Barska BI12308 Owner's manual

Barska
Brand
Barska
Model
BI12308
Type
Owner's manual

This manual is also suitable for

The Barska BI12308 is a versatile spotting scope that is perfect for nature enthusiasts, bird watchers, and target shooters. With its 20-60x magnification, you can get a close-up view of distant objects, while the large 80mm objective lens gathers plenty of light for bright, clear images, even in low-light conditions. The spotting scope also features a durable, waterproof construction, so you can use it in any weather. The Barska BI12308 comes with a tripod for stable viewing, and a carrying case for easy transport and storage.

The Barska BI12308 is a versatile spotting scope that is perfect for nature enthusiasts, bird watchers, and target shooters. With its 20-60x magnification, you can get a close-up view of distant objects, while the large 80mm objective lens gathers plenty of light for bright, clear images, even in low-light conditions. The spotting scope also features a durable, waterproof construction, so you can use it in any weather. The Barska BI12308 comes with a tripod for stable viewing, and a carrying case for easy transport and storage.

Locate the quick-release pull cord
Tab on the front panel of the VX-300.
Release it from the Velcro Retainer by
pulling the securing ap back.
Next, pull the entire length of the quick-
release cord out of the VX-300 vest.
This will release all of the individual vest
sections.
Separate the individual vest
sections. These include the Front
and Back Section, Small and Large
Cummerbunds.
Insert the Small Cummerbund into the
Back Vest Section. Make sure that the
soft Velcro side is facing upwards.
While inserting the small cummerbund
into the back section, be sure to feed it
through the internal waist loop. Feed the
grommet strap through until it appears in
the rear access port.
Thread the paracord loop through the
desired grommet on the cummerbund
strap. Note: For a tighter t, feed the
paracord loop through a grommet that is
further in on the cummerbund strap.
Actual color may vary.
Register your product easily online at
www.LoadedGear.com
www.loadedgear.com
8/16 BC482
Parts Of The Vest
A - Front Section
B - Back Section
C - Two Small Cummerbunds
D - Two Large Cummerbunds
1 2 3
4 5 6
VX-300 Tactical Vest Assembly
TM
A
B
C D
Repeat Steps 4-6 for the opposite side
small cummerbund.
Locate the Large Cummerbund and feed
it through the vest’s back section.
Feed the large cummerbund OVER the
internal belt loop that is securing the
small cummerbund. Pull the grommet
strap through to the rear access port.
Thread the paracord loop through the
desired grommet on the cummerbund
strap. Note: For a tighter t, feed the
paracord loop through a grommet that is
further in on the cummerbund strap.
Repeat Steps 8-10 for the opposite side
large cummerbund.
Locate the Quick-Release Pull Cord and
the VX-300 Front Section.
Reattach the Quick-Release Pull Cord
to the Velcro Retainer on the Front Vest
Section.
Secure the Quick-Release Pull Cord by
covering it with the Velcro ap.
Feed the Quick-Release Pull Cord
through the Pull Cord Channel Located
on the right shoulder strap.
VX-300 Tactical Vest Assembly
TM
www.loadedgear.com
7 8 9
10 11 12
13 14 15
2
Continue feeding the Quick-Release Pull
Cord through the Pull Cord Channel until
the cord appears out of the other end
of the channel near the shoulder strap
grommets.
Feed the non-wired shoulder strap
through the shoulder strap sleeve on
the rear section of the vest. Be sure
to continue feeding the shoulder strap
down into the body of the vest.
Reach up into the back section of the
vest and pull the shoulder strap down so
that it is visible in the rear access port.
Feed the paracord loop through the
desired grommet on the shoulder strap.
Note: the further up you thread the
paracord, the higher the vest will sit on
your body.
Feed the shoulder strap with the pull
cord through the shoulder strap sleeve
on the rear section of the vest.
Feed the shoulder strap and pull cord
down into the body of the vest until it
appears in the rear access port.
Feed the paracord loop through the
shoulder strap. Make sure to use the
same grommet placement as the other
shoulder strap to maintain an even
adjustment.
Run the pull cord cable through
the paracord loop to secure each
cummerbund into place. Tuck the
remaining pull cord length into the vest.
Waist and shoulder adjustments on the
VX-300 are complete. Close the rear
access port and fasten the button on the
cover strap.
VX-300 Tactical Vest Assembly
TM
www.loadedgear.com
16 17 18
19 20 21
22 23 24
3
The VX-300 Vest is now assembled. To get in or out of the vest,
simply lift up the Velcro Sections from Step 25 and detach the
cummerbund from the Velcro section.
www.loadedgear.com
Flip the vest over so that the Front Vest
Section is on top. Open the large Velcro
sections on the left and right side of the
vest.
Fold the cummerbunds over and attach
them to the large Velcro section. Repeat
this process for the opposite side.
Close the top Velcro section to secure
the cummerbunds into place.
VX-300 Tactical Vest Assembly
TM
25 26 27
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Barska BI12308 Owner's manual

Barska
Brand
Barska
Model
BI12308
Type
Owner's manual
This manual is also suitable for

The Barska BI12308 is a versatile spotting scope that is perfect for nature enthusiasts, bird watchers, and target shooters. With its 20-60x magnification, you can get a close-up view of distant objects, while the large 80mm objective lens gathers plenty of light for bright, clear images, even in low-light conditions. The spotting scope also features a durable, waterproof construction, so you can use it in any weather. The Barska BI12308 comes with a tripod for stable viewing, and a carrying case for easy transport and storage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents