i3 International i3B261 User manual

Brand: i3 International

Model: i3B261

Category: Security cameras

Type: User manual

i3B261

Colour Camera User Guide

WARNING:

Before attempting to connect or operate this product, read these instructions carefully.

Save this manual for future use.

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera.

Refer servicing to qualified personnel only.

CONTENTS

PRECAUTIONS

NOTES OF USE

CEILING MOUNT I

NSTALLATION

WALL MOUNT I

NSTALLATION

SPECIFICATIONS

PRECAUTIONS

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference, in which case users will be required to correct the

interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables

when connecting to computer or peripheral devices. Any changes

or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on top of the unit. It is

recommended that you note the serial number of this unit in the space

provided and retain this book as a permanent record of your purchase to

aid identication in the event of theft.

Model No.

Serial No.

Date of Purchase:

Grounding

This camera must be grounded. Follow the wire Colour code below:

Green/Yellow - Ground

Blue - Neutral

Brown - Positive

DVR

SYSTEM CONNECTION

Basic System Connection

Extended System Connection

TO AVOID THE RISK OF ELECTRIC SHOCK, PREVENT POWER CABLES FROM TOUCHING.

NOTES OF USE

Location and Function of Parts

1. Lens Mount (CS Mount): For installation of CS Mount lenses only.

2. Tripod Stand

: Allows mounting the camera onto a camera tripod.

3. Exposure Control

: Auto IRIS mode (two types of lens are appropriate for

this function).

- DC IRIS Lens

: Set the IRIS slide switch to the DC position and adjust the

LEVEL control on the side panel to obtain a clear picture.

- Video IRIS Lens

: Set the IRIS slide switch to the VIDEO position and adjust

the LEVEL and ALC controls on the lens to obtain a clear picture.

Automatic Electronic Shutter (AES)

: Set the IRIS slide switch to the AES

position to automatically adjust shutter speed according to the subjects

brightness.

4. V-phase Adjustment

: When using two cameras or more, the image on the

monitor may roll vertically when switching sources. This rolling can be

minimized by adjusting this controller.

5. DC IRIS Level Adjustment

: Use to compensate for the Iris Level of a

DC-type auto-iris lens. Turn counterclockwise towards L (low)/ clockwise

towards H (high) to make the picture appear darker/brighter.

6. Back-Focus Adjustment:

6A. Back Focus Screw:

Loosen the back focus screw before using focus

adjustment. Tighten after the desired focus is achieved to maintain setting.

6B. Focus Adjustment:

Adjust focus adjustment dial to obtain correct back-

focus (applies to CS mount lenses).

7. DIP Switch:

Function adjustment. (For further instructions see pp.4-6)

8. Video Output Terminal (BNC):

Connect external (“spot”) monitor to assist

adjustment of camera during installation.

9. Forced to BW external control terminal:

The camera will be forced to BW

mode with external contact.

NOTES OF USE

Dip Switch Panel

Side panel of the camera contains the Dip Switch panel with 12 dip switches.

Function of each dip switch is shown in the table below.

Dip Switch Name Dip Switch Function

N-AGC / S-AGC Auto gain control (normal AGC= 24 dB / super AGC = 30

dB)

BLC OFF / ON Back light compensation (On / Off)

L-LOCK / INT Sync system (Line-lock / Internal)

SOFT / SHARP Picture sharpness (Soft / Sharp)

ATW1 / ATW2 Auto white balance (ATW1 / ATW2)

CL / AUTO ICR mechanism (Colour / Auto)

AES / AI Exposure control (On / Off)

IR-OFF / IR-ON IR lamp (On / Off)

MES Manual shutter ranged from 1/50 (1/60) to 1/100k

NOTES OF USE

Dip Switch Function Description

1. Auto Gain Control (N-AGC / S-AGC)

N-AGC (Normal): Standard position, GAIN = 24dB.

S-AGC (Super): High-sensitivity position, GAIN = 30dB.

2. Back Light Compensation (ON / OFF)

ON: The BLC function is on

OFF: The BLC function is off.

3. SYNC System (L-LOCK/ INT)

L-LOCK: The camera is in the Line-lock mode. Adjust degrees by with

V-PHASE control on the side panel.

INT: The camera is in the internal SYNC mode.

4. Picture sharpness (SOFT / SHARP)

Picture sharpness selection.

5. Auto White Balance (ATW1 /ATW2)

TTL auto trace white balance algorithm is designed to implement a

perfect colour reproduction.

ATW1: Colour temperature range: 2500oK~6000oK.

ATW2: Colour temperature range: 2500oK~9500oK.

6. ICR Mechanism (CL / AUTO)

Choose the Day / Night mode by setting the dip switch to Auto or Colour

position.

