Swann ads 440 User manual

Brand: Swann

Model: ads 440

Type: User manual

Wi-Fi Security Camera

INSTRUCTION MANUAL

Pan & Tilt

Limited Warranty Terms & Conditions

Swann Communications warrants this product against defects in workmanship and material for a period of one

(1) year from its original purchase date. You must present your receipt as proof of date of purchase for warranty

validation. Any unit which proves defective during the stated period will be repaired without charge for parts or

labour or replaced at the sole discretion of Swann. The end user is responsible for all freight charges incurred

to send the product to Swann’s repair centres. The end user is responsible for all shipping costs incurred when

shipping from and to any country other than the country of origin.

The warranty does not cover any incidental, accidental or consequential damages arising from the use of or the

inability to use this product. Any costs associated with the fitting or removal of this product by a tradesman or other

person or any other costs associated with its use are the responsibility of the end user. This warranty applies to the

original purchaser of the product only and is not transferable to any third party. Unauthorized end user or third

party modifications to any component or evidence of misuse or abuse of the device will render all warranties void.

By law some countries do not allow limitations on certain exclusions in this warranty. Where applicable by local

laws, regulations and legal rights will take precedence.

For Australia: Our goods come with guarantees which cannot be excluded under Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable

quality and the failure does not amount to major failure.

FCC Verification

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• These devices may not cause harmful interference, and

• These devices must accept any interference received, including interference that may cause undesired

operation.

Important Note:

All jurisdictions have specific laws and regulations relating to the use of cameras. Before using any camera for any

purpose, it is the buyer’s responsibility to be aware of all applicable laws and regulations that prohibit or limit the use

of cameras and to comply with the applicable laws and regulations.

WARNING

Modifications not approved by the party responsible for compliance could void user’s authority to

operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS

• Make sure product is fixed correctly and stable if fastened in place.

• Do not operate if wires and terminals are exposed.

Before You Begin

Contents

Quick Reference

Before You Begin ........................................................................................................... 1

Contents ......................................................................................................................... 2

Introduction ................................................................................................................... 3

Layout of the Camera ................................................................................................... 3

Connection Guide .......................................................................................................... 4

SwannEye Plus Software ............................................................................................. 5

SwannEye Plus Live View Interface ............................................................................ 6

Camera Wi-Fi Setup ..................................................................................................... 8

Camera Wi-Fi Settings ................................................................................................. 9

Have an iPhone or Android Smartphone? ............................................................... 10

SwannEye Plus App Camera Setup ........................................................................... 11

Using SwannEye Plus App ..........................................................................................12

Accessing the Camera via Web Browser ................................................................. 14

Setting up Email Alerts via Web Browser ................................................................ 15

Default Camera Username and Password Information

Username: admin

Password: 123456

Notice

The information printed in this instruction manual is correct at the time of publication.

As we’re constantly making improvements to our products, firmware, software and user

manuals, we reserve the right to change the information without prior notice.

Remember to check the Swann website for updates and more information:

www.swann.com

Introduction

Layout of the Camera

Infrared LEDs: Illuminates targeted

areas when in near-total darkness.

Illumination Sensor: Detects the amount

of incoming light and turns on the IR

LEDs for night vision when necessary.

Microphone: Allows the camera to hear

nearby sounds and stream them with

video.

Power LED: Solid red indicates camera

is powered.

Network LED: Blinks when there is

communication between the camera

and network.

DC In Power: To connect power adapter.

Antenna Connector: To attach Wi-Fi

antenna.

Reset Button: Press and hold for a few

seconds to reset all camera settings

back to the factory defaults.

Network (LAN) Port: To connect

Ethernet cable to a router for wired

connections.

Audio In: To connect an external

microphone.

Audio Out: To use the intercom function,

connect speakers to the audio output.

Using SwannEye Plus, you can talk to

your mobile device and your voice will be

heard on the speakers connected to the

camera.

Alarm I/O Block: For connecting

external alarms and sensors.

Congratulations on your purchase of this Swann Pan & Tilt

IP Camera! This camera is versatile, easy to set up and

packs some nifty features like built-in microphone for 2-way

conversations and infrared night vision. Best of all, it can

be totally wireless - if there’s a Wi-Fi network your camera

can connect to the Internet through, then just connect the

camera to power and you’re good to go.

4 5

11 12

Connection Guide

To install the camera, connect it to your router or network switch/hub using the included

Ethernet cable. The camera is also Wi-Fi capable - but because this is the first time you’re

setting it up, we recommend physically connecting it to your home network through the

Ethernet cable and configuring it properly before you go wireless.

2 Connect the power supply to

the camera’s DC In port and

plug the power adapter to an

electrical outlet.

3 Connect the camera’s

Network port to any

available port on your

wireless router using the

supplied Ethernet cable.

4 Make sure the computer that you

want to use to configure and/or

access the camera is connected to the

same router.

1 Screw the Wi-Fi antenna

onto the Gold connector on

the back of the camera.

SwannEye Plus Software

Included with the camera is the SwannEye Plus software for Windows.

SwannEye Plus is an easy to use software which enables you to set up and control the

camera that’s connected on your home network from your computer. In addition to watching

live video feeds from multiple cameras, SwannEye Plus also allows you to simultaneously

record and playback videos you have just taken while your current recordings continue

uninterrupted.

A mobile app version of this software is also available for Android and iPhone smartphones.

The SwannEye Plus app can be downloaded for free from the Apple App Store or Google Play

Store. See “Have an iPhone or Android Smartphone?” on page 10 for more details.

Installing SwannEye Plus on your Windows PC

Follow the instructions below to install SwannEye Plus onto your computer.

Windows Users

1 Insert the software CD into your PC’s optical disc tray and wait for the AutoPlay window

to appear.

2 When prompted, select AUTORUN and allow the installer menu to open. From here,

read the onscreen instructions for installing the software and opening the manuals.

If the AutoPlay window isn’t enabled on your system, you can access the optical disc

tray from “My Computer”, then select the amplayer file on the CD and run the installer

directly.

From the CD you can install the SwannEye Plus PC monitoring software to view and record

from your camera and numerous other functions.

SwannEye Plus Live View Interface

When you launch SwannEye Plus software, you will see the following screen:

The SwannEye Plus Live View interface allows you to monitor camera feeds from up to

sixteen (16) cameras at once (assuming sufficient bandwidth). From here, you are also

able to record videos, take snapshots, configure Wi-Fi settings, engage in 2-way audio

conversation remotely and do much more.

Many of the functions and buttons in the Live View interface are self-explanatory. In fact,

pointing the mouse cursor at a button will reveal a tool-tip telling you what the button does.

Adding to the Camera List

The camera contains a Unique IDentifier code that’s embedded on a QR sticker (it’s a

sticker with lots of little black squares that form a larger black and white square). The UID

helps you to connect your PC or SmartPhone to the camera in just a few simple steps using

Swann’s Peer-to-Peer (P2P) network technology. P2P cuts out all of the messy networking

stuff that you used to have to do to get connected!

Before you perform the following steps, look for the QR sticker on the bottom side of the

camera and write down the UID code:

1 Click the button. This displays the Add Device Information window.

2 Click Search. Your computer will scan for connected cameras and display them as a list.

3 Double-click the UID code that matches your camera. This populates the UID box at the

bottom of the window automatically.

At this point, you may want to write down your camera’s IP address as this will be helpful

when you want to access the camera using a web browser. See “Accessing the Camera

through a Browser” on page 14 for more details.

Camera List

Play/

Stop All

Cameras

Connection

status

Camera

Operation

Screen Modes

Configure cameras

Set recording

folder and

view images &

video clips

4 Click in the Device Name box and then enter a unique name for the camera. We suggest

calling it something that can help you identify it easily.

