Wren Kitchens BASE UNIT 600 Assembly Manual

Wren Kitchens
Brand
Wren Kitchens
Model
BASE UNIT 600
Type
Assembly Manual

This manual is also suitable for

BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
1000
600
800
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 1
(F) x8
Wooden Dowel
(G) x6
Cam Dowel
(Expanding)
(H) x6
Cam Lock
(K) x4
30mm
Screw
(L) x12
15mm
Screw
(N) x2
Door
Buer
(Z) x4
Shelf Peg
plastic
(M) x4
Cover
Cap
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel B
x2 End Panel
Panel E
x1 Rail
Panel C
x1 Base Panel
Shelf
x1
Sink
Rail
x1
Legs
x4 or 5
as req’d
Frontal
(Packed separately)
x1 or 2
as req’d
Panel A
x1 Back Panel
(800 - 1000 folded)
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
sink rail +
screws
600 - *o
800 - *o
1000 - *o
.pk.
t.141
Hinge Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 2
Step 1.
Seat dowel (F) into holes in
both end panels (B) as shown.
Step 2.
Seat cam dowel (G) into holes in
both end panels (B) as shown.
Step 4.
Join panels (C) to (B).
Insert cam lock (H).
Do NOT tighten until Step 6.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcass, for ease of tightening.
Do NOT use power tools with
cam dowel (G) or cam lock (H)
Seat (G)
cam dowel
into hole as
shown.
B
B
C
G
G
G
G
G
F
F
F
F
F
F
B
B
B
B
View from underside
View from underside
H
G
G
H
Sink Rail
Insert
Sink Rail
Insert
Dowel (F), Cam Dowel (G)
& Sink Rail Screw
Location detail
Sink Rail
Step 3.
Attach panels (C) & (E) to panels (B), using dowels (F)
(orange) and cam dowel (G) & cam lock (H) (blue) in
positions shown.
Insert sink rails as shown & secure with 2 x 15mm
screws (L) into panels (B).
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 3
9mm
Step 5.
Slide back panel (A) into
groove of end panels (B).
The back Panel (A) is to be modied accordingly
to suit Customer Requirements,prior to inserting
into cabinet. for 1000 width cabinets,
the Back panel.
Once back panel (A) is in position, ensure the
panel is ush & square with bottom of
end panels (B).
Step 6.
Hand tighten all cam locks (H), this will
expand cam dowels (G) and tighten the
unit together.
Step 7.
Ensure carcass is square. Secure back panel (A)
with 3 or 4 x 30mm screws (K) equally spaced at
the lower end of back panel (A) into base panel
(C), as shown.
Ensure you screw into the centre of the base
panels (C) (9mm from the edge).
B
E
C
A
K
B
C
A
600 Carcase used for example
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 4
Step 8.
Secure each of the legs into place
with 2 x 15mm screws (L).
600-800 Width Cabinets, 4 legs
1000 with Cabinets, 5 legs
Step 9.
Lightly hit centre peg of leg
base with hammer until ush.
Step 10.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning carcass
upright. Once in situ level accordingly.
Ensure legs are rotated as shown so that part
of it is supporting the end panels (B).
Front legs should have at edge to the front.
Leg position diagram
1000 Carcase used for example
C
C
B
L
L
C
B
B
Front
Front
Front
C
C
B
B
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 5
Step 11.
Attach hinge mounting plate
onto both End Panel or panels,(B) as shown, using Screws
which are already positioned within the Hinge Plates.
Hinge side or sides to be mounted in accordance to
customer kitchen plan.
Securing to adjacent units
Screw into any side units using the 30mm screws (K)
provided to secure to the unit. Screw just to the rear of the
hinge plate at the top and bottom of both sides of the unit,
place a cover cap (M) on the head to conceal it.
Securing to Wall
Secure unit to wall using 2 Screws. Drill 2 pilot holes through the back rail into the wall and insert
wall plugs, tighten the screws.
Screws for attaching to walls are not provided as these vary depending on your wall material
and construction.
Ensure appropriate xings for wall construction are used.
126mm
126mm
94mm
94mm
B
from base
from top
Hinge Plates
K
Worktop
Screw up through the front sink rail (and additional rail where
applicable) into worktop to secure it
in place.
Screws for attaching to worktop are not supplied as these
vary depending on worktop material and thickness. Ensure
appropriate xings for attaching worktop are used. Please
refer to the specialist worktop supplier if these are required
for solid surface worktops.
BASE UNIT
600 - 1000 Sink/Hob
1/2 Door
Assembly Guide
For Internal Use: FI.WR.INS.057_WKIN00145_BASE_600-1000_1-2Dr_Sink/Hob_Rev2.indd
Page 6
Step 12.
Insert hinge in top & bottom
holes as shown.
Step 13.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 14.
Attach the door to unit
where required.
To attach door
clip hinge onto hinge
plate and click to secure.
Step 16.
Fit cover caps to hinge.
Adjust Softclose to suit.
Step 15.
Adjust hinge to suit. As shown below.
To adjust hinge using a
screw driver,
tighten or loosen as
required at points 1 & 2.
Point 1 - In - Out
Point 2 - Left - Right
1
2
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from Inside of Carcass
To Release door
Pull catch as shown,
to release hinge
from the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
Hinge Cover Caps
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Wren Kitchens BASE UNIT 600 Assembly Manual

Wren Kitchens
Brand
Wren Kitchens
Model
BASE UNIT 600
Type
Assembly Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents