Panasonic AW?HE60SN Operating Instructions Manual

Operating Instructions

HD Integrated Camera

PGQX1222ZAA/C1(E)M0912MS0 -FJ

ENGLISH

 HowtheOperatingInstructionsareconfigured

<Basics>:

The <Basics> describes the procedure for basic operation and installation. Before installing this unit, be

sure to take the time to read through <Basics> to ensure that the unit will be installed correctly.

<Operations and Settings> (this manual):

This <Operations and Settings> describes how to operate the unit and how to establish its settings.

Model No.

AW‑HE60HN

Model No.

AW‑HE60SN

Model No.

AW‑HE60HE

Model No.

AW‑HE60SE

2

Trademarks and registered trademarks

p Microsoft

®

, Windows

®

, Windows

®

7, Internet Explorer

®

,

ActiveX

®

and DirectX

®

are either registered trademarks or

trademarks of Microsoft Corporation in the United States

and other countries.

p Intel

®

and Intel

®

Core

TM

are trademarks or registered

trademarks of Intel Corporation in the United States and

other countries.

p Adobe

®

and Reader

®

are either registered trademarks or

trademarks of Adobe Systems Incorporated in the United

States and/or other countries.

p HDMI, the HDMI logo and High-Definition Multimedia

Interface are the trademarks or registered trademarks

of HDMI Licensing, LLC in the United States and other

countries.

p Apple, Mac, Mac OS, iPhone, iPod Touch, iPad, and Safari

are registered trademarks of Apple Inc., in the United

States and other countries.

p Android

TM

is a trademark of Google Inc.

p Other names of companies and products contained

in these Operating Instructions may be trademarks or

registered trademarks of their respective owners.

About copyright and licence

Distributing, copying, disassembling, reverse compiling,

reverse engineering, and also exporting in violation of export

laws of the software provided with this unit are expressly

prohibited.

Abbreviations

The following abbreviations are used in this manual.

p Microsoft

®

Windows

®

7 Professional SP1 32/64-bit is

abbreviated to “Windows 7”.

p Microsoft

®

Windows

®

XP Professional SP3 and Microsoft

®

Windows

®

XP Home Edition SP3 are abbreviated to

“Windows XP”.

p Windows

®

Internet Explorer

®

8.0 and Windows

®

Internet

Explorer

®

9.0 are abbreviated to “Internet Explorer”.

For the purposes of this manual, the model numbers of the

units are given as listed in the table below.

Model number

of unit

Model number

given in manual

AW-HE60HN

AW‑HE60

AW-HE60HE

AW-HE60SN

AW-HE60SE

AW-HE60HN

AW‑HE60H

AW-HE60HE

AW-HE60SN

AW‑HE60S

AW-HE60SE

AW-HS50N

AW‑HS50

AW-HS50E

AW-PS550N

AW‑PS550

AW-PS550E

AW-RP50N

AW‑RP50

AW-RP50E

AW-RP555N

AW‑RP555

AW-RP555L

AW-RP655N

AW‑RP655

AW-RP655L

Illustrations and screen displays featured in the

manual

p What is shown in the manual’s illustrations and screen

displays may differ from how it is actually appears.

p Functions which can be used by Windows only are

indicated using the

mark.

3

Contents

Before use ...........................................................................4

Overview ..........................................................................4

Required personal computer environment .......................4

Disclaimer of warranty......................................................5

Network security ..............................................................5

Concerning the plug-in viewer software ...........................6

Basic shooting operations ................................................7

How to turn the power on and off .....................................8

Turning the power on .......................................................8

Turning the power off .......................................................9

Selecting the units ............................................................10

Selecting the shooting modes (scene files) ...................10

Types of shooting modes ...............................................10

How to select the shooting mode ...................................11

Shooting ............................................................................13

What to do when encountering problems

in the basic shooting operations ................................14

More advanced operations ..............................................15

Manual shooting ...............................................................16

Manually adjusting the focus ..........................................16

Manually adjusting the iris ..............................................17

Manually adjusting the shutter speed ............................18

Manually adjusting the gain ...........................................19

Preset memories ...............................................................20

White balance adjustment ...............................................23

White balance adjustment ..............................................23

Black level (master pedestal) adjustment ......................27

Black level (master pedestal) adjustment.......................27

Genlock adjustment (AW‑HE60S only) ...........................29

Genlock adjustment .......................................................29

Basic operations ...............................................................32

When performing the operations

using the wireless remote control ..............................34

Control exercised from the Multi-Function

Controller AW-RP655 ................................................35

Control exercised from the Multi Hybrid

Control Panel AW-RP555 ..........................................37

Control exercised from the Remote

Camera Controller AW-RP50 ....................................39

Camera menu items .........................................................40

Setting the camera menu items .....................................40

Top Menu screen ...........................................................40

Camera screen (when FullAuto is selected) ..................41

Camera screen (when Manual1 to 3 is selected) ...........41

Contrast screen ..............................................................42

Picture 1/2 screen ..........................................................43

Picture 2/2 screen ..........................................................44

16-axis color matrix ........................................................45

System screen ...............................................................46

Genlock screen (AW-HE60S only) .................................46

Output screen ................................................................47

Other 1/2 screen ............................................................49

Other 2/2 screen ............................................................50

Maintenance screen .......................................................51

Firmware Version screen ...............................................51

IP Network screen ..........................................................52

Camera menu item table ..................................................53

Controls and settings from web screen .........................55

Displaying the web screen

using a personal computer ........................................56

Live screen: Single display mode ...................................58

Live screen: Multi display mode .....................................63

Setup screen ..................................................................64

Web screen item table ......................................................96

Displaying the web screen using a mobile terminal ...100

System log displays .......................................................104

Limiters ............................................................................105

Setting/releasing the limiters ........................................106

Basic limiter operations ................................................106

Setting the limiters .......................................................106

Releasing the limiters ...................................................107

Resetting the limiters ...................................................107

Safe mode .......................................................................108

Concerning the safe mode ...........................................108

Notes on Windows

®

7 .....................................................109

System requirements for a personal computer ............109

Trademarks and Registered Trademarks .....................109

Precautions when using Windows 7 ............................110

Index ................................................................................115

4

Before use

pwOverview

p This unit is a compact full HD camera integrated with a

pan-tilt head and featuring a 1/3-type full HD MOS sensor

and digital signal processor (DSP).

p In addition to its optical 18 zoom lens, the unit comes

with a 10 digital zoom to achieve high-quality shooting

that overflows with ambiance.

p The unit features a night mode, making it possible to shoot

even under very-low-brightness conditions by exposing

subjects to infrared rays.

p Two models are available: the HDMI model AW-HE60H

which is ideal for distributing the signals of TV conference

and other video events, and the SDI output model

AW-HE60S which is ideal for creating content.

IP video transfer and IP control can be performed for both

models.

It is also possible to connect to an existing camera

controller using serial control.

pwRequired personal computer

environment

CPU Intel

®

Core

TM

2 Duo 2.4 GHz or faster or

CPU with the equivalent specifications

Memory [When using Windows]

512 MB or more

(When using Microsoft

®

Windows

®

7: 1 GB [32 bits] or 2 GB [64 bits] or

more)

[When using Mac OS X]

2 GB or more

Network

function

10BASE-T or 100BASE-TX port 1

Image display

function

Resolution: 1024  768 pixels or

more

Color generation: True Color 24 bits or

more

Supported

operating

system and

Web browser

Microsoft

®

Windows

®

7 Professional

SP1 64-bit*

1

Microsoft

®

Windows

®

7 Professional

SP1 32-bit*

1

Windows

®

Internet Explorer

®

8.0*

2

Windows

®

Internet Explorer

®

9.0*

2

Microsoft

®

Windows

®

XP Home Edition

SP3*

3

Microsoft

®

Windows

®

XP Professional

Edition SP3*

3

Windows

®

Internet Explorer

®

8.0*

2

Apple

Mac OS X v10.5

Safari 5.0.6

Apple

Mac OS X v10.6

Safari 5.1.7

Apple

Mac OS X v10.7

Safari 5.1.7

*1: This cannot be used in the

Windows

®

XP compatibility mode.

*2: This cannot be used with the 64-bit

version of Internet Explorer

®

8.0.

*3: The Microsoft

®

Windows

®

XP

Professional x64 Edition is not

supported.

Other CD-ROM drive

(for using the Operating Instructions and

various software)

DirectX

®

9.0c and up

Adobe

®

Reader

®

(for browsing the Operating Instructions

on the CD-ROM)

5

Before use

(continued)

IMPORTANT

p Failure to provide the required personal computer

environment may slow down the delineation of

the images on the screen, make it impossible for

the web browser to work and cause other kinds of

problems.

p When using Microsoft

®

Windows

®

7, refer to the “Notes on

Windows

®

7” (page 109) for details on the personal computer

environment that is required and on the precautions and

other items.

pwDisclaimer of warranty

IN NO EVENT SHALL Panasonic Corporation BE LIABLE

TO ANY PARTY OR ANY PERSON, EXCEPT FOR

REPLACEMENT OR REASONABLE MAINTENANCE OF

THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT

LIMITED TO BELOW:

1 ANY DAMAGE AND LOSS, INCLUDING WITHOUT

LIMITATION, DIRECT OR INDIRECT, SPECIAL,

CONSEQUENTIAL OR EXEMPLARY, ARISING OUT

OF OR RELATING TO THE PRODUCT;

2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY

INAPPROPRIATE USE OR NEGLIGENT OPERATION

OF THE USER;

3 UNAUTHORIZED DISASSEMBLE, REPAIR OR

MODIFICATION OF THE PRODUCT BY THE USER;

4 INCONVENIENCE OR ANY LOSS ARISING WHEN

IMAGES ARE NOT DISPLAYED, DUE TO ANY

REASON OR CAUSE INCLUDING ANY FAILURE OR

PROBLEM OF THE PRODUCT;

5 ANY PROBLEM, CONSEQUENTIAL

INCONVENIENCE, OR LOSS OR DAMAGE, ARISING

OUT OF THE SYSTEM COMBINED BY THE DEVICES

OF THIRD PARTY;

6 ANY DEMANDS FOR COMPENSATION, CLAIMS,

ETC. OCCASIONED BY THE INFRINGEMENT OF

PRIVACY BY INDIVIDUALS OR ORGANIZATIONS

WHOSE IMAGES WERE SHOT BY THE USER

BECAUSE THESE IMAGES (INCLUDING THE

RECORDINGS MADE) WERE MADE AVAILABLE

BY THE USER BECAUSE IN THE PUBLIC DOMAIN

FOR SOME REASON OR OTHER OR BECAUSE THE

IMAGES ENDED UP BEING USED FOR PURPOSES

OTHER THAN THE ONE DESCRIBED ABOVE;

7 LOSS OF REGISTERED DATA CAUSED BY ANY

FAILURE.

pwNetwork security

As you will use this unit connected to a network, your

attention is called to the following security risks.

1 Leakage or theft of information through this unit

2 Use of this unit for illegal operations by persons with

malicious intent

3 Interference with or stoppage of this unit by persons

with malicious intent

It is your responsibility to take precautions such as those

described below to protect yourself against the above

network security risks.

p Use this unit in a network secured by a firewall, etc.

p If this unit is connected to a network that includes

personal computers, make sure that the system is not

infected by computer viruses or other malicious entities

(using a regularly updated antivirus program, anti-spyware

program, etc.).

p Protect your network against unauthorized access by

restricting users to those who log in with an authorized

user name and password.

p Apply measures such as user authentication to protect

your network against leakage or theft of information,

including image data and authentication information (user

names and passwords).

p Do not install the camera in locations where the camera or

the cables can be destroyed or damaged by persons with

malicious intent.

Concerning user authorization

This unit uses BASIC authentication as the user

authentication (authorization) function.

When BASIC authentication is used without a dedicated

line, there is a risk of the password being intercepted. It is

recommended that host authentication be used instead.

Usage restrictions

Use of the same segment is recommended for the network

in which the unit and the controller or personal computer are

connected.

If the equipment uses connections with different segments,

events based on the settings inherent to the network

equipment, for instance, may occur so check this thoroughly

prior to operation.

6

Before use

(continued)

pwConcerning the plug‑in viewer

software

p This is necessary only when using a personal computer

running Windows.

In order to display the IP videos on this unit, the “Network

Camera View 4” plug-in viewer software must be installed.

Either install the software directly from the unit or click the

[Install] button of the “plug-in viewer software” on the menu of

the CD-ROM supplied, and follow the on-screen instructions

to install the software.

p When the unit is purchased, “Automatic installation

of viewer software” is set to “On”. Refer to page 65 if a

message appears on the information bar of the browser.

p When a Live screen is first displayed from the personal

computer, the screen on which to install ActiveX required

to display the camera images appears. Follow the

on-screen instructions to install the software.

p If the installation screen is displayed every time the screen

is switched even after ActiveX has been installed, reboot

the personal computer.

p A license to use the plug-in viewer software is required for

every personal computer which uses the software.

The number of times the plug-in viewer software has been

automatically installed can be checked on the “Product

info. screen” (page 92) under “Maintenance”.

Consult the dealer from whom you purchased the unit

concerning these licenses.

7

Basic shooting operations

1 Set the subject brightness to the appropriate

level.

2 Turn on the power of all the units and devices

in the system.

3 Select the unit to be operated.

Even when using only one unit, it must still be selected

from the wireless remote control or controller.

4 Select the shooting mode.

Select one of the four (FullAuto, Manual1, Manual2 and

Manual3) preset shooting modes (scene files), each of

which corresponds to a set of circumstances in which

the subject will be shot.

Select the mode that satisfies the shooting conditions

and suits your preferences.

When continuing to shoot in the same circumstances,

there is no need to select another mode.

5 Start shooting.

(After shooting, turn off the power of all the

units and devices in the system.)

p If “FullAuto” has been selected as the setting

for Scene on the camera menu, for example, all

the auto settings will be turned on, and manual

operations will no longer be possible for some of

the items.

Note

With the basic operations, it is assumed that the focus, iris

and white balance will be adjusted automatically (as per the

factory settings).

If the settings have already been changed and the original

settings are to be restored, refer to the “What to do when

encountering problems in the basic shooting operations”

(page 14) and “Camera screen” (page 41) in “Camera menu

items”.

8

How to turn the power on and off

pwTurning the power on

When performing the operations

using the wireless remote control

1 Set all the power switches of the units and

devices connected in the system to ON.

p This unit does not have a power switch.

When power is supplied to it, the status display lamp

will light up orange.

The initial operation is then performed, and after this

the unit is set to the standby mode.

2 Press one of the [CAM1] to [CAM4] buttons on

the wireless remote control to select the unit.

3 Press the [ON/STANDBY] button on the

wireless remote control for 2 seconds.

The POWER ON mode is established, images are

output, and control can be exercised.

p The unit’s status display lamp now lights up green.

p It takes about 30 seconds per unit for the initial

settings operation to be completed. During this

period, the unit cannot be operated.

(Status display lamp: light up orange)

p When transferring to the STAND BY mode

(Status display lamp: Orange)

The pan/tilt position is stored in the memory, and

the pan/tilt unit is moved so that it points backwards.

p When transferring to the POWER ON mode

(Status display lamp: Green (after the initial setting

operation is completed))

The pan/tilt unit is moved to the position which was

stored in the memory when the transition to the

STAND BY mode was made.

p POWER ON preset

The pan/tilt unit is moved to the setting, which was

established immediately prior to the transition to the

STAND BY mode, when the power has been turned

on.

p If the power is turned off without transferring to the

STAND BY mode, the pan/tilt unit position will not

be stored in the memory or reflected in the POWER

ON preset. The zoom position is stored using the

setting established immediately before the power is

turned off.

Notes

4 If a multiple number of units are going to be

used, repeat steps

2 and 3 as required.

The unit’s status display lamp blinks green when a signal

matched by the remote control ID has been received, and

it blinks orange when a signal that is not matched by the

remote control ID has been received.

When performing the operations using the controller

When the AW‑RP655 or AW‑RP555 is connected:

1 Set all the power switches of the units and

devices connected in the system to ON.

p This unit does not have a power switch.

When power is supplied to it, the status display lamp

will light up orange.

The initial operation is then performed, and after this

the unit is set to the standby mode.

2 Set the [OPERATE] switch on the controller to

ON.

The POWER ON mode is established, images are

output, and control can be exercised.

p The unit’s status display lamp now lights up green.

p It takes about 30 seconds per unit for the initial

settings operation to be completed. During this

period, the unit cannot be operated.

(Status display lamp: light up orange)

p When transferring to the STAND BY mode

(Status display lamp: Orange)

The pan/tilt position is stored in the memory, and

the pan/tilt unit is moved so that it points backwards.

p When transferring to the POWER ON mode

(Status display lamp: Green (after the initial setting

operation is completed))

The pan/tilt unit is moved to the position which was

stored in the memory when the transition to the

STAND BY mode was made.

p POWER ON preset

The pan/tilt unit is moved to the setting, which was

established immediately prior to the transition to the

STAND BY mode, when the power has been turned

on.

p If the power is turned off without transferring to the

STAND BY mode, the pan/tilt unit position will not

be stored in the memory or reflected in the POWER

ON preset. The zoom position is stored using the

setting established immediately before the power is

turned off.

Notes

Before setting the [OPERATE] switch on the controller to ON,

be absolutely sure to set all the power switches of the units

and devices connected in the system to ON.

For further details, refer to the Operating Instructions of the

controller.

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

9

How to turn the power on and off

(continued)

pwTurning the power off

When performing the operations

using the wireless remote control

1 Press one of the [CAM1] to [CAM4] buttons on

the wireless remote control to select the unit.

2 Press the [ON/STANDBY] button on the

wireless remote control for 2 seconds.

The unit’s power is turned off.

p The unit’s status display lamp now lights up orange.

3 If a multiple number of units are used, repeat

steps

1 and 2 as required.

4 Set all the power switches of the units and

devices connected in the system to OFF.

p When transferring to the STAND BY mode

(Status display lamp: Orange)

The pan/tilt position is stored in the memory, and

the pan/tilt unit is moved so that it points backwards.

p When transferring to the POWER ON mode

(Status display lamp: Green (after the initial setting

operation is completed))

The pan/tilt unit is moved to the position which was

stored in the memory when the transition to the

STAND BY mode was made.

p POWER ON preset

The pan/tilt unit is moved to the setting, which was

established immediately prior to the transition to the

STAND BY mode, when the power has been turned

on.

p If the power is turned off without transferring to the

STAND BY mode, the pan/tilt unit position will not

be stored in the memory or reflected in the POWER

ON preset. The zoom position is stored using the

setting established immediately before the power is

turned off.

Notes

When performing the operations using the controller

When the AW‑RP655 or AW‑RP555 is connected:

1 Set the [OPERATE] switch on the controller to

OFF.

The power of all the cameras (including the unit)

connected to the controller is turned off.

p The unit’s status display lamp now lights up orange.

2 Set all the power switches of the units and

devices connected in the system to OFF.

p When transferring to the STAND BY mode

(Status display lamp: Orange)

The pan/tilt position is stored in the memory, and

the pan/tilt unit is moved so that it points backwards.

p When transferring to the POWER ON mode

(Status display lamp: Green (after the initial setting

operation is completed))

The pan/tilt unit is moved to the position which was

stored in the memory when the transition to the

STAND BY mode was made.

p POWER ON preset

The pan/tilt unit is moved to the setting, which was

established immediately prior to the transition to the

STAND BY mode, when the power has been turned

on.

p If the power is turned off without transferring to the

STAND BY mode, the pan/tilt unit position will not

be stored in the memory or reflected in the POWER

ON preset. The zoom position is stored using the

setting established immediately before the power is

turned off.

Notes

For further details, refer to the Operating Instructions of the

controller.

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

10

Selecting the units

Up to four units can be operated using one wireless remote

control.

Up to five units can be operated using one controller.

Select the unit (or units) to be operated from the wireless

remote control or controller.

Even when using only one unit, it must still be selected.

When performing the operations

using the wireless remote control

1 Press the [CAM1], [CAM2], [CAM3] or [CAM4]

button.

The unit’s status display lamp blinks green when a signal

matched by the remote control ID has been received,

and it blinks orange when a signal that is not matched by

the remote control ID has been received.

When performing the operations using the controller

When the AW‑RP655 is connected:

1 Press the [1], [2], [3], [4] or [5] button of

[CONTROL/PREVIEW MONITOR OUT SEL].

When the AW‑RP555 is connected:

1 Press the [1], [2], [3], [4] or [5] button of

[CONTROL].

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

Selecting the shooting modes (scene files)

pwTypes of shooting modes

This unit has four preset shooting modes, each of which

corresponds to a set of circumstances in which the subject

will be shot.

Select the mode that satisfies the shooting conditions and

suits your preferences.

The settings can be changed by menu operations.

p The results of the white balance and other adjustments

are stored in the memory separately by shooting mode.

Be absolutely sure to select the shooting mode before

making any adjustments.

p If “FullAuto” has been selected as the setting

for Scene on the camera menu, for example, all

the auto settings will be turned on, and manual

operations will no longer be possible for some of

the items.

Note

FullAuto

The shutter speed and lens iris setting are adjusted

automatically.

Manual1

The settings of your preferences can be established

in line with the shooting scene, lighting and other

conditions.

Manual2

The settings of your preferences can be established

in line with the shooting scene, lighting and other

conditions.

Manual3

The settings of your preferences can be established

in line with the shooting scene, lighting and other

conditions.

11

Selecting the shooting modes (scene files)

(continued)

pwHow to select the shooting

mode

When performing the operations

using the wireless remote control

2, 8

4, 6, 7

3, 5, 7

1

1 Press the [CAM1], [CAM2], [CAM3] or [CAM4]

button to select the unit.

2 Press the [MENU] button for 2 seconds.

The Top Menu is displayed.

Top Menu

Camera Scene: FullAuto

System

Maintenance

3 Press the [] or [] button to bring the cursor

to “Camera”.

4 Press the [] button.

The “Camera” sub-menu is displayed on the monitor.

Camera

Scene FullAuto

Contrast Level 0

Day/Night Day

Return

5 Press the [] or [] button to bring the cursor

to “Scene”.

6 Press the [] button.

The shooting mode blinks.

7 Press the [] or [] button to select the

shooting mode (FullAuto, Manual1, Manual2 or

Manual3) to be used, and press the [] button

to enter the selection.

8 Press the [MENU] button for 2 seconds.

The camera menu display is exited.

12

Selecting the shooting modes (scene files)

(continued)

When performing the operations using the controller

When the AW‑RP655 is connected:

1 Press one of the [1] to [5] buttons of

[CONTROL/PREVIEW MONITOR OUT SEL] to

select the unit which is to be operated.

2 Press the [MENU] button to set the LCD panel

display to the menu mode.

3 Turn the jog dial (main) until CAMERA SETTING

appears, and press the [OK] button.

CAMERA SETTING

OK Key

4 When the scene selection menu has appeared

on the LCD panel, select the scene to be set,

and press the [OK] button.

SCENE HALOGEN

OK Key

The scene names displayed on the LCD panel correlate

with the scene files of the AW-HE60 as shown below.

AW‑RP655 display AW‑HE60 scene file

HALOGEN Manual1

FLUORESCENT Manual2

OUTDOOR Manual3

USER FullAuto

5 When the following message appears on the

LCD panel, press the [MENU] button twice to

exit the menu mode.

OPEN CAMERA MENU ?

OK Key

When the AW‑RP555 is connected:

1 Press the [1], [2], [3], [4] or [5] button of

[CONTROL] to select the unit.

2 Press the [1], [2], [3] or [USER] button of

[SCENE FILE] to select the shooting mode.

Shooting mode [SCENE FILE] button

Manual1 [1]

Manual2 [2]

Manual3 [3]

FullAuto [USER]

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

13

Shooting

When performing the operations

using the wireless remote control

pqChanging the camera’s direction

Moving the camera toward the left or right (panning):

Press the [] or [] button.

Moving the camera up or down (tilting):

Press the [] or [] button.

Moving the camera diagonally:

Press the [] or [] button and [] or [] button at

the same time.

Returning the camera to the reference position:

Press the [HOME] button for 2 seconds.

pqUsing the zoom function

Zooming in (the subject becomes magnified in size):

Press the [T] button of [ZOOM].

Zooming out (the subject becomes reduced in size):

Press the [W] button of [ZOOM].

pqSwitching the direction or zoom speed

Changing the direction or zoom at high speed:

Press the [FAST] button.

When this button is held down, the speed can be set to

an even higher speed.

When it is tapped, the normal speed (high speed) is

restored.

Changing the direction or zoom at low speed:

Press the [SLOW] button.

When this button is held down, the speed can be set to

an even lower speed.

When it is tapped, the normal speed (low speed) is

restored.

The lens focus control speed is also changed at the same

time.

When performing the operations using the controller

pqChanging the camera’s direction

Moving the camera toward the left or right (panning):

Tilt the [PAN/TILT] lever toward L or R.

Moving the camera up or down (tilting):

Tilt the [PAN/TILT] lever toward UP or DOWN.

Moving the camera diagonally:

Tilt the [PAN/TILT] lever diagonally.

Returning the camera to the reference position:

If the controller has a [HOME] button, press the

[HOME] button.

pqUsing the zoom function

Zooming in (the subject becomes magnified in size):

Tilt the [ZOOM] lever toward the TELE direction.

Zooming out (the subject becomes reduced in size):

Tilt the [ZOOM] lever toward the WIDE direction.

p The indicator displays of the AW-RP655 are

indicators that show the positions of the optical

zoom. They will not work for electronic zooming.

Note

pqChanging the direction or zoom speed

AW‑RP655 and AW‑RP555

1 Press the [SPEED] button.

Each time the [SPEED] button is pressed, the control

speed is switched between the high speed (the button’s

lamp is off) and low speed (the button’s lamp is lit).

The lens focus control speed is also changed at the

same time.

AW‑RP50

Refer to the Operating Instructions of the controller.

14

What to do when encountering problems in

the basic shooting operations

If the trouble is not resolved by taking the action suggested

below, refer to “Troubleshooting” (page 43 in the <Basics>).

When performing the operations

using the wireless remote control

The unit does not move.

p Press the [CAM1], [CAM2], [CAM3] or [CAM4] button to

select the unit which is to be operated.

If only one unit is being used, it is normally selected using

the [CAM1] button.

p Check that the IR ID switches have been set correctly.

(Refer to pages 37 and 40 in the <Basics>.)

p If the unit’s status display lamp is off or lights up orange, it

means that the unit’s power is not on.

Refer to “Turning the power on” (page 8), and turn on the

power.

p If the unit’s status display lamp does not blink even when

the wireless remote control is operated near the unit’s

wireless remote control signal light-sensing area, it means

that the wireless remote control’s batteries have run down.

Replace the batteries.

Multiple color bands (color bars) are displayed.

Press the [MODE] button to switch to the camera picture.

The menu screen is displayed.

Press the [MENU] button for 2 seconds to exit the camera

menu.

The lens focus is not adjusted automatically.

Press the [A/FOCUS] button to switch to auto focusing.

(Auto focusing does not work during panning or tilting

operations.)

The camera picture is too light or too dark.

1. Press the [A/IRIS] button to switch the lens iris

adjustment to auto.

2. Press the [AUTO] button of [GAIN] to switch the gain

adjustment to auto.

Something is wrong with the coloring of the

camera pictures.

Refer to “Auto tracking white adjustment (ATW)” (page 25), and

switch to “ATW”.

The camera menus are not displayed.

When color bar signals are output, the camera menus are

not displayed with composite signals.

To operate the camera menus with composite signals, set the

color bar display to OFF.

When performing the operations using the controller

The unit does not move.

p Select the unit to be operated by following the procedure

below.

When the AW‑RP655 is connected:

Press the [1], [2], [3], [4] or [5] button of [CONTROL/

PREVIEW MONITOR OUT SEL].

When the AW‑RP555 is connected:

Press the [1], [2], [3], [4] or [5] button of [CONTROL].

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

p If the [OPERATE] lamp on the controller is off, it means

that the power of the controller is not on.

p If the unit’s status display lamp is off or lights up orange, it

means that the unit’s power is not on.

Refer to “Turning the power on” (page 8), and turn on the

power.

Multiple color bands (color bars) are displayed.

Press the [MODE] button to switch to the camera picture.

The menu screen is displayed.

Press the [MENU] button to exit the camera menu.

The lens focus is not adjusted automatically.

Press the [EXT(AF)] button to switch to auto focusing.

(Auto focusing does not work during panning or tilting

operations.)

The camera picture is too light or too dark.

1. Press the [IRIS] button several times to turn on its lamp,

and switch the lens iris adjustment to auto.

2. Press the [GAIN] button several times to turn on its lamp,

and switch the gain adjustment to auto.

Something is wrong with the coloring of the

camera pictures.

Refer to “Auto tracking white adjustment (ATW)” (page 25), and

switch to “ATW”.

The camera menus are not displayed.

When color bar signals are output, the camera menus are

not displayed with composite signals.

To operate the camera menus with composite signals, set the

color bar display to OFF.

15

More advanced operations

Manual shooting (see pages 16 to 19)

p Manual adjustment of focus

p Manual adjustment of iris

p Manual adjustment of shutter speed

p Manual adjustment of gain

Preset memories (see pages 20 to 22)

p Up to 100 settings for the camera direction (panning and

tilting), zoom, focus, iris, gain up and white balance can be

registered in the preset memories, and called.

p The number of settings that can be registered and

called depends on the type of wireless remote control

(12 settings) or controller that is used for operation.

White balance adjustment

(see pages 23 to 26)

p This adjustment is performed to express the white

accurately. Its setting also has an effect on the color tones

of the entire screen.

p It must be performed when using the unit for the first

time or when the unit has not been used for a prolonged

period.

p It must be performed when the lighting conditions or

brightness has changed.

p Once the white balance has been attained, no further

adjustment is required provided that the unit is going to be

used under the same conditions.

Black level (master pedestal) adjustment

(see pages 27 to 28)

p This adjustment is performed to align the black level

(pedestal level) of a multiple number of cameras.

p Ask your dealer to perform this adjustment.

Genlock adjustment (AW‑HE60S only)

(see pages 29 to 31)

p This adjustment is performed to achieve phase alignment

by applying external synchronization (genlock) when a

multiple number of cameras will be used or when the unit

will be used in combination with other devices.

p Ask your dealer to perform this adjustment.

16

Manual shooting

pwManually adjusting the focus

The lens focus can be adjusted manually.

When performing the operations

using the wireless remote control

1 Press the [M/FOCUS] button to switch the

focus to manual adjustment.

2 Press the [F] or [N] button of [FOCUS] to adjust

the focus.

When the [F] button is pressed, the focus moves further

away (far); conversely, when the [N] button is pressed, it

moves nearer (near).

The speed of focusing and other adjustments can

be switched to fast or slow by pressing the [FAST] or

[SLOW] button, respectively.

3 If necessary, press the [A/FOCUS] button to

return the focus to the automatic adjustment.

When performing the operations using the controller

When the AW‑RP655 is connected:

1 Press the [EXT(AF)] button to switch the focus

to manual adjustment.

2 Adjust the focus manually by turning the dial

above the lit [FOCUS] lamp whether it is the

lamp of the [PAN/TILT] lever or [ZOOM] lever.

Furthermore, every time the [SPEED] button is pressed,

the speed of the focusing and other adjustments can be

switched to fast or slow.

3 If necessary, press the [EXT(AF)] button to

return the focus to the automatic adjustment.

When the AW‑RP555 is connected:

1 Press the [(AF)EXT] button to switch the focus

to manual adjustment.

2 Adjust the focus manually by tilting the

[FOCUS] lever.

Furthermore, every time the [SPEED] button is pressed,

the speed of the focusing and other adjustments can be

switched to fast or slow.

3 If necessary, press the [(AF)EXT] button to

return the focus to the automatic adjustment.

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

p When the focus is set to manual, the subject may

go out of focus during panning, tilting and zooming.

Therefore, the unit comes with a function which

compensates for this. (Focus compensation during

zooming function: Focus ADJ With PTZ.)

This function was set to ON at the factory.

If the function has been set to OFF, either adjust the

focus, as required, after zooming or set the focus to

auto. (See page 49 and page 81.)

Note

17

Manual shooting

(continued)

pwManually adjusting the iris

The lens iris can be adjusted manually.

When performing the operations

using the wireless remote control

1 Press the [M/IRIS] button to switch the iris to

manual adjustment.

2 Adjust the iris using the [IRIS +] or [IRIS –]

button.

Press the [IRIS +] button to adjust the lens iris in the

opening direction; conversely, press the [IRIS –] button to

adjust the lens iris in the closing direction.

3 If necessary, press the [A/IRIS] button to return

the iris to the automatic adjustment.

When performing the operations using the controller

When the AW‑RP655 is connected:

1 Press the [IRIS] button several times to turn

off the button’s lamp and switch to manual

adjustment.

2 Adjust the iris manually by turning the dial

above the lit [IRIS] lamp whether it is the lamp

of the [PAN/TILT] lever or [ZOOM] lever.

3 If necessary, press the [IRIS] button several

times and turn on its lamp to return the iris to

the automatic adjustment.

When the AW‑RP555 is connected:

1 Press the [IRIS] button to turn off its lamp and

switch to manual adjustment.

2 Turn the [LEVEL] dial of [IRIS] to adjust the iris

manually.

The position of the [LEVEL] dial does not represent an

absolute value.

This is why the brightness may differ from one camera to

another even when the dial is set to the same position.

3 If necessary, press the [IRIS] button to turn on

its lamp and switch to automatic adjustment in

order to return the iris to automatic adjustment.

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

p In the night mode, the iris is set to open as a measure to

prevent video spying.

Adjust the brightness at the light source.

18

Manual shooting

(continued)

pwManually adjusting the shutter

speed

The shutter speed can be set using two methods. One is

a method that specifies the time (where a time such as

1/250 sec. is designated), and the other is a method that

specifies the frequency (where synchro scan, 60.24 Hz*, etc.

is designated).

When shooting a TV screen or PC monitor screen, the

horizontal noise generated when the screen is shot can

be minimized by adjusting the frequency to the screen

frequency using synchro scan.

*: This describes when 59.94 Hz has been set as the unit’s

frequency.

When performing the operations

using the wireless remote control

Perform the adjustments on the Camera menu.

For further details, refer to the [Shutter Mode] and

[Step/Synchro] items on page 42.

When performing the operations using the controller

These operations can be performed in the same procedures

as “When performing the operations using the wireless

remote control” by following the operation steps in “Basic

operations” (pages 32 to 39).

When the AW‑RP555 is connected:

1 Press the [SHUTTER] button and turn its lamp

on.

The shutter speed set ahead of time is selected.

2 If necessary, press the [SHUTTER] button to

turn its lamp off in order to return the shutter to

the OFF setting.

pq How to set the shutter speed using the AW‑RP555

1 With the [MEMORY] button held down, press

the [SHUTTER] button.

The [1] to [5] and [6] to [10] buttons of [PRESET] blink

alternately.

2 Press one of the [1] to [8] buttons or the [10]

buttons of [PRESET] — whichever button

corresponds to the shutter speed which is to

be set.

Any of the shutter speeds in the table below can be set.

[When 59.94 Hz has been set as the unit’s frequency]

[1] [2] [3] [4] [5]

1/100 1/250 1/500 1/1000 1/2000

[6] [7] [8] [10]

1/4000 1/10000 Synchro Scan OFF

[When 50 Hz has been set as the unit’s frequency]

[1] [2] [3] [4] [5]

1/120 1/250 1/500 1/1000 1/2000

[6] [7] [8] [10]

1/4000 1/10000 Synchro Scan OFF

p Any change in the shutter speed is reflected the next

time the [SHUTTER] button is pressed and its lamp is

turned on.

p When OFF is selected, the shutter will not operate

even when the [SHUTTER] button is pressed.

p Select the synchro scan setting on the menu.

p The shutter speed setting performed here is stored in

the memory even when the power of the AW-RP555

is turned off.

For further details, refer to the Operating Instructions of the

AW-RP555.

19

Manual shooting

(continued)

pwManually adjusting the gain

There are two ways to adjust the gain. One way involves

using the buttons on the wireless remote control or controller;

the other way involves using the Camera menu or Web

setting.

The gain can be adjusted more precisely using the Camera

menu or Web setting.

For further details, refer to the [Gain] item on page 42 and

page 72.

p When adjusting the gain, the light quantity may

change suddenly (causing the image output to be

subjected to a shock).

Note

When performing the operations

using the wireless remote control

1 Press the [OFF], [LOW] or [HI] button.

These buttons enable the gain increase to be selected in

three steps.

[LOW] is used to select 9 dB; [HI] is used to select 18 dB.

2 If necessary, press the [AUTO] button in order

to return the gain to the automatic adjustment

(AGC).

When performing the operations using the controller

When the AW‑RP655 is connected:

1 Press the [GAIN] button to turn off its lamp, and

then switch to manual adjustment.

The preset gain increase amount is now selected.

For further details on the gain increase amount setting,

refer to the Operating Instructions of the AW-RP655.

2 If necessary, press the [GAIN] button and turn

on the button in order to return the gain to the

automatic adjustment (AGC).

When the AW‑RP555 is connected:

1 Press the [GAIN] button to turn off its lamp.

Each time this button is pressed, one of the three gain

increase amounts can be selected in sequence.

The current status is displayed as follows.

[MANU]

[L] lamp

[MANU]

[H] lamp

[GAIN]

button

0 dB Off Off Off

LOW Lit Off Off

HIGH Off Lit Off

AUTO Off Off Lit

Other Lit Lit Off

2 If necessary, press the [GAIN] button several

times and turn on its lamp in order to return the

gain to the automatic adjustment (AGC).

When the AW‑RP50 is connected:

Refer to the Operating Instructions of the controller.

In any case, the maximum gain of the automatic adjustment

can be set by the camera menu or Web setting.

For further details, refer to the [AGC Max Gain] item on

page 42 and page 72.

20

Preset memories

This unit enables up to 100 settings for the camera direction

(panning and tilting), zoom, focus, iris, gain and white

balance to be registered in its preset memories, and called.

However, the number of settings that can be registered and

called depends on the type of wireless remote control or

controller that is used for operation.

p The focus and iris operating modes (manual and auto

settings) are not registered.

The current focus and iris values are registered.

p The focus and iris values can be recalled only when the

manual settings are applicable.

p AWB A, AWB B or ATW is registered as the white balance

setting. The values selected when AWB was established

are recalled as the adjustment values of AWB A or

AWB B.

p The AWB Mode (ATW, AWB A and AWB B) stored using

the AW-RP655 are recalled only when the AW-RP655 is

connected.

p When there is a large difference in the environmental

temperature between the time of registration and the

time the setting is called, displacement of the preset

position may occur.

p If displacement occurs, perform registration again.

p While preset settings are being called, it is not

possible to perform manual operations such as

panning, tilting, zooming or iris adjustments.

p If, when one set of preset settings has been called,

another set of preset settings is then called, the first

set of preset settings which have been called will take

precedence.

Notes

When performing the operations

using the wireless remote control

Twelve settings (preset No.1 to No.12) can be registered and

called using the wireless remote control.

The [1] to [12] buttons correspond to the unit’s preset

memories No.1 to No.12.

pq Registering the settings in the preset memories

1 Display the picture to be shot on the monitor.

Operate the pan, tilt or zoom buttons to determine the

camera angle.

Adjust the focus, iris, gain and white balance if they need

to be adjusted.

2 While holding down the [PRESET] button, press

the button corresponding to the preset memory

number.

p If a preset memory number with an already registered

setting has been selected, the existing setting will be

erased and replaced with the new one.

pq Calling the settings of the preset memories

1 Press the button in which the preset memory

setting has been registered.

Page is loading ...

Panasonic AW?HE60SN Operating Instructions Manual

This manual is also suitable for

Panasonic AW?HE60SN Operating Instructions Manual

Related papers

Other documents