ˚C, 40 ˚C , 60 ˚C and 95 ˚C).

RINSE SELECTION

BUTTON

Press this button to add additional rinse cycles. The maximum number

of rinse cycles is ﬁ ve.

SPIN SELECTION

BUTTON

Press the button repeatedly to cycle through the available speeds for the

spin cycle.

WD8704

, , 400, 800, 1200, 1400 rpm

WD8702

, , 400, 800, 1000, 1200 rpm

WD8700

, , 400, 600, 800, 1000 rpm

“No spin

” - The laundry remains in the drum and no spin cycle is

performed after the ﬁ nal drain.

“Rinse Hold ” -The laundry remains soaking in the ﬁ nal rinse water. Before

the laundry can be unloaded, either a Drain or Spin cycle must be performed.

DRYING BUTTON

Pressing the button cycles through the following options.

Cup Board



Low Temp



Iron



Time Dry (30min.



1:00min.



1:30min.



2:00min.



2:30min.



3:00min.



3:30min.



4:00min.



4:30min.)



Cup Board

“Cup Board ” - Use this cycle to dry loads such as cotton, underwear,

and linen.

“Low Temp ” - This cycle protect heat-sensitive items at a low drying

temperature.

“Iron ” - Finishes the dry cycle in a moist state appropriate for Ironing.

“Time Dry ” -Dry the laundry for the speciﬁ ed period of time.

• You must avoid washing laundry that may not be dried as it may

be deformed even at low temperatures.

• The Cup Board, Low Temp, Iron and Time Dry options detect

the weight of the laundry in order to display an accurate drying

time and dry them more completely.

• The drying conditions may differ depending on the type and the

amount of laundry.

INTENSIVE WASH

SELECTION BUTTON

Press this button when the laundry is heavily soiled and needs to be

washed intensively. The cycle time is increased for each cycle.

SILVER WASH

SELECTION BUTTON

Silver Wash water is supplied during the wash cycle as well as during

the last rinse cycle, removing bacteria as well as giving protection from

bacterial growth for up to one month.

START/PAUSE

SELECTION BUTTON

Press to pause and restart a cycle.

POWER BUTTON

Press it once to turn your washing machine on, press it again to turn your

washing machine off. If the washing machine is left on for more than 10

minutes without any buttons being touched, the power automatically turns off.

3

5

6

7

8

9

10

11

12

4

WD8704CJ-02766A-04_EN.indd Sec5:19WD8704CJ-02766A-04_EN.indd Sec5:19 2011-03-17  6:27:212011-03-17  6:27:21

20_ washing a load of laundry

Child lock

The Child Lock function allows you to lock the buttons so that the wash cycle you’ve chosen

can’t be changed.

Activating/Deactivating

If you want to activate or deactivate the Child Lock function,

press the Temp. and Rinse buttons at the same time for

3 seconds. “Child Lock ” will be lit when this feature is

activated.

When the Child Lock function is activated, only the

Power button works. The Child Lock function remains

on even after the power is turned on and off or after the

disconnecting and reconnecting the power cord.

Sound off

The Sound Off function can be selected during all courses. When this function is selected, sound

is turned off for all courses. Even if the power is turned on and off repeatedly, the setting is

retained.

Activating/Deactivating

If you want to activate or deactivate the Sound Off function,

press the Spin and Drying Mode buttons at the same time for

3 seconds. The “Sound Off ” will be lit when this feature is

activated.

Delay end

You can set the washing machine to ﬁ nish your wash automatically at a later time, choosing a

delay of between 3 to 19 hours (in 1 hour increments). The hour displayed indicates the time at

which the wash will be ﬁ nished.

1. Manually or automatically set your washing machine according to the type of laundry you are

washing.

2. Press the Delay End button repeatedly until the delay time is set.

3. Press the Start/Pause button. The “Delay End ” indicator will be lit, and the clock will

begin counting down until it reaches the set time.

4. To cancel a Delay End function, press the Power button and then turn the washing machine

on again.

Drain Only Fuction

When you want just drain water from washing machine, follow directions below.

1. Press the Power button

2. Turn the Cycle Selector to the Spin positio.

3. Press the Spin button 1 times until rpm sign is off.

4. Then “1” shows up on time display in center.

5. Press the Start/Pause button.

washing a load of laundry

3 SEC.

WD8704CJ-02766A-04_EN.indd Sec5:20WD8704CJ-02766A-04_EN.indd Sec5:20 2011-03-17  6:27:232011-03-17  6:27:23

Page is loading ...

Samsung WD8704CJF/YAS User guide

Samsung WD8704CJF/YAS User guide

Related papers

Other documents