DELTA DORE TYXAL+ CLE 8000 Installation guide

DELTA DORE
Brand
DELTA DORE
Model
TYXAL+ CLE 8000
Type
Installation guide

DELTA DORE TYXAL+ CLE 8000 is an outdoor keypad that can be associated with a DELTA DORE X3D wireless alarm system and/or an X3D control system receiver. With this device you can control your alarm system or control systems, create 4-digit access codes, and it's IP 64 rated making it weatherproof. The average range is 20m, which will be optimised if the device is mounted at height. Installation is easy with the provided screws. The device uses a Lithium battery - AA LS 14500 3,6 V which has a 10 year life.

DELTA DORE TYXAL+ CLE 8000 is an outdoor keypad that can be associated with a DELTA DORE X3D wireless alarm system and/or an X3D control system receiver. With this device you can control your alarm system or control systems, create 4-digit access codes, and it's IP 64 rated making it weatherproof. The average range is 20m, which will be optimised if the device is mounted at height. Installation is easy with the provided screws. The device uses a Lithium battery - AA LS 14500 3,6 V which has a 10 year life.

EN
Smoke detector
www.deltadore.com
LS14500 – 3,6V - Lithium
Consumption stand-by : 2.5 µA
Consumption : 25 mA max..
868 - 868.6 MHz / 868.7 - 869.2 MHz
100 m Ý 300m
Maximum power radio < 10 mW,
receiver category: 2
-10°C / +70°C
-25°C / +70°C
IP
IP 64
75%
77 x 112 x 27 mm
Important product
information (Ë Ì)
313 gr.
Contenu / Contents / Inhalt /
Contenuto / Contenido / Inhoud /
Zawartość
Instructions
Important
Product
Informations
CLE 8000 TYXAL +
* Up to 10 years valid under the conditions of use specied in the
installation instructions and the General Conditions of Sale
Instructions
Important
Product
Informations
EN
- 2 -
- 3 -
1. Presentation
2. Location
CLE 8000 TYXAL+ is an outdoor keypad that can be associated with a
DELTA DORE X3D wireless alarm system and/or an X3D control system
receiver.
Before using your keypad, if you want to:
A) Control the alarm, you must associate the keypad with the alarm system:
Read system installation guide
B) Control the control systems:
Ê Select the operating mode:
, , or
Ë Associate the control system receivers.
Ì Create the 4-digit access codes to be able to control them.
Ê Separate the 2 parts of the unit. Ë Glue the seal to the rear panel of
the base.
3. Mounting
1
3
4
C
V2
V1
D2
D1
1
2
3
2
1
3
4
C
V2
V1
D2
D1
1
2
3
2
The radio range between the CLE 8000 TYXAL+ (outdoors) and the CS
8000 TYXAL+ (indoors), or the control system receiver, depends on the
environment and installation conditions.
The installation mounting can affect the radio range. The keypad must not be
mounted on a metal surface, otherwise the range will be affected.
The average range is 20 m. It will be optimised if the device is mounted at
height (e.g. 1.50 m from the fl oor).
1
2
Lithium battery - AA
LS 14500 3,6 V
3
4
1
2
3. Mounting
Ì Mark and drill holes D1, D2. Ì Mount the base using screws V1,
V2.
1
3
4
C
V2
V1
D2
D1
1
2
3
2
1
3
4
C
V2
V1
D2
D1
1
2
3
2
Ø max = 3 mm
4. Activation
Ê Fit the battery, observ-
ing the right polarity.
Ë Close and lock the unit.
Lithium battery - AA
LS 14500 3,6 V
1
• Association with an alarm system
• Selection of triggering method
• Test
Read system installation
guide
5. Operation with an alarm system
EN
- 4 -
- 5 -
6. Customise the and buttons.
There are 3 modes: D, E and F.
Pulse control of a control
system or one lighting group
Channel 1 Channel 2
ON / OFF
Roller shutter control
Raise Lower
ON / OFF
Control of several lighting
groups
On Off
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
6. Customise the and buttons for a control
system receiver
Ê Press and hold the
button for 5
seconds.
The LED (
button)
is green, switches
off then flashes to
indicate the operating
mode.
Ë Press the
button, then
select the required operating
mode by briefly pressing
the button as many times as
1
2
... ... ...
...
... ...
... ... ...
> 5s
Mode F
Mode E
Mode D
3
> 5s
necessary:
- 1 flash (
... ... ...
...
... ...
... ... ...
)
= D mode (e.g. gate)
- 2 flashes (
... ... ...
...
... ...
... ... ...
)
= E mode (roller shutter)
- 3 flashes (
... ... ...
...
... ...
... ... ...
)
= F mode (e.g. lighting)
Ì To confirm and
exit the mode,
press the
button, for 5
seconds.
EN
- 6 -
- 7 -
7. Associate the and buttons for 1 control system
receiver
3
OK
1
2
>5s
or
>3s
OFF
OFF
>5s
>5s
Example Example
Ê Set the receiver
to association
wait mode
(refer to guide).
Ë On the keypad, press the
button for 5 seconds. The
keypad emits a beep.
The LED (
button) is
green, switches off then
flashes to indicate the oper-
ating mode.
Press the button to associate
(
or , refer to detail
below) for 5 seconds, the
keypad emits a 2nd beep.
Release.
Ì Check that the
receiver has
acknowledged the
request
(refer to the guide).
On the keypad, the
LED flashes red
(
button) then
green.
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
Press then for channel 1.
Press
then for channel 2.
Press
then or
Ë
Detail:
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
8. Configure the alarm and control system access codes
Ê Enter your access code (1234 by default)
Ë On the keypad, press the
button for 5 seconds.
The red LED (
button) will come on.
Ì Enter the new access code (4 digits), then press
.
The green LED comes on for 3 seconds, then red.
To confi rm and exit the mode, press the
button, for
5 seconds.
Alarm access code:
Control system access code:
• Upon activation, the user code is
,
• To change the default access code or create
a new access code:
The CLE 8000 TYXAL+ uses 2 types of access code:
You can create up to 9 different control system access codes.
Beyond this input is refused and the keypad emits aseries of
beeps.
• To create, modify or delete an access code
(installer or user),refer to the system installation
guide.
EN
- 8 -
- 9 -
9. Operation
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
or
or
Example
Press the button for channel 1 or for channel 2.
The LED (
button) changes from red to green.
Press the button to raise the
roller shutter.
Press the button to lower the
roller shutter.
During the raising or lowering
operation, pressing
stops the
roller shutter. (Do not enter the 4-digit
access code).
Enter your 4-digit code, then:
Enter your 4-digit code, then:
Press the button to switch on. Press the button to switch off.
or
The LED ( button) changes from red to green.
Tryb E
Tryb F
Tryb D
Modo E
Modo F
Modo D
Modalità E
Modalità F
Modalità D
Modus E
Modus F
Modus D
Mode E
Mode F
Mode D
On
Off
On
Off
or
Enter your 4-digit code, then:
The LED (
button) changes from red to green.
10. Remove the association with a control system receiver
and the control system access codes
1
2
3
4
5
>10s
1 2
Ë Separate the product from
its base unit.
Ë Press the button located inside the
keypad for 10 seconds.
The keypad emits a beep when
pressed, then a second beep after 10
seconds. Release.
11. Battery replacement
1
2
3
4
Lithium battery - AA
LS 14500 3,6 V
The LED fl ashes red ( button) whenever it is pressed. The battery is dead.
Before opening the unit, the alarm control unit must be in Maintenance
mode (refer to system installation guide).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

DELTA DORE TYXAL+ CLE 8000 Installation guide

DELTA DORE
Brand
DELTA DORE
Model
TYXAL+ CLE 8000
Type
Installation guide

DELTA DORE TYXAL+ CLE 8000 is an outdoor keypad that can be associated with a DELTA DORE X3D wireless alarm system and/or an X3D control system receiver. With this device you can control your alarm system or control systems, create 4-digit access codes, and it's IP 64 rated making it weatherproof. The average range is 20m, which will be optimised if the device is mounted at height. Installation is easy with the provided screws. The device uses a Lithium battery - AA LS 14500 3,6 V which has a 10 year life.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents