COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CUR-
RENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS
ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT
EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT
DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
ROUND HEAD FRAMING
NAILER KIT
MODEL G6050
INSTRUCTION MANUAL
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
NOTICE
Safety Instructions For Pneumatic Tools
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before operation.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use pneu-
matic tools in damp or wet loca-
tions, or where any flammable or
noxious fumes may exist. Keep
work area well lighted.
SAFETY
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
6. MAKE WORKSHOP CHILD
PROOF with padlocks, master
switches, or by removing air hoses
from tools.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a job
for which it was not designed.
9. DO NOT USE UNDER THE INFLU-
ENCE OF DRUGS OR ALCOHOL.
-1-G6050 Round Head Framing Nailer Kit
G6050 Round Head Framing Nailer Kit-2-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough to
reach your work without stretching.
11. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear a protective hair cov-
ering to contain long hair.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cut-
ting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
13. WEAR APPROVED HEARING
PROTECTION.
14. SECURE WORK. Use clamps or a
vise to hold work when practical. It is
safer than using your hand and frees
both hands to operate tool.
15. DO NOT OVERREACH. Keep prop-
er footing and balance at all times.
16. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean for
best and safest performance. Follow
instructions for lubricating and
changing accessories.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Do not carry
tool with hand on trigger and always
disconnect from air when not in use.
Safety Instructions For Pneumatic Tools
18. DISCONNECT TOOLS before ser-
vicing and changing accessories.
19. USE THE RECOMMENDED
ACCESSORIES. Consult the
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
20. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate prop-
erly and perform its intended func-
tion. Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
21. NEVER LEAVE UNATTENDED
TOOL CONNECTED TO AIR.
Disconnect the air hose and do not
leave tool until it is relieved of any
built up pressure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL
WHILE UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in pneumatic
tools.
G6050 Round Head Framing Nailer Kit
-3-
Operating this nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER whenever servicing or
installing nails. During maintenance,
a nailer connected to air may fire acci-
dentally, causing serious personal
injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nail can
deflect and be driven through the sur-
face of the workpiece, puncturing
your hand or fingers.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED OXYGEN OR
OTHER COMBUSTIBLE GASES as
a power source. Only use filtered,
lubricated, and regulated compressed
air.
5. ALWAYS KEEP ANY
BYSTANDERS BEHIND NAILER
OR AWAY FROM AREA DURING
USE. Nails may be driven completely
though wood and could become dan-
gerous projectiles.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING that allows air
to remain in the tool.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
G6050 Round Head Framing Nailer Kit-4-
INTRODUCTION
Commentary
Most important, we stand behind our tools.
If you have any service questions or parts
requests, please call or write us at the
location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Web Site: http://www.grizzly.com
We are proud to offer the Grizzly Model
G6050 Round Head Framing Nailer. This
model is part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoy-
able operation and proof of Grizzly’s com-
mitment to customer satisfaction.
The Model G6050 features a 360˚
adjustable exhaust, a quick release nose
clamp, a convenient side-loading maga-
zine, a safety trigger and a durable plastic
carrying case. The Model G6050 shoots
standard .113-.162 diameter shank round
head nails 2"-3
1
⁄2" in length and accepts
up to 50 nails at a time. At 7.5 lbs., this
model is very light for its size.
We are pleased to provide this manual
with the Model G6050. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. This manual
represents our effort to produce the best
documentation possible.
The specifications, details, and pho-
tographs in this manual represent the
Model G6050 as supplied when the man-
ual was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
C
/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
G6050 Round Head Framing Nailer Kit
-5-
Compressed Air System Safety Yoke Mechanism
The safety yoke is a mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
The Model G6050 is designed to be oper-
ated at 80-120 psi. Do not exceed the
maximum operating pressure!
Before you use your new nailer, regulate
the air pressure on your air compressor to
barely over the minimum psi for your nail-
er. Increase air pressure only if needed.
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. This
attachment is connected by hoses
between the air compressor and the nailer.
Using this unit protects your tool from dam-
aging water build-up, allows you to adjust
and maintain constant air pressure to your
tool, and saves you the inconvenience of
having to manually lubricate your tool
every time you use it. Check the current
Grizzly catalog for availability of this unit. If
you plan on installing a filter/lubricator/reg-
ulator unit in your compressed air system,
always follow the connection instructions
that come with the unit.
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a safety
device. When the trigger is pressed, the
nailer will not fire until the safety yoke
mechanism is depressed.
Before you use your nailer for the first time,
check the safety yoke mechanism to
ensure proper function. To do this:
1. Make sure the nailer is disconnect-
ed from the air supply!
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects. If the nailer
does not fire, then the safety yoke
mechanism is working correctly. If the
nailer does fire when you do this,
immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mech-
anism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
G6050 Round Head Framing Nailer Kit-6-
OPERATION
Loading Nailer
To load your nailer:
1. Disconnect the air supply from the
nailer!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Place a stick of nails into the maga-
zine as shown in Figure 1. Make sure
the pointed ends of the nails are fac-
ing down.
3. Slide the stick of nails all the way
down to the nose of the nailer.
4. Pull the magazine pusher all the way
back, release the catch pin, then let it
come forward until it rests against the
nail stick.
Figure 1. Loading the nailer.
Single/Bump Fire Mode
The Model G6050 is equipped with a sin-
gle/bump fire trigger.
To select single or bump fire operation:
1. Disconnect the air supply from the
nailer!
2. Locate the hex nut that secures the
safety yoke mechanism to the trigger
housing. See Figure 2.
3. To select Single Fire mode, tighten
the hex nut completely.
4. To select Bump Fire mode, unthread
the hex nut at least two full turns.
Figure 2. Single/bump fire adjustment.
Adjustment
Hex Nut
When replacing nails for your Model
G6050, follow these guidelines:
Diameter: .113" - .162"
Length: 2"-3
1
⁄2"
Capacity: 50 Nails
G6050 Round Head Framing Nailer Kit
-7-
Operating Nailer
Adjusting Depth
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
4. Press the trigger. If the nail drove into
the wood far enough, continue with
your intended operations. If the nail
either went too far or not far enough,
adjust the depth.
Figure 3. Example of nail deflection.
Figure 4. Depth adjustment slide located
on nailer nose guide.
If you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
Periodically, place one drop of the included
oil into the quick connect fitting where the
nailer connects to the air supply. After oil-
ing, wipe off any excess oil near the nailer
exhaust to avoid dust build-up.
To operate your nailer:
1. Connect the air supply to the quick
connect fitting.
2. Test the loaded nailer for proper pen-
etration. Hold the nailer perpendicular
to the surface of a piece of clean
scrap wood that is thick enough for
the length of nails you have loaded.
Depress the safety yoke mechanism
on your workpiece.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a nail
in case of deflection. (Deflection is
caused when the nail changes its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 3.)
The nose of the gun houses a cap screw
with a stepped slide plate (illustrated in
Figure 4) for setting the depth that the nail-
er drives nails into the workpiece.
Shallower
Deeper
G6050 Round Head Framing Nailer Kit-8-
Always disconnect air from nailer
whenever clearing a jammed nail!
Clearing Jammed Nails
The most frequent situation with any type
of nailer is a nail jam. A jammed nail must
be cleared before using the nailer again.
The two places where a nail can get
jammed are the magazine and the dis-
charge area.
To clear a jammed nail from the magazine:
1. Disconnect the nailer from the air
supply!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Locate and remove the jammed nail
with a pair of needle nose pliers.
Close the magazine cover so it latch-
es.
To clear a jammed nail from the discharge
area with the Model G6050:
1. Disconnect the nailer from the air
supply!
2. Pull the magazine pusher all the way
back until it locks in place.
3. Remove all nails from the magazine.
4. Locate the nail inside of the nailer
nose.
5. Find a tool that will fit inside the slot on
the underside of the nose and dis-
lodge the nail.
6. Throw the damaged nail away and
insert a new nail stick that only con-
tains clean, undamaged nails. DO
NOT use dirty or damaged nails in
your nailer!
G6050 Round Head Framing Nailer Kit
-9-
Cleaning Nailer
Use a good solvent to clean the nose
assembly of the nailer. Always be sure that
the nailer is dry before using it again.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air fittings.
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
Oiling Nailer
The Model G6050 is considered an oil-less
model. This means it features a teflon pis-
ton ring that does not require oil to operate.
However, periodic applications of oil will
extend the useful life of the piston assem-
bly.