Colour: The camera will remain in Colour mode.

Auto: The camera will automatically switch between Colour or B/W modes

according to the brightness of the scene being shot.

Congure a switchover point from Colour to B/W mode by selecting HIGH,

MID or LOW with a slide switch.

LOW: The switchover point of brightness from Colour to B/W is 1 lux (~ 10S)

MID: The switchover point of brightness from Colour to B/W is 2 lux (~ 10S)

HIGH: The switchover point of brightness from Colour to B/W is 3 lux (~ 10S)

The switch-over point of brightness from B/W to Colour mode is 8 lux (~ 10S)

7. Exposure Control (AES / AI)

ON: Auto electronic mode(AES)

The shutter speed varies from 1/50(60) sec to 1/100,000 sec depending on

the environmental conditions.

OFF: Auto IRIS mode(AI). Note: This function applies to DC lenses only.

After the AES dip switch is set to OFF position, adjust the LEVEL pot on the

back panel of the camera to get a clear picture.

8. IR Lamp (IR ON / IR OFF)

Using switch to select ON or OFF.

The environment with extra IR lights may cause issues for the ICR lter,

which can be resolved by turning this function ON.

9. Manual Shutter Control (Pins 9~12)

Follow the table below to manually congure shutter speed with the

dip switches #9-12.

Pin #

Shutter Speed

1/50

(1/60)*

1/120

(1/100)

1/250 1/500 1/1000 1/2000 1/4000 1/10000 1/100000

Pin 9

0 0 0 0 0 0 0 0 1

Pin 10

0 0 0 0 1 1 1 1 0

Pin 11

0 0 1 1 0 0 1 1 0

Pin 12

0 1 0 1 0 1 0 1 0

* factory default: 1/50 (1/60)

0: Down; 1: Up

IRIS Pin Connections

NOTES OF USE

AI AI AMP

1 +12V DAMP -(y)

2 NC DAMP +(r)

3 VIDEO DRIVER +(wh)

4 GND DRIVER -(g)

SPECIFICATIONS

Camera

Signal system NTSC PAL

Scanning system 2:1 Interlace

Sync system Internal / Line lock

Scanning frequency (H) 15.734 KHz 15.625 KHz

Scanning frequency (V) 59.94 Hz 50 Hz

Day & Night mode Auto / Manual / BW

Imaging area 4.9 mm x 3.7 mm

Image sensor Pixim Orca Sensor with Digital Pixel System ® technology

Horizontal resolution Day(Colour): 540TVL / Night(B/W): 600TVL

Effective pixels (HxV) 768 x 494 752 x 582

Lens mount CS

Gain control Auto (Normal/Super)

Min. illumination Day mode: 0.01 lux(F1.2, AGC on, 10 IRE); 0.2lux (F1.2, AGC on, 50 IRE)

Night mode: 0.003 lux(F1.2, AGC on, 10 IRE); 0.01lux (F1.2, AGC on, 50 IRE)

BLC ON/OFF

Day/Night mode picture Auto / Color / Forced BW

Iris Control Video / DC drive

White balance ATW1 / ATW2

S/N ratio > 50dB (AGC off)

View angle Wide=129.01 °(D) , 100.8°(H) , 73.3°(V), Tele= 34.32°(D) , 27.39°(H) ,

20.45°(V)

Video output 1Vpp composite output, 75 ohm

Gamma correction 0.45

Weight 500g approx. (1.10 lb)

Dimensions 50mm x 62mm x 126mm (1.96” x 2.44” x 4.96”)

Environment

Operating temperature -10º ~ 50º C (14º~122º F)

Storage temperature -20ºC ~ 60ºC (-4º ~ 140º F)

Humidity 30% ~ 90% RH

Electrical

Power requirement 12 VDC/24 VAC ±10%, AC90~260V

Power consumption 7W (max.)

Electric shutter Auto 1/60 to 1/100,000sec. / manual

8 steps (1/60, 1/100, 1/250, 1/500,

1/1K, 1/2K, 1/4K, 1/10Ksec.)

Auto 1/50 to 1/100,000sec. / manual

8 steps (1/50, 1/120, 1/250, 1/500,

1/1K, 1/2K, 1/4K, 1/10Ksec.)

Warranty

Product warranty 3 years

i³ INTERNATIONAL INC.

1.866.840.0004

www.i3international.com

Canada 780 Birchmount Road,

Unit 16, Scarborough,

ON, M1K 5H4

U.S.A. 440 Lawrence Bell Drive,

Suite 16, Williamsville

NY, 14221

i3 International i3B261 User manual

Brand: i3 International

Model: i3B261

Category: Security cameras

Type: User manual

Download PDF

report

i3 International i3B261 User manual

i3 International i3B261 User manual

Related papers

Other documents