Samsung SCC-B2315P User manual

WDR DAY/NIGHT COLOR CAMERA

SCC-B2315(P)/SCC-B2015P

User Manual

ENG

FRE

SPA

JAP

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 1 2007-06-07 ｿﾀﾈﾄ 1:43:58

2 3

Safety Precautions

This symbol indicates high voltage is present inside. It is dangerous to make

any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and

maintenance has been included with this product.

To prevent damage which may result in ﬁre or electric shock hazard, do not expose

this appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation

sheet. Using any other adapter could cause ﬁre, electrical shock, or damage to

the product

2. Incorrectly connecting the power supply or replacing battery may cause

explosion, ﬁre, electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity

may cause abnormal heat generation or ﬁre.

4. Securely plug the power cord into the power receptacle. Insecure connection

may cause ﬁre.

5. When installing the camera, fasten it securely and ﬁrmly. A falling camera may

cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or

containers ﬁlled with water on top of the camera. Doing so may cause personal

injury due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause

ﬁre or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product. In

such case, immediately disconnect the power source and contact the service

center. Continued use in such a condition may cause ﬁre or electric shock.

9. If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. Doing so

may cause ﬁre or electric shock.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE REAR COVER. NO USER

SERVICEABLE PARTS INSIDE. REFER

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

The lighting ﬂash and

Arrowhead within

Triangle is a warning

sign alerting you of

dangerous voltage inside

the product.

The explanation point

within the triangle is a

warning sign alerting you

of important instructions

accompanying the

product.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 2 2007-06-07 ｿﾀﾈﾄ 1:43:59

2 3

ENG

Safety Precautions

CAUTION

1. Do not drop objects on the product or apply strong shock to it. Keep away from a

location subject to excessive vibration or magnetic interference.

2. If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

3. Remove the power plug from the outlet when then there is a lightning. Neglecting

to do so may cause ﬁre or damage to the product.

4. Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

5. Install it in a place with good ventilation.

6. Avoid aiming the camera directly towards extremely bright objects such as sun,

as this may damage the CCD image sensor.

7. Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled

with liquids, such as vases, shall be placed on the apparatus.

8. The Mains plug is used as a disconnect device and shall stay readily operable at

any time.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including interference that

may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian interference-

Causing Equipment Regulations of ICES-003.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 3 2007-06-07 ｿﾀﾈﾄ 1:43:59

4 5

Important Safety Instructions

1. Read Instructions – All the safety and operating instructions should be read

before the product is operated.

2. Retain Instructions – The safety and operating instructions should be retained

for future reference.

3. Heed Warnings – All warnings on the product and in the operating instructions

should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments – Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water – for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a

swimming pool; and the like.

8. Accessories – Do not place this product on an unstable cart, stand, tripod,

bracket, or table. The product may fall, causing serious injury to a child or

adult, and serious damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold with the product.

Any mounting of the product should follow the manufacturer’s instructions, and

should use a mounting accessory recommended by the manufacturer.

9. A product and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to

ensure reliable operation of the product and to protect it from overheating, and

these openings must not be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or other similar surface. This

product should not be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s instructions have

been adhered to.

11. Power Sources – This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of the type of power

supply to your home, consult your product dealer or local power company. For

products intended to operate from battery power, or other sources, refer to the

operating instructions.

12. Grounding or Polarization – This product may be equipped with a polarized

alternating-current line plug (a plug having one blade wider than the other). This

plug will ﬁt into the power outlet only one way. This is a safety feature. If you are

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 4 2007-06-07 ｿﾀﾈﾄ 1:43:59

4 5

ENG

unable to insert the plug fully into the outlet, try reversing the plug. If the plug

should still fail to ﬁt, contact your electrician to replace your obsolete outlet. Do

not defeat the safety purpose of the polarized plug. Alternate Warnings – This

product is equipped with a three-wire grounding-type plug, a plug having a third

(grounding) pin. This plug will only ﬁt into a grounding-type power outlet. This is

a safety feature. If you are unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not defeat the safety purpose of

the grounding-type plug.

13. Power-Cord Protection – Power-supply cords should be routed so that they are

not likely to be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14. Protective Attachment Plug – The product is equipped with an attachment plug

having overload protection. This is a safety feature. See Instruction Manual

for replacement or resetting of protective device. If replacement of the plug is

required, be sure the service technician has used a replacement plug speciﬁed

by the manufacturer that has the same overload protection as the original plug.

15. Outdoor Antenna Grounding – If an outside antenna or cable system is

connected to the product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information

with regard to proper grounding of the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding electrodes,

andrequirements for the grounding electrode.

16) Lightning – For added protection for this product during a lightning storm, or

when it is left unattended and unused for long periods of time, unplug it from

the wall outlet and disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line surges.

GROUND

CLAMP

ANTENNA LEAD

IN WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION S10-20)

GROUNDING CONDUCTORS

(NEC SECTION S10-21)

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND CLAMPS

ELECTRIC

SERVICE

EQUIPMENT

NEC - NATIONAL ELECTRICAL CODE

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 5 2007-06-07 ｿﾀﾈﾄ 1:44:21

6 7

17) Power Lines – An outside antenna system should not be located in the vicinity

of overhead power lines or other electric light or power circuits, or where it can

fall into such power lines or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such power lines or circuits

as contact with them might be fatal.

18) Overloading – Do not overload wall outlets, extension cords, or integral

convenience receptacles as this can result in a risk of ﬁre or electric shock.

19) Object and Liquid Entry – Never push objects of any kind into this product

through openings as they may touch dangerous voltage points or short-out parts

that could result in a ﬁre or electric hock. Never spill liquid of any kind on the

product.

20) Servicing – Do not attempt to service this product yourself as opening or

removing covers may expose you to dangerous voltage or other hazards. Refer

all servicing to qualiﬁed service personnel.

21) Damage Requiring Service – Unplug this product from the wall outlet and refer

servicing to qualiﬁed service personnel under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in damage

and will often require extensive work by a qualiﬁed technician to restore the

product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance – this indicates a

need for service.

22) Replacement Parts – When replacement parts are required, be sure the service

technician has used replacement parts speciﬁed by the manufacturer or have

the same characteristics as the original part. Unauthorized substitutions may

result in ﬁre, electric shock, or other hazards.

23) Safety Check – Upon completion of any service or repairs to this product, ask the

service technician to perform safety checks to determine that the product is in

proper operating condition.

24) Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling

only as recommended by the manufacturer.

25) Heat – The product should be situated away from heat sources such as radiators,

heat registers, stoves, or other products (including ampliﬁers) that produce heat.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled

with liquids, such as vases, shall be placed on the apparatus

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 6 2007-06-07 ｿﾀﾈﾄ 1:44:21

6 7

ENG

Contents

Safety Precautions ...... 2

Important Safety

Instructions ..................... 4

Contents ........................... 7

Overview ........................... 8

Special Features ........... 9

Part Names and

Functions ......................... 10

Side View ......................... 10

Rear Panel ....................... 12

Installation ....................... 15

Before Installation ......... 15

Checking the contents

of the package ..................

15

Things to keep in mind during

installation and use .............15

Connecting the Auto Iris

Lens Connector ................

16

Installing the Camera ... 17

Mounting the lens .............

17

Setting the ALC lens

selection switch ................

18

Adjusting the back focus .... 18

Connecting cables and

checking operation ...........

19

Camera Setup ................ 21

CAMERA ID ........................

22

IRIS ...................................... 22

WDR... ............................. 22

ALC... ............................... 23

ELC... ............................... 24

SHUTTER ......................... 24

AGC ................................... 25

MOTION ............................ 26

MOTION DET ................... 26

DAY/NIGHT ...................... 28

DAY... ...............................

29

NIGHT... ...........................

30

AUTO... ............................

30

EXT .................................. 31

WHITE BAL ...................... 31

PRIVACY ........................... 32

SPECIAL ........................... 33

LANGUAGE ..................... 33

V-SYNC ............................

33

DIGITAL ZOOM ...............

34

VIDEO SET ......................

34

DNR ................................. 35

FLICKERLESS ................. 35

SYSTEM INFO ................

36

RS-485 ............................... 36

EXIT ................................... 37

Product

Specifications ................ 38

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 7 2007-06-07 ｿﾀﾈﾄ 1:44:22

8 9

Overview

This enriched WDR (Wide Dynamic Range) Day/Night camera can

clearly implement both dark and bright parts on the screen with the

dual shutter.

When a bright object such as window occupies a part of the screen, it

appears white in conventional cameras. But using the state-of-the-art

WDR function that this camera provides, you can see the clear image.

This Day/Night camera activates the color mode when in the

illumination over the normal value. Otherwise it activates B/W (Black/

White) mode by removing the IR cut function, which can improve the

sensitivity for identifying objects even in a dark area.

It also incorporated the low speed shutter and Sens Up (Uses the

field accumulation method) functions to enhance the low illumination

feature.

This camera can be mainly used in the dark places such as

basement parking lots under comparatively low illumination. In

daytime, it displays the color screen with a horizontal resolution of

540 lines but at night, it uses the Day/Night feature along with the

Sens Up function to identify objects in a dark area. You can also

connect the infrared ray emission equipment to this camera.

DAY/NIGHT

This function can make the IR Cut filtering function inactive under

the illumination below the normal value.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 8 2007-06-07 ｿﾀﾈﾄ 1:44:22

8 9

ENG

Special Features

High Sensitivity

It implements images of high sensitivity using the up-to-date Super-

HAD P/S CCD.

WDR

The WDR function of this camera is the state-of-the-art technology

that can effectively enlarge the range for screen gain. It is mainly

used for taking photos for window scenes inside a building. Using

this technology, you can clearly see both indoor and outdoor

images, and can enjoy the excellent picture quality, which is

enabled by automatically adjusting the WDR level.

Low Illumination

It uses the digital signal technologies such as low illumination and

Day/Night functions that make your camera identify objects even in

the worst environment.

Superior Backlight Adjustment

When an object has a bright illumination or sunlight behind it, this

camera automatically improves the shaded object picture quality.

Digital Power Synchronization

The full digital Line Lock function directly adjusts the vertical

camera synchronization to enhance the operationability and

reliability of this camera.

High Resolution

This camera has realized high resolution of 540 lines using the

top-notch full digital image processing and special algorithm

technologies.

Output Signal Setting

You can set the following Video output signals: Image reversion

(Horizontal, Vertical, or both), Privacy, Horizontal/Vertical profiling,

and digital zooming.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 9 2007-06-07 ｿﾀﾈﾄ 1:44:22

10 11

Part Names and Functions

❚

Side View

1 Auto Iris Lens Connector

This groove is used for screwing the mount adapter, a part of the

bracket where the camera will be installed.

2 Mount Adapter Fixing Grooves

These grooves are used when fixing screws of the mount

adapter connected to the bracket when installing the camera on it.

3 Back Focus Control Bar

You can adjust the back focus by moving it up and down.

4 Automatic Shutter Lens Control Cable

This cable transmits the power and signals from the camera for

controlling the lens shutter.

4

Automatic Shutter

Lens Control Cable

5

ALC Lens

Selection Switch

1 Auto Iris Lens

Connector

2 Mount Adapter

Fixing Grooves

3 Back Focus

Control Bar

Camera Lens

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 10 2007-06-07 ｿﾀﾈﾄ 1:44:23

10 11

ENG

5 ALC Lens Selection Switch

This switch is used to select the type of the Auto Iris lens for

use. After this setting, you have to also set the lens type in the

Setup menu (In ALC… and WDR… submenus of IRIS).



DC: When the Auto Iris lens is installed for DC control

signals, set the switch to “DC.”



VIDEO: When the Auto Iris lens is installed for Video

control signals, set the switch to “VIDEO.”

Auto Iris Lens (Optional)

This lens is installed on this camera.

Note

When the camera lens becomes dirty, softly clean it with a lens

tissue or a cloth soaked in pure ethanol.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 11 2007-06-07 ｿﾀﾈﾄ 1:44:23

12 13

❚

Rear Panel

AC24/DC12V(SCC-B2315, B2315P)

AC220V~240V(SCC-B2015P)

1

5

2

3

4

1

2

3

4

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 12 2007-06-07 ｿﾀﾈﾄ 1:44:23

12 13

ENG

1 Input/Output Connector

This connector has input and output jacks for RS-485 control

signals, Day & Night switching, and alarm output signals.

No

.

Function Description

1 RS-485 DATA+ Jack for connection to RS-485 DATA+

signal line

.

2 RS-485 DATA- Jack for connection to RS-485 DATA-

signal line.

3 ALARM OUT Alarm out jack for motion detection

.

(Open Collector, On Gnd)

4 GROUND Grounding jack.

5 DC +5V Power supply jack for RS-485 JIG. Use

within typical DC +5V 100mA

6 EXTERNAL

SENSOR

Input jack for Day & Night conversion.

High (DC +3V~+5V): Day mode

Low (0V): Night mode

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 13 2007-06-07 ｿﾀﾈﾄ 1:44:24

14 15

2 Setup Switch

This switch is used to set the function or property. When this

switch is pressed for at least 2 seconds, the Setup menu

appears.



[Left/Right] movement or changing the displayed value:

By pressing this switch left or right, you can move left or

right on the menu or change the displayed value.



[Up/Down] movement: By pressing this switch up or

down, you can move up or down on the menu.



Setting: When you press this switch in the menu, the

selected value or function is confirmed. To enter a

submenu, press this button.

3 Power Display LED

When the power is normally connected, the red LED lights.

4 Video OUT Jack

This is connected to the Video Input jack of the monitor and it

outputs the Video signals.

5 Power Connection Jack

This is connected to the Power cable.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 14 2007-06-07 ｿﾀﾈﾄ 1:44:24

14 15

ENG

Installation

❚

Before Installation

Checking the contents of the package

Make sure that the following items are included in the package.

Things to keep in mind during installation and use



Do not disassemble the camera on your own.



Always be careful when handling the camera. Do not

strike the camera by your fists or shake it. Please be

careful not to be careless when storing and operating it.



Do not place or operate the camera in any wet

environment such as rain or wet surfaces.



Do not clean the camera with rough sandpaper. Please

always use a dry cloth when cleaning it.



Put the camera in a cool area free from direct sunlight.

Otherwise, the camera may be damaged.

Camera Camera Holder(Mount)

C Mount Adapter

Auto Iris

Lens Connector

User's Manual

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 15 2007-06-07 ｿﾀﾈﾄ 1:44:25

16 17

Connecting the Auto Iris Lens Connector

The Auto Iris Lens Connector that is provided with your camera

consists of the following parts:

Connect each uncovered shutter control cables to the Auto Iris Lens

Connector as the following:

Pin No. DC Control Type Video Control Type

1 Damp(-) Power (+12V)

2 Damp(+) Not applicable

3 Drive(+) Video Signal

4 Drive(-) Ground

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 16 2007-06-07 ｿﾀﾈﾄ 1:44:26

16 17

ENG

❚

Installing the Camera

Mounting the lens

When using the CS lens

Mount the CS lens by rotating it clockwise as shown in the picture:

When using the C lens

After mounting the C-mount adapter by rotating it clockwise, turn the

C lens clockwise until it is ﬁxed as shown in the picture.

CS lens

C lens

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 17 2007-06-07 ｿﾀﾈﾄ 1:44:27

18 19

Setting the ALC lens selection switch

You can set the lens selection switch located on the side of the camera

according to the lens type. When the mounted lens is an auto Iris lens

of DC control type, set the switch to “DC.” When the mounted lens is

an auto Iris lens of Video control type, set the switch to “VIDEO.”

N

Adjusting the back focus

The back focus of the camera is adjusted at the factory before delivery but

some lenses can be out of focus depending on the lens type. In this case,

you have to adjust the back focus. The following describes how to adjust

the back focus of the lenses.

In case of the lens with no zooming function

① After exposing the camera to an object with high resolution (like

a dart-patterned image) at a distance of more than 10m, set the

lens focus ring to infinite (∞).

➁ Adjust the Back Focus Control Bar until the object is of best quality.

➂ Fix the screw of the Back Focus Control Bar.

In case of the lens with zooming function

① After exposing the camera to an object with high resolution (like

a dart-patterned image) at a distance of 3 to 5m, fully rotate the

lens zoom to the TELE direction. Then adjust the lens focus ring

until the object is of best quality.

➁ Fully rotate the lens zoom to the WIDE direction and adjust the

Back Focus Control Bar until the object is of best quality.

➂ Repeat step 1 and 2 two or three times until the focuses of Zoom

TELE and Zoom WIDE are clear enough.

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 18 2007-06-07 ｿﾀﾈﾄ 1:44:27

18 19

ENG

Connecting cables and checking operation

1. Connect one end of the BNC cable to the VIDEO OUT jack on

the rear of the camera.

2. Connect another end of the BNC cable to the VIDEO IN jack on

the monitor.

N

BNC cable

Video Out Terminal

Video In Terminal of

Monitor Rear Surface

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 19 2007-06-07 ｿﾀﾈﾄ 1:44:28

20 21

3. Finally connect the power adapter to the camera. You can

connect 2 lines of the power adapter to the camera using the

Slot Head screwdriver as shown in the picture.

(GND: cable with the white stripe line

)

Note

Connect any power source of AC 24V and DC 12V irrespective

of polarity.

N

SCC-B2315_Eng_ｹﾌﾁﾖ.indd 20 2007-06-07 ｿﾀﾈﾄ 1:44:29

Page is loading ...

Samsung SCC-B2315P User manual

Samsung SCC-B2315P User manual

in other languages

Related papers

Other documents