Special oil has been included with you new
Grizzly Nailer. Periodically place one drop
of oil in the nailer air inlet (as shown in
Figure 6). After oiling, wipe off any excess
oil near the nailer exhaust to avoid dust
build-up. When the oil that was included
with the nailer has been completely used,
replace with Grizzly Model G2820
Pneumatic Tool Oil.
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit such
as the Grizzly Model H2333 in your air line.
Figure 6. Lubricating nailer via air inlet.
NOTICE
Too much oil in the nailer will ruin
the O-rings!
G6050 Round Head Framing Nailer Kit-10-
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out. To replace a
piston:
Figure 7. Removing nailer exhaust cap.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when
pushing the piston shaft with the
screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. Do not force the
piston into the cylinder! If the piston
is not easily inserted, double-check
the alignment of the piston shaft with
the grooves on the guide.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws from the
nailer exhaust cap.
4. Remove the exhaust cap as shown in
Figure 7.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
6. Open the magazine.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
G6050 Round Head Framing Nailer Kit
-11-
G6050 PART BREAKDOWN
25
1
2
1
4
1
3
11
1
0
9
8
59
26
6
5A
4
2A
7A
89
1A
24
30A
29
28A
82
80A
39
73
83A
74A
82
68A
28A
88
27
31A
35A
65
85
6
7
A
8
5
61A
66
3
9
92
90
39
23
22
19
2
1A
20
16B
15-2
15A
36
39
69
53A
52
51
50
49
48
47
46
45
42
43
44
41
37A
40
9
5
84
30A
71A
5656
6
2
63
64
21
-
1
12-1
58
60A
78
77
7
6
33
3
9
3
4
3
2
38A
57
G6050 -12-
01A P6048007A BUTTON HD CAP SCR
02A P6050002A EXHAUST COVER
04 P6050004 PU WASHER
05A P6050005A CAP SCREW + SW
06 P6050006 CAP
07A P6044077 FLAT WASHER
08 P6050008 SPACER
09 P6050009 PISTON STOPPER
10 P6050010 SPRING
11 P6050011 O-RING
12 P6050012 PISTON HEAD VALVE
12-1 P6050012-1 SPACER
13 P6050013 O-RING
14 P6050014 SEAL
15-2 P6050015-2 O-RING
15A P6050015A OIL-LESS RING ASSY
16B P6050016B PISTON ASSEMBLY
19 P6050019 O-RING
20 P6050020 O-RING
21A P6050021A CYLINDER
21-1 P6050021-1 O-RING
22 P6050022 UPPER BUMPER
23 P6050023 GASKET
24 P6050024 BODY
25 P6050025 BOTTOM BUMPER
26 P6050026 O-RING
27 P6050027 NOSE
28A P6050028A CAP SCREW
29A P6050029A STEPPED PIN
30A P6048030A PU RING
31A P6050031A BUTTON HD CAP SCR
32 P6050032 SAFETY LEVER
33 P6050033 SPRING
34 P6050034 SAFETY LEVER
35A P6050035A CAP SCREW
36 P6050036 SPRING
37A P6050037A SAFETY LEVER ASSY
38A P6050038A SPRING GUIDE
39 P6050039 LOCK NUT
40 P6050040 RUBBER PAD
41 P6050041 O-RING
42 P6050042 PLUNGER
43 P6050043 VALVE
44 P6050044 O-RING
45 P6048045 O-RING
46 P6050046 O-RING
47 P6044047 VALVE PLUNGER
48 P6050048 O-RING
49 P6048049 SPRING
50 P6050050 PLUNGER
51 P6050051 O-RING
52 P6050052 PLUNGER CAP
53 P6050053 TRIGGER ASSY
56 P6050056 PUSHER
57 P6050057 STOPPER
58 P6050058 SPRING
59 P6050059 GASKET
60A P6050060A SET PIN
61A P6050061A CAP SCREW
62 P6050062 SPIRAL SPRING
63 P6050063 ROLLER
64 P6050064 BALL PIN
65 P6050065 MAGAZINE
66 P6050066 NAIL GUIDE LINER
67A P6050067A CAP SCREW
68A P6050068A DEBRIS SHIELD
69 P6050069 FLAT WASHER
71A P6050071A INSERT
73 P6050073 BRACKET
74A P6050074A LOCK NUT
76 P6050076 SET PLATE
77 P6050077 SET PLATE
78 P6050078 BUTTON HD CAP SCR
80A P6050080A AIR PLUG
82 P6050082 FLAT WASHER
83A P6050083A GASKET WASHER
84 P6050084 STEPPED PIN
85 P6050085 SPACER
88 P6050088 SPRING WASHER
90 P6050090 BRACKET
92A P6044077 FLAT WASHER
93 P6050093 RUBBER PAD
REF PART # DESCRIPTION
REF PART # DESCRIPTION
TROUBLESHOOTING
Air leaking at trigger valve
area.
Air leaking between hous-
ing and hose.
Air leaking between hous-
ing and cap assembly.
Tool skips nails while dis-
charging.
Tool runs slowly or has a
loss of power.
Fasteners frequently jam
the nailer.
Nailer does not fire.
1. O-rings must be replaced
& operation of safety
yoke must be checked.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting.
1. Replace damaged seals.
1. Tighten screws and fit-
tings.
2. Clean nose.
3. Clean magazine and
inspect/repair damage.
4. Check fitting, hose, com-
pressor & air pressure.
5. Replace piston O-ring.
Lubricate.
6. Replace trigger valve O-
rings.
7. Replace bumper.
8. Replace cap seal.
1. Lubricate nailer.
2. Replace spring.
3. Clean or replace dam-
aged internal parts.
1. Use correct nails.
2. Use undamaged nails.
3. Tighten magazine and
nose screws.
4. Replace worn or dam-
aged parts.
5. Use correct angle nails.
1. Clear nailer magazine or
discharge area.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
PROBLEM
CAUSE
ACTION
-13-
1. O-rings in trigger valve
housing are damaged.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Damaged seal.
1. Air leaks.
2. Dirt in nose.
3. Dirt or damage prevents
nails from moving freely in
magazine.
4. Inadequate air flow to tool.
5. Worn O-ring on piston or
lack of lubrication.
6. Damaged O-rings on trigger
valve.
7. Worn bumper.
8. Cap seal leaking.
1. Nailer is not sufficiently lubri-
cated.
2. Broken spring in cap assem-
bly.
3. Exhaust port in cap is
blocked.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws
are loose.
4. Driver or driver guide are
worn or damaged.
5. Nails are wrong angle.
1. Nail is jammed in maga-
zine or discharge area.
2. Piston shaft is damaged.
3. Air pressure too low.
G6050 Round Head Framing Nailer Kit
G6050 Round Head Framing Nailer Kit-14-
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Web Site: http://www.grizzly.com
Thank you again for your business and continued support. We hope to serve you again
soon!
WARRANTY AND RETURNS
Name__________________________________________________________
Street__________________________________________________________
City____________________State________
Zip_________
Phone Number
____________
E-Mail___________________FAX____________
Model #_______________Serial#________________Order #______________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
WARRANTY CARD
9. How many of the machines checked above are
Grizzly? ____________
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander ___Orbital Sander
___Biscuit Joiner ___Palm Sander
___Circular Saw ___Portable Planer
___Detail Sander ___Saber Saw
___Drill/Driver ___Reciprocating Saw
___Miter Saw ___Router
___Other_________________________________
11. What machines/supplies would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
12. What new accessories would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
14. Do you think your purchase represents good value?
___Yes ___No
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___Yes ___No
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
1. How did you learn about us?
___Advertisement ___Friend
___Catalog ___Card Deck
___World Wide Web
___Other__________________________
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
3. What is your age group?
___20-29 ___50-59
___30-39 ___60-69
___40-49 ___70 +
4. How long have you been a woodworker?
___0 - 2 Years ___8 - 20 Years
___2 - 8 Years ___20+ Years
5. How would you rank your woodworking skills?
___Simple ___Advanced
___Intermediate ___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
___Air Compressor ___Panel Saw
___Band Saw ___Planer
___Drill Press ___Power Feeder
___Drum Sander ___Radial Arm Saw
___Dust Collector ___Shaper
___Spindle Sander ___Jointer
___Table Saw ___Lathe
___Mortiser ___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
7. How many of your woodworking machines are
Grizzly? _____________
8. Which benchtop tools do you own? Check all
that apply.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw ___8" - 10" Bandsaw
___Scroll Saw ___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
Name________________________________
Street________________________________
City______________State______Zip_______
Send a Grizzly Catalog to a friend:
Place
Stamp
Here
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
