KINGgates Fred Myo 2 Owner's manual

Type
Owner's manual
KING gates - Brand of Antoniolli Mario & C. s a s
Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel. +39 0434 737082 - Fax +39 0434 783382
e-mail: [email protected] web: www.king-gates.com
MADE IN ITALY
Fred Myo 2
INSTRUCTION MANUAL
EN
2-channel radio receiver.
1- PRODUCT DESCRIPTION
2- ELECTRIC CONNECTIONS
Fred Myo 2 is a radio receiver with 2 outputs, monostable (when it receives the command, the output
acti
vates itself for 1 second).
1A - GENERAL DESCRIPTION
3- RADIO TRANSMITTER PROGRAMMING
Every operation (both radio transmitter
programming and channel configuration)
is done by the button.
The programming is signalled by the color of
the led, in particular:
- Green led: the operations concerning channel 1.
- Red led: the operations concerning channel 2.
3A - INTRODUCTION
Power supply 12-26 Vac/Vdc
Working temperature -20 ÷ +70
Reception frequency 433.920 MHz
No. storable codes 480
36mm
40mm
Relay contact Vac 1A 120V
Relay contact Vdc 1A 24Vdc
Absorption 60mA
1B - TECHNICAL FEATURES
Power +12/24Vac/dc
Ground
Programming
status signaling led
Programming
button
Normally open contact
channel 1 (NO)
Signal
Normally open contact
channel 2 (NO)
Soc
ket
Within
5 seconds
make a transmission
pushing the
desired
button
on the transmitter
(the led
switches off
and
on again)
Within 5 seconds
make a transmission
pushing the
desired
button
on the transmit-
ter
(the led switches
off and on again)
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
Press one time the
button on the re
ceiver.
The led swi
tches on
green
Press two times the
button on the re
ceiver.
The led turns
swi
tches on
red
3B - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 1
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
3C - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 2
Within 5 seconds
make a transmission
pressing
the desired
button
on the transmit-
ter
(the led switches
off and on again)
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
Press three times the
button on the re
ceiver.
The led flashes
orange
3D - DELETING OF A RADIO TRANSMITTER
During the flashing,
keep the button on the
recei
ver pressed
until the orange led
becomes fixed on.
Release the button.
When the o
range led
turns of
f, the memory
is e
rased.
Press three times the
button on the re
ceiver.
The third time,
keep
the button pushed.
The led flashes
orange
3E - DELETING OF ALL RADIO TRANSMITTER
1- PRODUCT DESCRIPTION
2- ELECTRIC CONNECTIONS
Fred Myo 2 is a radio receiver with 2 outputs, monostable (when it receives the command, the output
acti
vates itself for 1 second).
1A - GENERAL DESCRIPTION
3- RADIO TRANSMITTER PROGRAMMING
Every operation (both radio transmitter
programming and channel configuration)
is done by the button.
The programming is signalled by the color of
the led, in particular:
- Green led: the operations concerning channel 1.
- Red led: the operations concerning channel 2.
3A - INTRODUCTION
Power supply 12-26 Vac/Vdc
Working temperature -20 ÷ +70
Reception frequency 433.920 MHz
No. storable codes 480
36mm
40mm
Relay contact Vac 1A 120V
Relay contact Vdc 1A 24Vdc
Absorption 60mA
1B - TECHNICAL FEATURES
Power +12/24Vac/dc
Ground
Programming
status signaling led
Programming
button
Normally open contact
channel 1 (NO)
Signal
Normally open contact
channel 2 (NO)
Soc
ket
Within
5 seconds
make a transmission
pushing the
desired
button
on the transmitter
(the led
switches off
and
on again)
Within 5 seconds
make a transmission
pushing the
desired
button
on the transmit-
ter
(the led switches
off and on again)
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
Press one time the
button on the re
ceiver.
The led swi
tches on
green
Press two times the
button on the re
ceiver.
The led turns
swi
tches on
red
3B - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 1
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
3C - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 2
Within 5 seconds
make a transmission
pressing
the desired
button
on the transmit-
ter
(the led switches
off and on again)
Wait 5 seconds, or
push the button on the
recei
ver.
The led swi
tches off.
End prog
ramming.
Press three times the
button on the re
ceiver.
The led flashes
orange
3D - DELETING OF A RADIO TRANSMITTER
During the flashing,
keep the button on the
recei
ver pressed
until the orange led
becomes fixed on.
Release the button.
When the o
range led
turns of
f, the memory
is e
rased.
Press three times the
button on the re
ceiver.
The third time,
keep
the button pushed.
The led flashes
orange
3E - DELETING OF ALL RADIO TRANSMITTER
KING gates - Brand of Antoniolli Mario & C. s a s
Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel. +39 0434 737082 - Fax +39 0434 783382
e-mail: [email protected] web: www.king-gates.com
MADE IN ITALY
Fred Myo 2
INSTRUCTION MANUAL
EN
2-channel radio receiver.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

KINGgates Fred Myo 2 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages