Page is loading ...
Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102am
SKU: STAND-V102AM
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF STAND
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
d1 (x1)
Monitor Arm
c (x1)
Decorative
Cover
a (x1)
48mm Pipe
e (x4)
Monitor Arm Cover
l (x1)
Support Plate
k (x1)
M10 Bolt
j (x2)
M8x10
i (x2)
M10x15
f (x4)
Plastic Pad
b1 (x1)
Clamp
g (x2)
M10x47
h (x3)
M6x10
p (x8)
Thumb Bolt
o (x1)
EVA Pad
n (x1)
Spring Washer
m (x1)
M10 Washer
s (x2)
Spare Cap
r (x8)
M4 Spacer
q (x8)
M4x30
t (x1)
Allen Key
w (x2)
Nut
v (x2)
VESA Plate
u (x1)
Wrench
x (x4)
Wire Clip
b2 (x1)
Clamp Brace
d2 (x2)
Monitor Arm
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
3
ASSEMBLY STEPS
STEP 1
OPTION 1: Clamp Installation
Install the C-clamp Brace (b2) to the 48mm Pipe
(a) using 3pcs C-clamp Brace Bolts (h). Install
the C-clamp (b1) to the 48mm Pipe (a) assembly
according to the thickness of the desktop.
Connect it using M10x15 Bolts (i), and tighten
using the Allen Key (t). Tighten the C-clamp to the
desktop using the eye bolts. Install the Decorative
Cover (c).
TOOLS NEEDED
Phillips
Screwdriver
OPTION 2: Existing Grommet Instllation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface before
installing the desk mount. Stick the EVA Pad (o) on
the round surface of 48mm Pipe (a). Position the
48mm Pipe (a) on the mounting surface and secure
using the Support Plate (l), M10 Washer (m), Spring
Washer (n) and M10 Bolt (k). Fasten the M10 Bolt
with provided Wrench (u). Install the Decorative
Cover (c).
OPTION 3: Self-Drilled Grommet Installation
Position the 48mm Pipe (a) on the mounting
surface and mark the center hole. Remove the
tube support. Drill a 3/8" (10mm) diameter hole
at the marked position through the mounting
surface. Stick the EVA Pad (o) on the round
surface of 48mm Pipe (a). Position the 48mm Pipe
(a) on the mounting surface and secure using the
Support Plate (l), M10 Washer (m), Spring Washer
(n) and M10 Bolt (k). Fasten the M10 Bolt with
provided Wrench (u). Install the Decorative Cover
(c).
Drill
a
h
b2
t
i
b1
eye bolt
c
o
a
c
a
l
k
m
n
o
a
c
a
l
k
m
n
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
4
STEP 2
Place plastic pads (f) onto ends of monitor arms (d2), insert into arms (d1), and secure using M10x47
bolts (g) with Allen wrench (t). Press monitor arm covers (e) onto joints.
STEP 3
Attach wire clips (x) to monitor arm (d1, d2). Install Monitor Arm to the 48mm Pipe (a), making sure
the wire clips are facing down. Fasten the arms using M8x10 Bolts (j) with Allen Key (t).
2.1
d2
d2
d1
e
e
g
t
f
2.2
2.3
t
a
d1,d2
x
j
5
w
STEP 4
OPTION B: Curved Back TV
Attach VESA Plates (v) to monitor using
screws (q) with M4 Spacers (r). Do not over-
tighten.
STEP 5
Slide the monitor onto the head of Swivel Arm (d2) as shown in the above diagram. Install the
security Nut (w). Make sure the security nut is installed before you rotate the monitor.
OPTION A: Flat Back TV
Attach VESA Plates (v) to monitor using screws (p).
Do not over-tighten.
p
v
r
q
v
6
STEP 6
STEP 7
Pry o the plastic cover and then use the Wrench (u) to tighten the nut if the tilt angle can not be fixed.
Remove the Nut (w) and turn the bolt counter-clockwise with supplied Allen key (t) to raise the monitor.
Reinstall the Nut aer the adjustment.
Pry o the arm cover, then use the Allen Key (t) to adjust the swivel joint tension.
Fix the tilt angle
u
t
t
7
STEP 8
Manage the wires.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/
