Bedienungshinweise. . . . . . . . . . . . . . . . . . . . . . S. 2
Bitte vor Inbetriebnahme des Gerätes lesen!
User Instructions. . . . . . . . . . . . . . . . . . . . . . . . p. 12
Please read the manual before using the equipment!
Mode d’emploi . . . . . . . . . . . . . . . . . . . . . . . . . . p. 22
Veuillez lire cette notice avant d’utiliser le système!
Istruzioni per l’uso. . . . . . . . . . . . . . . . . . . . . . . p. 32
Prima di utilizzare l’apparecchio, leggere il manuale!
Modo de empleo . . . . . . . . . . . . . . . . . . . . . . . . p. 42
Antes de utilizar el equipo, lea por favor el manual!
Instruções de uso . . . . . . . . . . . . . . . . . . . . . . . p. 52
Favor leia este manual antes de usar o equipamen
to!
compact
Page is loading ...
3
2 Beschreibung
Siehe Fig. 14.
2.3 Windschutz
(2965Z2001)
2.4 Empfohlenes
Zubehör
Siehe Fig. 9.
Siehe Fig. 10.
Siehe Fig. 11.
Siehe Fig. 12.
Siehe Fig. 13.
Siehe Tabelle 1.
CHM 21 (Best.-Nr. 2965Z0005): Hängemikrofon mit
Federklemme und 10 m langem Spezialkabel mit
XLR-Phantomspeiseadapter DPA. Nierenförmige
Richtcharakteristik.
Verwenden Sie immer den mitgelieferten Windschutz
(außer der Windschutz würde optisch stören). Er schützt
das Mikrofon vor Staub und Feuchtigkeit und unterdrückt
Pop- und Windgeräusche weitgehend.
Batteriespeisegerät B 18 für alle Discreet Acoustics
Compact Mikrofone
Netzgeräte N 62 E, N 66 E für alle Discreet Acoustics
Compact Mikrofone
Montagesockel PS3 F-Lock für alle Discreet Acoustics
Compact Schwanenhalsmikrofone (nicht für CHM 21)
Elastische Halterung H 500 für alle Discreet Acoustics
Compact Schwanenhalsmikrofone (nicht für CHM 21)
Elastische Halterung H 600 für alle Discreet Acoustics
Compact Schwanenhalsmikrofone (nicht für CHM 21)
Stativanschluss SA 60 für alle Discreet Acoustics
Compact Schwanenhalsmikrofone (nicht für CHM 21)
Tischstative ST 1, ST 45 für alle Discreet Acoustics
Compact Schwanenhalsmikrofone (nicht für CHM 21)
Bitte beachten Sie, dass der Aufnahmewinkel sowohl den
maximalen Besprechungsabstand als auch die
abzunehmende Fläche beeinflusst. Je kleiner der
Aufnahmewinkel (Hyperniere), desto größer die maximale
Distanz zwischen Sprecher und Mikrofon, desto kleiner
aber die abzunehmende Fläche.
Ob Sie ein Nieren- oder Hypernierenmikrofon einsetzen,
hängt daher von der jeweiligen Anwendungssituation ab.
3 Mikrofonanwendungen
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
11
Frequenzgang &
Polardiagramm
CGN 321 E
Frequenzgang &
Polardiagramm
CGN 323 E
Frequenzgang &
Polardiagramm
CGN 521 E
Frequenzgang &
Polardiagramm
CGN 523 E
Frequenzgang &
Polardiagramm
CHM 21
5 Technische Daten
12
2.1 Introduction
2.2 Microphones
Refer to figs. 9 to 14.
1. Do not spill any liquids on the equipment and do not
drop any objects through the ventilation slots in the
equipment.
2. Do not place the equipment near heat sources such
as radiators, heating ducts, or amplifiers, etc. and do
not expose it to direct sunlight, excessive dust, mois-
ture, rain, mechanical vibrations, or shock.
3. The packaging of the equipment is recyclabe. To dis-
pose of the packaging, make sure to use a collec-
tion/recycling system provided for that purpose and
observe local legislation relating to waste disposal
and recycling.
Thank you for purchasing a Discreet Acoustics
module. The Discreet Acoustics Compact Series com-
prises four gooseneck microphones, one flown micro-
phone, and dedicated accessories for every application
and every type of venue.
CGN 321 E (order no. 2965Z0001): 380-mm (15-in.) car-
dioid gooseneck microphone with integrated DPA XLR
phantom power adapter and external foam windscreen.
CGN 323 E (order no. 2965Z0002): 380-mm (15-in.)
hypercardioid gooseneck microphone with integrated
DPA XLR phantom power adapter and external foam
windscreen.
CGN 521 E (order no. 2965Z0003): 576-mm (23-in.) car-
dioid gooseneck microphone with integrated DPA XLR
phantom power adapter and external foam windscreen.
CGN 323 E (order no. 2965Z0004): 576-mm (23-in.)
hypercardioid gooseneck microphone with integrated
DPA XLR phantom power adapter and external foam
windscreen.
CHM 21 (order no. 2965Z0005): cardioid flown micro-
phone with spring clamp and 10-m (33-ft.) special cable
with DPA XLR phantom power adapter.
1 Safety and Environment
2 Description
13
2 Description
2.3 Windscreen
(2965Z2001)
2.4 Optional
Accessories
Refer to fig. 9.
Refer to fig.10.
Refer to fig.11.
Refer to fig.12.
Refer to fig.13.
Refer to Table 1.
Always use the supplied windscreen (unless it would be
too visually obtrusive). It protects the microphone from
dust and moisture, and reduces pop and wind noise to a
minimum.
B 18 battery power supply for all Discreet Acoustics
Compact microphones.
N 62 E, N 66 E AC power supplies for all Discreet
Acoustics Compact microphones.
PS3 F-Lock panel mount socket for all Discreet
Acoustics Compact gooseneck microphones (not for
CHM 21).
H 500 shock mount for all Discreet Acoustics Compact
gooseneck microphones (not for CHM 21).
H 600 shock mount for all Discreet Acoustics Compact
gooseneck microphones (not for CHM 21).
SA 60 stand adapter for all Discreet Acoustics Compact
gooseneck microphones (not for CHM 21).
ST 1, ST 45 table stands for all Discreet Acoustics
Compact gooseneck microphones (not for CHM 21).
Note that both the maximum working distance and the
area covered by the microphone depend on the pickup
angle. The smaller the pickup angle (hypercardioid), the
longer the maximum distance between the talker and the
microphone and the smaller the area covered by the
microphone.
Whether a cardioid or hypercardioid capsule will give the
best results therefore depends on the specific application
situation).
3 Microphone Applications
14
3 Microphone Applications
4.1 Introduction
4.2 CGN .. E
Gooseneck
Microphones
Refer to figs. 9 and 12.
Note:
Refer to figs. 10 and 11.
All Discreet Acoustics Compact microphones are con-
denser microphones and therefore require a power supply
(phantom power). The microphones have been designed
for connection to microphone inputs with 9 to
52 V phantom power. To connect Discreet Acoustics
Compact microphones to inputs without phantom power,
refer to Section 4.4.
1. Use the optional PS 3 F-Lock panel mount socket to
install the microphone in a tabletop or an optional
SA 60 stand adapter to mount the microphone on a
floor or table stand.
For even better vibrational noise rejection, you can fix
the microphone to the tabletop with an optional H 500
or H 600 shock mount.
2. Use a shielded cable to connect the microphone to a
microphone input with phantom power.
Table 1: Microphone applications.
Microphone
CGN 321 E
CGN 323 E
CGN 521 E
CGN 523 E
CHM 21
Polar Pattern
Cardioid
Hypercardioid
Cardioid
Hypercardioid
Cardioid
Speaker position
Beinde the micro-
phone only
90° to 135° off
microphone axis
Behind the micro-
phone only
90° to 135° off
microphone
axis
Behind the micro-
phone only
Working
distance
30 to 60 cm*
(1 to 2 feet)
30 to 90 cm*
(1 to 3 feet)
30 to 60 cm*
(1 to 2 feet)
30 to 90 cm*
(1 to 3 feet)
1 to 3 m*
(3.5 to 10 feet)
Application
Sound system
Sound system
Sound system
Sound system
Sound system
4 Installation and Connection
* Depending upon Acoustic environment
4 Installation and Connection
15
4.3 CHM 21 Flown
Microphone
Important!
Fig. 1: Aligning the
microphone.
Refer to fig. 1.
Note:
3. If the phantom power on your mixing console is
switchable, switch the phantom power on. (Refer to
the instruction manual for your mixing console.)
The microphone is powered directly from the phan-
tom power source on the console.
1. Prior to installing the microphone, straighten the
cable by carefully pulling it through your fingers. Make
sure not to buckle or twist the cable. Let hang for 1 day to
untwist.
2. Fasten a hook to the ceiling, use an existing hook, or
stretch a fishing line across the hall.
3. Pass the cable through the hook or over the line so
that it will hang at the desired height.
Do not tie a knot into the cable to hang it on the
hook. This may cause the cable to twist and misalign
the microphone after a while.
5. Hold the cable with one hand and turn the micro-
phone carefully into the desired position.
• The cable on the CHM 21 will twist as the ambient
temperature changes, e.g., in the heat generated by
spotlights.
• The angle of twist depends both on the ambient tem-
perature and the cable length. The shorter the cable,
the smaller the amount of twist.
4 Installation and Connection
16
4.3.1 Stabilizing
the Microphone
4.3.2 Applications
Fig. 2: Theater stage
miking
Fig. 3: Miking up a
choir
• If you use spotlights, be sure to turn them on
before aligning the microphone.
• When you turn the spotlights off, the microphone will
rotate out of alignment. Upon turning the spotlights
back on, the microphone should rotate back into its
original position.
To stabilize the microphone,
1. Leave an appropriate length of fishing line through the
eyelet on the spring clamp of the CHM 21.
2. Fix the fishing line to two opposite walls so as to cre-
ate just enough downward pull to steady the micro-
phone laterally.
4 Installation and Connection
17
4.3.3 Audio
Connection
4.4 Connecting to
Inputs without
Phantom Power
4.4.1 Balanced
Inputs
Fig. 4: Input trans-
former with center
tap (ungrounded)
Fig. 5: Input trans-
former with no
center tap
(ungrounded)
1. Use a shielded balanced cable to connect the micro-
phone to a microphone input with phantom power.
2. If the phantom power on your mixing console is
switchable, switch the phantom power on. (Refer to
the instruction manual for your mixing console.)
The microphone is powered directly from the phan-
tom power source.
If your mixer has no phantom power, insert an external
phantom power supply between the DPA phantom power
adapter and mixer input. We recommend the optional
B 18, N 62 E, or N 66 E power supplies from AKG. Using
any power supplies not recommended by AKG may
damage your microphone and voids the warranty.
You may also consider having a qualified technician
retrofit a phantom power supply as per DIN 45596 to bal-
anced or unbalanced mixer inputs. The DIN 45596 stan-
dard specifies a positive voltage of 12, 24, or 48 V on the
audio lines versus the cable shield.
If your equipment inputs are grounded or transformer-
less, wire either capacitors or extra transformers into the
audio lines as shown in fig. 9 above in order to prevent
any current leakage into the input stage.
4 Installation and Connection
18
4.4.2 Unbalanced
Inputs
Fig. 6: Unbalanced
input stage
Table 2: Standard val-
ues for Rv and 2 x Rv
VDC Rv 2 x Rv*
12 V ±2 V 330 Ω 680 Ω
24 V ±4 V 680 Ω 1,200 Ω
48 V ±4 V 3,300 Ω 6,800 Ω
* In order to satisfy the DIN 45596 symmetry requirement,
make sure the actual values of the two resistors 2 x Rv
do not differ by more than 0.5%!
4 Installation and Connection
19
4.5 Bass Cut
Fig. 7: Fixing screw.
Refer to fig. 7.
Fig. 8: DPA circuit
board.
Refer to fig. 8.
The DPA phantom power adapter is equipped with a bass
cut filter to minimize low-frequency noise.
1. Unscrew the fixing screw on the microphone or DPA
phantom power adapter.
2. Pull the circuit board out of the case WITH CAUTION
– so as not to break the internal leads.
3. To acitvate the bass cut filter, plug the jumper J1 into
the central contact pair on the circuit board.
CHM 21
CGN ... E
20
5 Specifications
* re 1 V/Pa
This product conforms to EN 540082-1 provided it is connected to audio/power
supply equipment with a CE mark.
Microphone CGN 321 E CGN 323 E
CGN 521 E CGN 523 E CHM 21
Type Pre-polarized condenser microphone
Polar pattern Cardioid Hypercardioid Cardioid
Frequency range 70 to 18,000 Hz 50 to 19,000 Hz 70 to 18,000 Hz
Sensitivity 18 mV/Pa 12 mV/Pa 18 mV/Pa
-35 dBV* -38 dBV* -35 dBV*
Max. SPL for 1% THD 125 dB 125 dB 125 dB
Equivalent noise level <21 dB-A <21 dB-A <21 dB-A
Signal/noise ratio
(A-weighted.) >73 dB >73 dB >73 dB
Electrical impedance <600 Ω <600 Ω <600 Ω
Receommended
load impedance
>2000 Ω >2000 Ω >2000 Ω
Power requirement 9 to 52 V phantom power to DIN 45596
(DPA adapter integrated)
Current consumption <3 mA <3 mA <3 mA
Connector XLR-3 XLR-3 XLR-3
Finish matte dark gray matte dark gray matte dark gray
Size 13.5 x 380 mm 13.5 x 380 mm
(capsule dia. x length) (0.5 x 15 in.) (0.5 x 15 in.)
13.5 x 580 mm 13.5 x 580 mm 13.5 x 55 mm
(0.5 x 23 in.) (0.5 x 23 in.) (0.5 x 2.1 in.)
Net/shipping weight 160/480 g 160/480 g
(5.7/17 oz.) (5.7/17 oz.)
170/500 g 170/500 g 20/480 g
(6/17.7 oz.) (6/17.7 oz.) (0.7 x 17 oz.)
Order no. 2965Z0001 2965Z0002
2965Z0003 2965Z0004 2965Z0005
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
28
4 Montage et raccordement
4.4.2 Entrées asy-
métriques
Fig. 6: Etage d’entrée
asymétrique
Tableau 2: Valeurs
standard pour Rv
(ou 2 x Rv)
Si les entrées de la table de mixage sont mises à la terre
ou qu’on ne dispose pas de transformateurs d’entrée, il
est nécessaire d’insérer des condensateurs ou des trans-
formateurs supplémentaires dans les lignes audio pour
protéger l’étage d’entrée d’éventuels courants de fuite.
Vcc Rv 2 x Rv*
12 V ±2 V 330 Ω 680 Ω
24 V ±4 V 680 Ω 1,200 Ω
48 V ±4 V 3,300 Ω 6,800 Ω
* Pour respecter la symétrie, l’écart de tolérance des
résistances 2 x Rv ne devra pas dépasser 0,5%.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
48
4 Montaje y conexión
4.4.2 Entradas no
balanceadas
Fig. 6: Etapa de en-
trada no balanceada
Cuadro 2: Valores
normalizados para Rv
(o 2 x Rv)
Si las entradas de su pupitre mezclador tienen toma de tie-
rra o si no están incorporados transformadores de entrada,
Vd. tiene que incorporar condensadores o transformado-
res adicionales en las líneas audio para evitar perturbacio-
nes de la etapa de entrada por corrientes de fuga.
