Unika MP-2800 Owner's manual

Brand: Unika

Model: MP-2800

Type: Owner's manual

This manual is also suitable for

User Instructions

This booklet contains important information concerning the proper and safe operation of your new amplifier..

MP-Series

MP-2800 / MP-4000 / MP-5000

Made in Taiwan

Professional Power Amplif iers

Index

02 Introduction

03 Front Panel

04 Rear Panel

05 Set Up

07 Speakon Assembly

08 Operating Modes

12 Protection

13 Features

14 Specifications

UNiKA

STEREO

BRIDGE

PARALLEL

SIGNAL SIGNAL

CLIP CLIP

0 10 0 10

LIMITER LIMITER

POWER

OFF ON

CHANNEL 1 CHANNEL 2

ON ON

MP-2800

PROFESSIONAL AMPLIFIER

STEREO

BRIDGE

PARALLEL

SIGNAL SIGNAL

CLIP CLIP

0 10 0 10

LIMITER LIMITER

POWER

OFF ON

CHANNEL 1 CHANNEL 2

ON ON

MP-4000

PROFESSIONAL AMPLIFIER

STEREO

BRIDGE

PARALLEL

SIGNAL SIGNAL

CLIP CLIP

0 10 0 10

LIMITER LIMITER

POWER

OFF ON

CHANNEL 1 CHANNEL 2

ON ON

MP-5000

PROFESSIONAL AMPLIFIER

IMPORTANT SAFETY INSTRUCTIONS MP-2800/MP-4000/MP-5000

page 1

This symbol is intended to alert the user to the presence of

non insulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

CAUTION: Risk of the electrical shock - DO NOT OPEN!

CAUTION: To reduce the risk of electrical shock, do not remove cover. No user serviceable parts inside. Refer all servicing

to qualified service personnel.

WARNING: To prevent electrical shock or fire hazard, do not expose this amplifier to rain or moisture. Before using this

amplifier read the user manual for further warnings.

This symbol is intended to alert the user of

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

Este símbolo tiene el propósito de alertar al usuario de la

presencia de “voltaje peligroso” que no tiene aislamiento

dentro de la caja del producto que puede tener una

magnitud sufciente como para constituir riesgo de corrientazo.

PRECAUCIÓN: Riesgo del choque eléctrico - NO SE ABRA

PRECAUCIÓN: Para disminuir el riesgo de choque eléctrico, no quite la cubierta. No hay piezas adentro que el usario puede

reparar. Deje todo mantenimiento al los técnicos cualifcados.

ADVERTENCIA: Para prevenir choque eléctrico o riesgo de incendios, no deja expuesto a la lluvia o a la humedad este amplif

cador. Antes de usar este amplif cador, lea mas advertencias en la guia de operacion.

Este símbolo tiene el propósito de alertar al

usuario de la presencia de instrucciones

importantes sobre la operación y

mantenimiento en la literatura que vienc con el producto.

Ce symbole est utilisé pur indiquer à l’utilisateur la présence

à l'intérieur de ce produit de tension non-isolée

dangereuse pouvant être d'intensité suffisante pour

constituer un risque de choc électrique.

ATTENTION: Risque de choc électrique - NE PAS OUVRIR!

ATTENTION: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur aucune piéce

pouvant être réparée par l'utilisateur. Confier l'entretien à un personnel qualifé.

AVERTISSEMENT: Afin de prévenir les risque de décharge ou de feu, n’exposez pas cet appareil à la pluie ou à l’humidité.

Avant d’utiliser cet amplificateur, lisez les avertissements supplémentaries situés dans le guide.

Ce symbole est utilisé pour indiquer à l’utilisateur

qu'il trouvera d'importantes instructions

importantes sur l'utilisation et l'entretien de

l'appareil dans la littérature accompagnant le produit.

Dieses Symobl soll den Anwender vor unisollierten

gefährlichen Spannungen innerhalb des Gehäuses warnen,

die von Ausreichender Stärke sind, um einen elektrischen

Schlag verursachen zu können.

VORSICHT: Risiko - Elektrischer Schlag! Nicht öffnen!

VORSICHT: Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine

Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifzierte Fachpersonal

durchführen lassen.

ACHTUNG: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte diesen Gerät nicht dem Regen oder

Feuchtigkeit ausgesetz werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

Dieses Symobl soll den Benutzer auf wichtige

Instruktionen in der Bedienungsanleitung

aufmerksam machen, die Handhabung und

Wartung des Produkts betreffen.

CAUTION

Do not open -

risk of electric shock

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER. THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO

YOUR AUTHORIZED DEALER.

The lightning flash with an arrow triangular

symbol is intended to alert the user to the

presence of non insulated “dangerous

voltage” within the products enclosure, and

may be of sufficient magnitude to constitute

a risk of electric shock.

The exclamation point triangular symbol is

intended to alert the user to the presence of

important operating and maintenance

(servicing) instructions in the user manual

accompanying the amplifier.

FOR OPTIMUM PERFORMANCE AND RELIABILITY

DO NOT PRESENT THE AMPLIFIER WITH A

SPEAKER LOAD OF LESS THAN 2 OHMS OR ANY

COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS

THAN 2 OHMS!

USING ONE SPEAKER, IT MUST BE RATED AT 4 OR MORE

OHMS. USING TWO SPEAKERS, THEY MUST RATED EACH AT 4

OR MORE OHMS.

USING THREE SPEAKERS, THEY MUST BE RATED EACH AT 8

OR MORE OHMS.

POUR ASSURER LA FIABILETE ET OBTENIT UNE

PERFORMANCE OPTIMALE, NESOUMETTE

JAMAIS L’AMPLIFICATEUR A UNE CHARGE

D’IMPEDANCE

TOTALE INFERIEURE A 2 OHMS, NI AVEC UN H.P. N EN

COMBINAISON DES H.P.

AVEC UN H.P., IL FAUT UNE CHARGE D’IMPEDANCE MINIMUM

DE 2 OHMS.

AVEC DEUX H.P., FAUT POUR CHAOUN UNE CHARGE

D’IMPEDANCE MINIMUM DE 4 OHMS.

AVEC TROIS H.P., FAUT POUR CHAOUN UNE CHURGE

D’IMPEDANCE MINIMUM DE 8 OHMS.

page 2

IMPORTANT PRECAUTIONS

 To reduce the risk of electrical shock or fire, do not expose this unit rain or

moisture.

 Do not spill water or other liquids into or on to your unit.

 Do not attempt to operate this unit if the power cord has been frayed or

broken.

 Do not attempt to remove or break off the ground prong from the electrical

cord. This prong is used to reduce the risk of electrical shock and f re in

case of an internal short.

 Disconnect main power before making any type of connection.

 Do not remove the cover under any conditions. There are no user

serviceable parts inside.

 Never plug this unit in to a dimmer pack.

 Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

 Do not attempt to operate this unit, if it becomes damaged.

 This unit is intended for indoor use only, use of this product outdoors voids

all warranties.

 During long periods of non-use, disconnect the unit’s main power.

 Always mount this unit in a safe and stable manner.

 Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

 Cleaning -The outside of the unit should be wipe down with a soft cloth and

mild cleaner when needed.

 Heat -The amplifier should be situated away from heat sources such as

radiators, heat registers, stoves, or other appliances (including amplifiers)

that produce heat.

 The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a

marked change in performance.

Congratulations and thank you for purchasing MP-2800/MP-4000/MP-5000

amplifier. These amplifiers are representation of UNiKA’s continuing

commitment to produce the best and highest quality audio products at an

affordable price. These amplifiers are designed to provide a big impact in

sound reproduction. Please read and understand this manual completely

before attempting to operate your new amplifier. This booklet contains

important information concerning the proper and safe operation of your new

amplifier.

UNPACKING: Every MP-2800/MP-4000/MP-5000 amplifier has been

thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect your

unit for any damage and be sure all accessories necessary to operate the

system have arrived intact. In the event damage has been found or parts are

missing, please contact your dealer for further instructions.

INSTALLATION: These amplifiers are designed to mount into a

standard 19”rack. The front panel provides four holes used to screw the unit

into a rack. The unit also provides a way to rear mount the unit into a rack for

added security. Rear mounting the unit is especially recommended if the

unit is to mounted into a mobile rack.

INTRODUCTION

Introduction Front Panel Rear Panel Set Up Speakon Assembly Operating Modes Protection Features Specifications

UNiKA MP-2800/MP-4000/MP-5000

Introduction Rear Panel Set Up Speakon Assembly Operating Modes Protection Features SpecificationsFront Panel

MP-2800/4000/5000 FRONT PANEL

page 3

UNiKA MP-2800/MP-4000/MP-5000

Figure 1

STEREO

BRIDGE

PARALLEL

SIGNAL SIGNAL

CLIP CLIP

0 10 0 10

LIMITER LIMITER

POWER

OFF ON

CHANNEL 1 CHANNEL 2

ON ON

MP-5000

PROFESSIONAL AMPLIFIER

1 65432 97 8

1. Rack Mounting Ears - Two front panel mounting holes are provided on each

mounting ear.

2. AC Power Switch - MP Series amplifiers have a front-panel AC mains power

switch.

3. Mode Indicated LED - Red LED indicates "Parallel" Mode, Green LED

indicates "Stereo" Mode, Yellow indicates "Bridge" Mode.

4. UNiKA Logo and Model No - MP series have 3 types of 3U Models MP-2800

/ MP-4000 / MP-5000.

5. Fan Inlet Grills and Filter - MP Series amplifiers are cooled by two rear-

mounted fans. Cool air from front grills is filtered and flows over the heat sinks

and exhausts to back side. Make sure these outlets remain clear to allow

unrestricted air flow.

6. Limiter Switch - You can select limiter "ON" for limiter working, or turn "OFF”

the limiter.

7. Input Attenuators - Two input attenuators adjust level for their respective

amplifier channels.

8. Clip LED - Illuminates at the clipping threshold. Continuous illumination also

indicates that ACL (Active Clip Limiting) protection circuitry is engaged.

9. Signal LED - Illuminates to indicate that a signal (above a minimum threshold)

is present at the amplifier input, and that the signal is being amplified.

Introduction Front Panel Set Up Speakon Assembly Operating Modes Protection Features SpecificationsRear Panel

Figure 2

page 4

10. Fan Outlet Ports - Cooling air enters the amplifier through the front grills and

exhausts through the fans. Be sure not to block these ports when installing the

amplifier or other associated equipment. Air must flow unimpeded through these

ports.

11. Channel 2 Balanced 1/4" TRS & XLR Input Connectors - These connectors accept

input signals on balanced TRS and XLR input plugs. See the figures 3-5 for

information on polarity. Connectors for each channel are in parallel; the unused

connectors may be used for "loop through" connection to other amplifiers.

XLR pin setting: Pin-3/signal Negative, Pin-2/signal Positive, Pin-1/Ground.

12. Channel 2 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel

two on and off.

13. Channel 2 Frequency Adj. - This pot adjust the frequency level sent to your speaker

on channel two when using your amplifier in subwoofer mode.

14. Channel 1 Frequency Adj.- This pot adjust the frequency level sent to your speaker

on channel one when using your amplifier in subwoofer mode.

15. Channel 1 Subwoofer Mode On/Off Switch - Turns the subwoofer mode for channel

one on and off.

16. Channel 1 Balanced 1/4" TRS & XLR Input Connectors - These connectors accept

input signals on balanced TRS and XLR input plugs. See the figures 3-5 for

information on polarity. Connectors for each channel are in parallel; the unused

connectors may be used for "loop through" connection to other amplifiers.

XLR pin setting: Pin-3/signal Negative, Pin-2/signal Positive, Pin-1/Ground.

17. Channel 2 XLR THRU Jack - This Jack is used to send a parallel signal from the

channel 2 input jack to another device or amplifier.