5 Click in the Device Password box, enter the default camera password (“123456”) and

then click Save. The camera you’ve just added will appear in the camera list in the Live

View interface. Since it’s the first camera added, it will occupy the number 1 row in the

list. If you add more cameras, these cameras will be listed in the order they are added.

6 Double-click on the camera name (no.1) to start watching live video on the

corresponding channel number (channel 1).

Here’s a quick summary of what you need to do:

SwannEye Plus Live View Interface

Double-click the newly

added camera to start

streaming live video

on the corresponding

channel.

Search for camera.

You can also open an

Internet browser and

enter the IP address of

the camera to access

the camera’s live view.

Name

camera.

Enter

default

password.

Save the information.

Double-click

the UID

matching

your camera.

So, you’ve got the camera installed and successfully accessed it via the network but you

don’t want that cable running down the hallway? Time to enjoy the flexibility of wireless.

Setting up the camera with your Wi-Fi network is easier than you might think!

Before starting, ensure the camera has the Wi-Fi antenna attached and is within range of your

wireless home network. Also, it’ll be good to have your network name and password ready.

Connecting to the Wi-Fi Network

1 On the Live View interface, select the camera that you want to access wirelessly and

then click the Camera Settings button. This displays the Edit Device Information

window.

2 Click Remote Settings. Wait a few seconds for your PC to establish connection with the

camera and display the Remote Settings window.

3 Click Manage WiFi Network. In the Manage WiFi Network window that appears,

you will see a list (WiFi SSID) of available wireless networks which the camera has

automatically detected. When you select a wireless network, you can see its encryption

type and signal strength.

4 In the list of available wireless networks (WiFi SSID), select a network, enter the Wi-Fi

password (also commonly known as network security key) and then click OK. If there’s

any other wireless networks in your area that you want the camera to connect to,

simply repeat steps 3 and 4.

Camera Wi-Fi Setup

Now unplug the camera from the router and enjoy the convenience of putting the camera

whereever you want (as long as it’s within range of your home Wi-Fi network!). Next, If

you have a smartphone, download the SwannEye Plus mobile app and start watching live

streaming video anywhere with your smartphone through Wi-Fi.

If your camera is experiencing constant dropouts, this could mean that it’s too far away from

your router. Check the Wi-Fi signal strength using the SwannEye Plus software or app. Low

signal strength can sometimes affect the performance of the camera. Try moving the camera

around to get an idea of the range of the wireless signal and the best place to use it. If that’s

not possible, you could consider buying and installing a Wi-Fi Range Extender in your home to

boost the Wi-Fi signal.

In the Remote Settings window, you can change the camera’s default password and

adjust various video settings for the camera. The settings here will affect the quality and

performance of the video stream when you view the camera wirelessly from the SwannEye

Plus software, app or web browser.

Device Password Settings: Here you can change the default camera password to something

of your choosing. Always choose a strong password (e.g., a mixture of uppercase/lowercase

letters and numbers) to help prevent unauthorized people from watching live video on your

camera. It is highly recommended that you change the password after installing the camera.

Keep your password somewhere safe. If you lose or forget your password, you will have to

“reset” your camera to its original factory configuration and set up your camera again.

Video Quality: How much information will be sent per-pixel. High quality settings look great,

but the bandwidth required to send the image will be much higher. This is also going to

depend on the speed of your network connection. Adjusting video quality to a lower setting

may produce a smoother looking image. Video quality setting also determines the resolution

of the video stream. The highest video quality (Max) will display video size at 640 x 480

resolution while the lowest video quality (Min) will display video size at 160 x 120 resolution.

Video Flip: You can choose to flip the video horizontally, vertically or both. This setting is

useful when the camera needs to be installed upside down. Default setting is Normal.

Environment Mode: Change the light environment setting of the camera. Some devices

(such as TV screens and fluorescent lights) will flicker if this is not set correctly. For USA and

Canada, set this to Indoor 60Hz. For Australia and the UK, set this to Indoor 50Hz. Outdoor

and Night modes are also available.