Vcc Rv 2 x Rv*
12 V ±2 V 330 Ω 680 Ω
24 V ±2 V 680 Ω 1200 Ω
48 V ±2 V 3300 Ω 6800 WΩ
* Por razones de simetría las resistencias 2 x Rv pueden
divergir como máximo en un 0,5 %.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
4 Montagem e ligação
58
4.4.2 Entradas
não-balanceadas
Fig 6: Etapa de entra-
da não
balanceada
Tabela 2: Valores-
padrão para Rv (2x
Rv respetivamente)
Se as entradas da mesa de mixagem estiverem ligadas à
terra ou não possuirem transformador de entrada, terá de
introduzir ou condensadores ou transformadores adicio-
nais nos condutores áudio, a fim de evitar a perturbação
da etapa de entrada por corrente de fuga.
Vcc Rv 2 x Rv*
12V ±2V 330 Ω 680 Ω
24V ±2V 680 Ω 1200 Ω
48V ±4V 3300 Ω 6800 Ω
* As resistências 2xRv só podem, por razões de simetria,
possuir uma tolerãncia máxima de 0,5 %
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
63
Fig. 14: CHM 21
Fig. 13: CGN 521 E
+ SA 60 + ST 45
Fig. 11: CGN 521 E
+ H 600
Printed in Austria on recycled paper. 12/03/9100 U 1063
Technische Änderungen vorbehalten. Specifications subject to change without notice. Ces caractéristiques sont susceptibles de modifications.
Ci riserviamo il diritto di effettuare modifiche tecniche. Nos reservamos el derecho de introducir modificaciones técnicas. Especificações sujeitas à mudanças sem aviso prévio.
Mikrofone · Kopfhörer · Drahtlosmikrofone · Drahtloskopfhörer · Kopfsprechgarnituren · Akustische Komponenten
Microphones · Headphones · Wireless Microphones · Wireless Headphones · Headsets · Electroacoustical Components
Microphones · Casques HiFi · Microphones sans fil · Casques sans fil · Micros-casques · Composants acoustiques
Microfoni · Cuffie HiFi · Microfoni senza filo · Cuffie senza filo · Cuffie-microfono · Componenti acustici
Micrófonos · Auriculares · Micrófonos inalámbricos · Auriculares inalámbricos · Auriculares con micrófono · Componentes acústicos
Microfones · Fones de ouvido · Microfones s/fios · Fones de ouvido s/fios · Microfones de cabeça · Componentes acústicos
AKG Acoustics GmbH
Lemböckgasse 21–25, P.O.B. 158, A-1230 Vienna/AUSTRIA, Tel: (+43 1) 86 654-0*, Fax: (+43 1) 86 654-7516,
www.akg.com, e-mail: [email protected], Hotline: (+43 676) 83200 888, [email protected]
AKG Acoustics GmbH
Bodenseestraße 228, D-81243 München/GERMANY, Tel: (+49 89) 87 16-0, Fax: (+49 89) 87 16-200,
www.akg-acoustics.de, e-mail: [email protected], Hotline: (+49 89) 87 16-22 50, [email protected]
AKG ACOUSTICS, U.S.
914 Airpark Center Drive, Nashville, TN 37217, U.S.A., Tel: (+1 615) 620-3800, Fax: (+1 615) 620-3875,
www.akgusa.com, e-mail: [email protected]
For other products and distributors worldwide see our website: www.akg.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
AKG CGN 523 E Owner's manual
- Category
- Microphones
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: AKG CGN 523 E Manuale del proprietario
- français: AKG CGN 523 E Le manuel du propriétaire
- español: AKG CGN 523 E El manual del propietario
- Deutsch: AKG CGN 523 E Bedienungsanleitung
- português: AKG CGN 523 E Manual do proprietário
Related papers
-
AKG Acoustics CGN 99 CS User manual
-
AKG Acoustics CK33 User manual
-
AKG C 562 CM Owner's manual
-
-
Lexicon D 88 S Owner's manual
-
-
-
AKG D112 MKII Quick User Manual
-
-
Other documents
-
-
-
AKG Acoustics C 4500 B-BC User manual
-
Marantz Phantom Pack User guide
-
M-Audio Nova User guide
-
-
Behringer C-2 Owner's manual
-
IMG STAGELINE ECMS-90 User manual
-
M-Audio Pulsar II User guide
-