18. Mode Selection Switch - This recessed, three-position switch configures the

amplifier for Stereo, Parallel or Bridged Mode operation. Amplifiers are factory-

configured for Stereo Mode. See section on Mode Selection for more information.

19. Channel 1 XLR THRU Jack - This Jack is used to send a parallel signal from the

channel 1 input jack to another device or amplifier.

20. Reset Button - This button is used to reset the breaker.

21. Channel 2 Speakon Output - Use pins 1+ and 1- of this 4-pole Speakon connector to

connect to your speakers input jack.

22. Channel 1 Speakon Output - Use pins 1+ and 1- of this 4-pole Speakon connector to

connect to your speakers input jack.

23. Channel 2 Output Jack / 5-Way Binding Post - Connect to your speakers input jack.

Red is positive signal and Black is negative signal.

24. Channel 1 Output Jack / 5-Way Binding Post - Connect to your speakers input jack.

Red is positive signal and Black is negative signal.

25. AC POWER Cord - Plug this cable into a standard 110V or 220V wall outlet. Be sure

that the supplied voltage in your area matches the amplifiers required voltage. Never

plug your amplifier into a wall outlet that does not match the required voltage of your

amplifier, serious damage may occur to your unit.

MP-5000 REAR PANEL

UNiKA MP-2800/MP-4000/MP-5000

242321

12 10

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

CH-1

CH-2

PINOU T

1+ 1-

POS NEG

CH- 2

PINOU T

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDG E

1+ 1 -

POS NEG

CH- 2

SUB

WOOF

CA U TION

MI NI MU M L OA D IM PE DAN CE

2 OH M PE R CH A NN EL

4 OH M BR ID G E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

11 16

Introduction Front Panel Rear Panel Speakon Assembly Operating Modes Protection Features SpecificationsSet Up

INPUTS - The MP-2800/MP-4000/MP-5000 amplifier allows you to use two types of input connectors per channel, a XLR female jack for

balanced connections and a 1/4” TRS female jack that will accept balanced and unbalanced connectors. Use these connections to connect the

output signal from a mixer, cross-over or EQ to your MP-2800/MP-4000/MP-5000 amplifiers. A balanced connection is recommended for cable

runs longer than 20ft. When constructing your own XLR cables follow the pin configuration described below for proper connections. For cable

runs shorter than 20ft., you may choose the 1/4” TS unbalanced input option. The 1/4” TS unbalanced input option may be more convenient for

most users due to the abundant supply of prefabricated cables available at your local audio dealer.You may use the two XLR “Input Thru” jacks

to jump a parallel connection to another amplifier or other device. For example: Connect a XLR cable to the input of channel one. You may now

connect a XLR cable from the channel one “Input Thru” jack to the input jack of another amplifier's channel one input. This will reduce the use of

“Y” cables.

OUTPUTS -

BINDING POST/BANANA PLUG: Connect your speakers to the binding post outputs on the rear of the amplifier. The

speaker wire may be connected by bare wire (directly connected, usually for permanent connections), banana plug, or

spade connector. Connections are made to channel one and channel two outputs for Stereo Mode or across the red

terminals of channel one and channel two for Mono Bridge Mode.

IMPORTANT NOTICE: Although a speaker will operate with the positive and negative leads plugged into either terminal

on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into the red

terminal. Ensuring proper polarity will avoid speakers being out of phase that can cause a loss of bass response.

Figure 6

2 Hot (+data)

Male XLR Pin Configuration

Figure 3

1 Ground / Return / 0v

3 Negative (-data)

Balanced TRS 1/4” Plug

Hot (+)

Negative (-)

Ground/Shield

Figure 4

Unbalanced TS 1/4” Plug

Hot (+)

Negative (-)

Figure 5

page 5

SET UP

UNiKA MP-2800/MP-4000/MP-5000

BANANA PLUG: (Figure 6)

When connecting your speakers to the amplifier using banana plug, be sure that the red and black caps on

the binding post are completely screwed in. Insert the banana plug into the caps of the binding post, be sure

that the banana plug is inserted securely to avoid the risk of popping out.

BARE WIRE CONNECTION: (Figure 7)

When connecting your speakers to the amplifier using bare wire, unscrew the red and black caps on the

binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire

insulation ½” (13mm). Insert the bare wire into the hole that was reveled by unscrewing the binding post cap.

After inserting the wire into the binding post hole, screw the binding post cap down on the wire. To reduce the

risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come

in contact with that of another.

SPADE CONNECTOR: (Figure 8)

When connecting your speakers to the amplifier using spade connector, unscrew the red and black caps on

the binding post, be sure not to completely remove or unscrew the red and black caps. Insert the spade

connector into the binding post and tighten the caps down on the spade connector. To reduce the risk of

shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in

contact with that of another.

MONO BRIDGE CONNECTIONS:

Mono bridge operation connections will follow the above descriptions, however, when operating in mono

bridge operation the speaker connections will run between the two positive (red) leads. Use channel two

positive output terminal for the speaker’s negative connection and the channel one positive output terminal

for the speaker’s positive connection.

Typical speaker output using bare wire.

Insert bare wire into the binding post and tighten.

Typical speaker output using spade connectors.

Insert bare wire into the binding post and tighten.

Figure 8

STEREO CONNECTIONS USING THE NEUTRIK SPEAKON OUTPUT CONNECTORS:

Recent regulatory requirements in Europe have outlawed the use of the dual banana plug and force amplifier users to terminate their speaker cables with spade lugs

or bare wire ends. This is not advantageous to most users that want to reconfigure their systems or quickly change out an amplifier. The Neutrik Speakon connector

provides the most convenient solution to this problem, eliminating the need for spade lugs or bare wire end cables. Major speaker manufacturers have been using

Speakon connectors on their products for years, so chances you are ready to use the Speakon connection. With Speakon connectors, you can connect straight from

the amplifier to the speaker. The Speakon connector used on this amplifier meets all known safety regulations. Once wired correctly, the connector cannot be plugged

in backwards, causing the type of inverted polarity situations that have become common with banana hookups. This connection will provide a safe, secure and

reliable method of connecting your speakers to your new amplifier. You can purchase the Speakon NL4FC connectors from your local audio dealer.

page 6

1/5"

13mm

Figure 7

UNiKA MP-2800/MP-4000/MP-5000

Introduction Front Panel Rear Panel Speakon Assembly Operating Modes Protection Features SpecificationsSet Up

page 7

Introduction Front Panel Rear Panel Set Up Operating Modes Protection Features SpecificationsSpeakon Assembly

You will need a pair of Neutrik Speakon NL4FC connectors. You will also need high-quality

two or four conductor Speakon cable, a pair of needle-nosed pliers and a 1.5-mm Allen key

to assemble the Speakon connectors to your speaker wire. To assemble the Neutrik

Speakon NL4FC connector, complete the following steps:

1. Strip back 3/4-inch of the cable casing. Strip off 1/4-inch from the end of each of the

conductors down to bare wire, and insert the brass fittings (Figure 9).

2. Slide the wire tensioner (D) and the Speakon coupler (E) through the cable end. See

Figure 10.

3. Insert each wire with the brass fittings into the top of appropriate slot of the connector

insert (B) as shown in Figure 11. Use a 1.5-mm Allen key to tighten the connection

(Figure 12).

4. Be sure to properly match the positive (+) and negative (-) leads of each wire (Figure 13).

5. Slide the connector insert (B) into the connector housing (A), making sure that the large

notch on the outer edge of the insert lines up with the large groove on the inside of the

connector housing. The insert should slide easily through the housing and out the other

side until it extends approximately 3/4-inch from the end of the housing.

6. Slide the cable tensioner (D) along the cable and insert into the housing (A), making sure

that the large notch lines up with the large groove on the inside of the connector housing

(A). The cable tensioner (D) should slide easily into the housing until only 3/8-inch of the

tensioner (D) extends from the back end of the connector.

7. Slide the coupler (E) along the cable and screw it onto the end of the housing (A). Before

tightening, you may want to test the connector to make sure it has been assembled

properly.

SPEAKON ASSEMBLY:

Figure 13

-1

-2

-1

-2

4-Conductor Speaker Cable

Brass Inserts

Figure 9

A EDCB

Figure 10

Figure 12

UNiKA MP-2800/MP-4000/MP-5000

Figure 11

INPUT BALANCE

OPERATING MODES

STEREO OPERATION : Page 8/ Figure 14 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier.

Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (fully counter-

clockwise). Turn your amplifier on. Turn your input source level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to

the clip level, however an intermittent clip signal is acceptable.

MONO BRIDGE OPERATION : Page 9/ Figure 15 details a mono bridge set-up. Be sure your amplifier and all other audio equipment are powered down.

Flip the Parallel/Stereo/Mono Bridge switch to the Mono Bridge position. Connect input signal to channel one. Connect your speaker across the red output

binding post on the rear of your amplifier. Turn your equipment on (your amplifier should always be the last item you turn on). Apply an input source signal to

your amplifier. Use the channel one gain to regulate your amplifier output.

PARALLEL MONO : Parallel ties the two channel line inputs together, so that they will both be driven by the same signal, without the need for external

jumpers or wiring. Both amplifier channels will operate independently. Though they carry the same signal, their gain controls affect only their respective

channels, and they both must use their respective speaker outputs. Never attempt to parallel the speaker outputs, this may cause serious damage to your

amplifier! This mode is recommended when using the MP-2800/MP-4000/MP-5000 to run bass speakers, to achieve better low end. To run in parallel mono

mode connect your system as you would if you were going to run in stereo mode. Then flip the mode switch to Parallel. Be sure the amplifier is off or the power

is disconnected before making any changes.

page 8

Introduction Front Panel Rear Panel Set Up Speakon Assembly Protection Features SpecificationsOperating Modes

UNiKA MP-2800/MP-4000/MP-5000

Figure 14 TYPICAL STEREO OUTPUT CONNECTIONS

SPEAKERS

2 OHM MINIMUM

SPEAKERS

2 OHM MINIMUM

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

CH-1

Input

PARALLEL

STEREO

BRIDGE

MP-5000 Rear Panel

CH-2

Input

MP-5000(110V)only

page 9

UNiKA MP-2800/MP-4000/MP-5000

SPEAKERS

4 OHM MINIMUM

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

CH-1 Input

PARALLEL

STEREO

BRIDGE

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

MP-2800 Rear Panel

Only

Figure 15 TYPICAL MONO BRIDGE SET-UP

PARALLEL

STEREO

BRIDGE

Either CH-1 or CH-2 input,

or Both inputs.

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

Figure 16 TYPICAL PARALLEL SET-UP

SPEAKERS

2 OHM MINIMUM

SPEAKERS

2 OHM MINIMUM

CH-1 Input

MP-2800

Rear Panel

CH-2 Input

Introduction Front Panel Rear Panel Set Up Speakon Assembly Protection Features SpecificationsOperating Modes

Do Not Use

CH-2 Input

CH-1 Input

Set to

Subwoof

Negative (-) Lead

Positive (+) Lead

PARALLEL

STEREO

BRIDGE

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

MP-2800 Rear Panel

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

SUBWOOFER MODE : This mode sends low frequencies to your speakers without the use of an external cross-over. The subwoofer operation can be operated in

stereo, parallel, or bridge modes. Change the different operating modes by flipping the mode switch on the rear of the unit to your desired operating mode. Also, set the

subwoofer mode switch to the ”SUBWOOF” position. Use the frequency selector to adjust the subwoofer output frequency from 20Hz to 200Hz. The different subwoofer

modes are listed as follows:

BRIDGE SUBWOOFER - This operation allows you to get the most possible power out of your amplifier for the sole purpose of running a high powered subwoofer

loudspeaker in mono. To avoid amplifier overheating, never run the amplifier below 4 ohms in this mode. In this mode you may use the frequency adjustment on the rear

of the amplifier, to control the frequency output level. Frequencies may be adjusted from 20Hz to 200Hz. Page 10 / 17 details a typical Bridge Subwoofer set-up.Figure

STEREO SUBWOOFER - This operation is similar to the Bridge Subwoofer operation but in stereo. This operation allows you to run several subwoofers down to a

minimum of 2 ohms. To avoid amplifier overheating, never run the amplifier below 2 ohms in this mode. Set up this mode as you would a standard Stereo set-up. Be sure

both channels are set to “SUBWOOF.” In this mode you may use the frequency adjustment on the rear of the amplifier, to control the bass frequency output level.

Frequencies may be adjusted from 20Hz to 200Hz. Page 11 / 18 details a typical Stereo Subwoofer set-up.Figure

PARALLEL SUBWOOFER - This operation is similar to the Stereo Subwoofer operation but in parallel. When running subwoofers, it is usually recommended to run

them in mono mode to achieve a cleaner tighter low end. This operation allows you to run several subwoofers down to a minimum of 2 ohms. To avoid amplifier

overheating, never run the amplifier below 2 ohms in this mode. Set up this mode as you would a standard Stereo set-up. Be sure both channels are set to “SUBWOOF”

and the mode switch is set to “Parallel.” In this mode you may use the frequency adjustment on the rear of the amplifier, to control the bass frequency output level.

Frequencies may be adjusted from 20Hz to 200Hz.

ONE CHANNEL NORMAL / ONE CHANNEL SUBWOOFER (BI-AMP) - You may also use your amplifier to bi-amp your system. You may use one side of the amplifier

to power a subwoofer and the other side to power a full range speaker. Follow the set up guides listed above to mix and match your operations.

page 10

UNiKA MP-2800/MP-4000/MP-5000

Bridge Subwoofer Mode Speaker Set-Up

Figure 17

Use the two red terminal from the Binding Post to

power a subwoofer speaker in mono-bridge mode.

Introduction Front Panel Rear Panel Set Up Speakon Assembly Protection Features SpecificationsOperating Modes

PARALLEL

STEREO

BRIDGE

Either CH-1 or CH-2 input,

or Both inputs.

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

CH-1 Input

MP-2800

Rear Panel

CH-2 Input

Set to

Subwoof

Set to

Subwoof

page 11

UNiKA MP-2800/MP-4000/MP-5000

Figure Parallel Subwoofer Mode Speaker Set-Up 19

Use either the bare wire

or the banana jacks

Use either the bare wire

or the banana jacks

Figure Stereo Subwoofer Mode Speaker Set-Up 18

Use either the bare wire

or the banana jacks

Use either the bare wire

or the banana jacks

PARALLEL

STEREO

BRIDGE

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

PARALLEL

STEREO

BRIDGE

NORMAL

FREQUENCY

NORMAL

SUB

WOOF

FREQUENCY

CH-1

20 Hz20 Hz 200 Hz200 Hz

CH-2

INPUT BALANCE INPUT THRU

CH-1

CH-2

PUSH TO RESET

HOT

COLD

GND

BRIDGE

MONO

+ +

CH-1

CH-2

PINOUT

1+ 1-

POS NEG

CH- 2

PINOUT

2+ 2-

POS NEG

CH- 2

1+ 2+

POS NEG

BRIDGE

1+ 1-

POS NEG

CH- 2

SUB

WOOF

CA UTIO N

MI NI MUM L OA D IM PE DA NC E

2 OH M PE R CHA NN EL

4 OH M BR IDG E

Made in Taiwan

S/N.:

~120V 60 Hz

4200 WATTS

CH-1 Input

MP-2800 Rear Panel

CH-2 Input

Set to

Subwoof

Set to

Subwoof

Introduction Front Panel Rear Panel Set Up Speakon Assembly Protection Features SpecificationsOperating Modes

PROTECTION

LIMITER - The MP-2800/MP-4000/MP-5000 amplifiers comes with a built in limiter. When the input signal overloads, the “CLIP LED” indicates a signal overload, at this

time, the volume should be lowered to reduce distortion. If the input gain level is not reduced the built-in limiter will activate. During signal overload, the limiter will reduce

the input audio signal enough to minimize the amount of clipping. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion

that can cause damage to your speakers and amplifier. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio

signal and is inaudible. It will allow brief clipping of peaks and will only activate when continuous hard clipping occurs. During excessive clipping the limiter will reduce

the audio signal enough to minimize the amount of clipping. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain

reduction. The limiter has a fixed threshold and can not be adjusted.

SAFE POWER LEVELS AT DIFFERENT OUTPUT LOADS:

8-Ohm Loads : The amplifier can operate at its rated power level without risk of overheating. However, it may caused excessive temperature if it is pushed hard enough

to continually light the “CLIP” indicator, the amplifier’s average output power can reach its maximum peak.

4-Ohm Loads : If the “CLIP” indicator flashes occasionally, the amplifier is approaching its Maximum long-term power capacity. If it is lit about half the time, the amplifier

channel will probably go into thermal protection within a few minutes.

2-Ohm Loads : Except for an occasional flash, keep the “CLIP” indicator dark to avoid overheating the amplifier channel. Clipping should be kept to a reasonable

minimum. An amplifier’s peak current draw at full output power into 2 ohms is several times what the “normal ” draw is, but its various protection circuits will prevent this

condition lasting more than a minute or two.

page 12

SHORT CIRCUIT PROTECTION - The MP-2800/MP-4000/MP-5000 amplifiers comes with built-in Output Short Circuit Protects.

The Output Short Circuit Protection protects the output devices of the amplifier from short circuits and stressful loads. If your speaker

lines shorted, the amplifier automatically detects this problem and discontinued operation for that channel. If one side of your amplifier

becomes shorted and goes into protect mode, the other side will continue to operate normally. Channel output during the “Short Circuit

Protection" will be interrupted (i.e. no sound output). Short Circuit Protection can usually be traced back to the signal output line (i.e.

speaker line). Check the line from the output terminal of the amplifier to the speaker. If this line is good, check the internal speaker

connections and components. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to

the amplifier itself.

Introduction Front Panel Rear Panel Set Up Speakon Assembly Operating Modes Features SpecificationsProtection

UNiKA MP-2800/MP-4000/MP-5000

THERMAL PROTECTION - Dual 2-speed fans on the MP-2800/MP-4000/MP-5000 amplifiers provide adequate cooling. During low level output the fans

run at normal speeds. During high output and as heat raises, (exceeding 50°C.), the fans will run at higher speeds to aid the cooling process. If the heatsink

temperature exceeds 91°C., the amplifier will mute until the amplifier cools down. When the amplifier cools below 90°C., the amplifier will return to normal

operations. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems.

INPUT/OUTPUT PROTECTION - The input circuits are isolated by resistors. An ultrasonic network uncouples RF from the output and helps to keep the

amplifier stable with reactive loads.

OPERATING VOLTAGE (AC MAINS) - On the rear panel will indicate the correct AC mains voltage. Connecting to the wrong voltage is dangerous and

may damage the amplifier. Always be sure the source voltage for your areas matches the required voltage for your amplifier.

GAIN CONTROLS - The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. It is best to a d j ust the

amplifier so no “hissing” is heard from speakers with no music being played, this will ensure the lowest possible distortion d u ring normal operation.

AMPLIFIER FEATURES:

THRU - THRU will allow the user to daisy-chain one amplifier’s signal input into another amplifier. Plug the signal source outputs into the first amplifier’s input,

patch from the amplifier’s THRU jacks to the next amplifier’s input, and so on, daisy-chaining as many amplifiers as there is no excessive level loss.

LED INDICATORS - Each channel has one red LED indicates signal clipping and one green LED indicates input signal is present.

FUNCTION INDICATORS - These green/red/yellow LED indicators detail the amplifiers current operating mode (Stereo, Parallel, or Bridge).

page 13

UNiKA MP-2800/MP-4000/MP-5000

Introduction Front Panel Rear Panel Set Up Speakon Assembly Operating Modes SpecificationsProtection Features