Camera Settings

Have an iPhone or Android Smartphone?

Then head to the respective Apple App Store or Google Play, download the SwannEye Plus

app for free and start watching live camera videos from your mobile device.

Please note, make sure you download the PLUS version of the SwannEye app! The following

images are captured from the iOS version of the mobile app. You may notice a slight layout

difference in the Android version of the app but otherwise they both behave in the same manner.

Installing the SwannEye Plus Smartphone App

iOS:

1 Tap App Store.

2 Tap and find SwannEye Plus.

3 Tap to download.

Android:

1 Tap > Play Store.

2 Tap and find SwannEye Plus.

3 Tap to download.

Running the App

Locate the SwannEye Plus app and tap the icon to run. The app will load and take you

directly to the main screen.

App Interface

Camera: Shows a list of cameras registered with

the app. The is also the first screen that appears

each time you run the app.

Add Camera: Here you can register cameras with

your app.

Info: Displays information about the app.

Camera List area: This is where all your registered

cameras are listed.

Find: Search for a specific camera by name. Useful

when you have multiple cameras registered with

the app.

Edit: Allows you to remove cameras from the

Camera List.

SwannEye Plus App Camera Setup

The SwannEye Plus app is great for on-the-fly monitoring, but before you can actually start

watching anything, you need to first register the camera with the app.

The SwannEye Plus app has some limitations - you can’t record videos and there isn’t any split

screen display. For these, you have to use the Windows software.

Registering the Camera

1 Tap to display the Add Camera screen.

2 If you are connected to the same network as your

camera (typically if your phone or tablet is connected to

your Wi-Fi at home and so is your camera) you will see

“Camera Found! (1)” as shown on the right. Simply tap

the UID of the discovered camera and finish the details

as per steps 4 and 5 below. Note if you have more than

one camera on your network you see more camera

UIDs in this list, set each one up separately.

3 If the camera is on a different network such as the

mobile network or the auto search did not find it, simply

tap and use your smartphone’s camera to

scan the QR code sticker which you will find on the

bottom of the camera. This automatically populates the

UID box with the camera’s UID, then just follow steps 4

and 5 to finish off.

Or if you prefer to do it manually, tap and

type the camera’s UID in the UID box carefully. Note

that the UID is case sensitive so make sure you use the

correct types of letters and number or it won’t connect.

4 Enter the camera’s password (default is 123456 but we

recommend you change this using the software on your

PC as soon as possible) in the Password box.

5 Tap the Name box and then enter a unique name for the

camera. We suggest calling it something that can help

you identify it easily. When you’re finished, tap to

return to the Camera List screen.

Using SwannEye Plus App

Tap to display the Edit Camera

screen where you can manage

camera settings such as name,

password, video & Wi-Fi and

reconnect the camera if it’s not

online.

Camera name

Connection details

To pan camera view,

swipe left or right

Mute video

Current Audio mode

Close Audio Mode menu

Hear what’s going on

near the camera

Talk to people near

the camera using

your smartphone’s

microphone

Tap to watch camera

on Live View

Take a snapshot

To tilt camera view,

swipe up or down

View and manage

snapshots

Connection status

The Camera List Screen

The Live View Screen

Using SwannEye Plus App

The Advanced Setting Screen

Tap to modify the camera’s

current password. The next

time you use SwannEye

Plus on your PC or another

smartphone, you will

need to re-enter the new

password for the camera.

Adjust light environment

mode to Indoor (50Hz),

Indoor(60Hz), Outdoor or

Night.

See model & version

number and other

information about the

camera.

Your currently connected

Wi-Fi network.

Tap to connect to a diferrent

Wi-Fi network (if available).

Adjust video quality to Min,

Low, Medium, High or Max.

Higher settings offer better

quality, but require more

bandwidth to stream.

Adjust video orientation

to Normal, Vertical Flip,

Horizontal Flip or Vertical

and Horizontal Flip.

Tap to change camera name

Show Advanced Setting screen

Tap to attempt re-connecting the

camera if it’s no longer online or has

timed out.

The Edit Camera Screen

The Live View Interface

• Open a web browser such as Internet Explorer (IE), Chrome, Firefox or Safari

and enter the IP address of your camera in the address bar. Make sure your

camera is connected to the network, otherwise nothing will show up.

To find out the IP address of your camera, refer to the quick summary in “Adding to

the Camera List” on page 7.

• Log in using the current username and password of your camera (the default is

admin / 123456).

• Next, select your viewing mode - Mode 1 for Internet Explorer or Mode 2 for

Chrome, Firefox and Safari. Note that certain functions are only available in

Internet Explorer.

• If you’re using IE and connecting to a camera for the first time, you will need to

download and install a plug-in first. The IE browser plug-in is quite small and

installation does not take long. Your operating system and/or virus protection

program may ask you for permission to run the file. Select the relevant options

available to complete installation. Restart your browser after installation.

Accessing the Camera via Web Browser

The Live View interface on the web browser is almost exactly the same as the main

interface for the SwannEye Plus software on the computer - it just looks slightly

different but operates in the same manner with a few additional features such as

vertical & horizontal patrolling and brightness & contrast adjustments.

Setting up Email Alerts via Web Browser

Your camera can send alerts and snapshots to an email address when motion events occur.

You must first configure your email account details and set up motion detection via the

camera’s web interface.

To set up email alerts:

1. Click the button at the bottom of the Live View interface on the web browser to

bring up the Advanced Settings page.

Configure Email

2. Click Mail Service Settings on the left navigation bar.

3. Enter your email account details into the appropriate fields.

• Sender: The email address that you want your camera to send alerts from. For

example, your_email@gmail.com

• SMTP Server: Select the SMTP address of your email server from the dropdown list.

If you want to use an email server other than the ones provided, manually enter it into

the field.

• SMTP Port: The SMTP port of your email server. This field will automatically self-

populate if you use any of the preset email servers.

• Need Authentication: If the SMTP server requires authentication, check this box and

then enter the username (for example, your_email@gmail.com) and password for your

email account.

• SSL: Whether the email server you’re using requires a secure link. If you’re not sure

what settings to use, check with your email service provider.

• Receiver: The email address(es) that your alerts will be sent to. You can specify up to

four (4) different email receipients.

• Test: Click to send a test email to the “Receiver” email address(es) specified above.

Setting up Email Alerts via Web Browser

4. When you have completed the email configuration, click the Setup button to save your

settings.

Enable Motion Detection, Email Notifications and Schedules

5. Now that your email account has been set up, it’s time to configure the motion

detection settings of your camera. Click Alarm Service Settings on the left navigation

bar.

6. Tick the Motion Detect Armed box to enable the motion detection function and then

adjust the sensitivity of the motion detection. The lower the value, the more sensitive

the motion detection will be.

7. Tick the Send Mail Notification When Alarm box. If you want a small snapshot to be

included with each email alert, tick the Upload Image When Alarm box. You can also

specify how frequently email alerts with snapshots are sent to you during a motion

detection event via the Upload Interval (in seconds) field.

8. Tick the Time Schedule box to display a timetable showing a 24-hour timeline for each

day of the week. Each box in the timeline represents 15 minutes in the 24-hour period.

The timetable allows you to choose the specific times and days to receive email alerts.

If you want to always receive email alerts, tick the Select All box.

9. To save the motion detection settings, click the Submit button.

Helpdesk / Technical Support Details

Swann Technical Support

All Countries E-mail: tech@swann.com

Telephone Helpdesk

USA Toll Free 1-800-627-2799

USA Exchange & Repairs 1-800-627-2799 (Option 1)

(M-F, 9am-5pm US PT)

AUSTRALIA 1300 138 324

NEW ZEALAND Toll Free 0800 479 266

UK 0203 027 0979

M440U160414E

Swann ads 440 User manual

Swann ads 440 User manual

Related papers

Other documents