Brother QL-1050N User manual

Label Overview

STEP

1

Introduction

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference

Installing the Software

Setup & Operation Guide

Guía de configuración y uso

Be sure to read and understand this guide before using the machine. We

recommend that you keep this guide nearby for future reference.

Asegúrese de leer este manual antes de usar la impresora. Le recomendamos

conservar este manual a mano para poder consultarlo como referencia en el futuro.

Thank you for purchasing the Brother QL-1060N.

This guide briefly describes the steps to start using the Brother QL-1060N.

See the User's Guide for details. The User's Guide can be found in the Manuals folder of

the included CD-ROM.

We strongly recommend that you read this guide carefully before using the Brother

QL-1060N, and then keep it nearby for future reference.

We provide service & support for users who register their products on our website.

We recommend that you take this opportunity to register with us by visiting us at:

Online User Registration

http://registermybrother.com/

Online Support Page

http://solutions.brother.com/

NOTE: It is also possible to access the above sites from the online user registration

window of the included CD-ROM. We look forward to your registration.

Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)

Responsible Party: Brother International Corporation

100 Somerset Corporate Boulevard

Bridgewater, NJ 08807-0911 USA

TEL: (908) 704-1700

declares that the product

Product Name: Label Printer QL-1060N

Model Number: QL-1060

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Important

The enclosed interface cable should be used in order to ensure compliance with the limits for a

Class B digital device.

A shielded interface cable should be used in order to ensure compliance with the limits for a Class

B digital device.

Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user's

authority to operate the equipment.

Brother

®

Two-Year Limited Warranty and Replacement Service

(USA Only)

Who is covered:

• This limited warranty ("warranty") is given only to the original end-use/retail purchaser

(referred to in this warranty as "Original Purchaser") of the accompanying product,

consumables and accessories (collectively referred to in this warranty as "this Product").

• If you purchased a product from someone other than an authorized Brother reseller in

the United States or if the product was used (including but not limited to floor models or

refurbished product), prior to your purchase you are not the Original Purchaser and the

product that you purchased is not covered by this warranty.

What is covered:

• This Product includes a Machine and Consumable and Accessory Items. Consumable

and Accessory Items include but are not limited to label and tape rolls and print servers.

• Except as otherwise provided herein, Brother warrants that the Machine and the

accompanying Consumable and Accessory Items will be free from defects in materials

and workmanship, when used under normal conditions.

• This warranty applies only to products purchased and used in the United States. For

products purchased in, but used outside, the United States, this warranty covers only

warranty service within the United States (and does not include shipping outside the

United States).

What is the length of the Warranty Periods:

• Machines: two year from the original purchase date.

• Accompanying Consumable and Accessory Items: 90 days from the original purchase

date or the rated life of consumable, whichever comes first.

What is NOT covered:

This warranty does not cover:

(1) Physical damage to this Product;

(2) Damage caused by improper installation, improper or abnormal use, misuse, neglect or

accident (including but not limited to transporting this Product without the proper

preparation and/or packaging);

(3) Damage caused by another device or software used with this Product (including but not

limited to damage resulting from use of non Brother

®

-brand parts and Consumable and

Accessory Items);

(4) Consumable and Accessory Items that expired in accordance with a rated life; and,

(5) Problems arising from other than defects in materials or workmanship.

This limited warranty is VOID if this Product has been altered or modified in any way

(including but not limited to attempted warranty repair without authorization from Brother

and/or alteration/removal of the serial number).

What to do if you think your Product is eligible for warranty service:

Report your issue to our P-touch Customer Service Hotline at 1-877-BROTHER (1-877-

276-8437) or to a Brother Authorized Service Center within the applicable warranty

period. Supply Brother or the Brother Authorized Service Center with a copy of your

dated bill of sale showing that this Product was purchased within the U.S.. For the name

of local Brother Authorized Service Center(s), call 1-877-BROTHER (1-877-276-8437) or

visit www.brother-usa.com.

What Brother will ask you to do:

After contacting Brother or a Brother Authorized Service Center, you may be required to

deliver (by hand if you prefer) or send the Product properly packaged, freight prepaid, to

the Authorized Service Center together with a photocopy of your bill of sale.

You are responsible for the cost of shipping, packing product, and insurance (if you desire).

You are also responsible for loss or damage to this Product in shipping.

INTRODUCTION

What Brother will do:

If the problem reported concerning your Machine and/or accompanying Consumable and

Accessory Items is covered by this warranty and if you first reported the problem to

Brother or an Authorized Service Center within the applicable warranty period, Brother or

its Authorized Service Center will repair or replace the Machine and/or accompanying

Consumable and Accessory Items at no charge to you for parts or labor. The decision as

to whether to repair or replace the Machine and/or accompanying Consumable and

Accessory Items is made by Brother in its sole discretion.

Brother reserves the right to supply a refurbished or remanufactured replacement

Machine and/or accompanying Consumable and Accessory Items and use refurbished

parts provided such replacement products conform to the manufacturer's specifications

for new product/parts.

The repaired or replacement Machine and/or accompanying Consumable and Accessory

Items will be returned to you freight prepaid or made available for you to pick up at a

conveniently located Authorized Service Center.

If the Machine and/or accompanying Consumable and Accessory Items are not covered

by this warranty (either stage), you will be charged for shipping the Machine and/or

accompanying Consumable and Accessory Items back to you and charged for any

service and/or replacement parts/products at Brother's then current published rates.

The foregoing are your sole (i.e., only) and exclusive remedies under this warranty.

What happens when Brother elects to replace your Machine:

When a replacement Machine is authorized by Brother, and you have delivered the

Machine to an Authorized Service Center, the Authorized Service Center will provide you

with a replacement Machine after receiving one from Brother. If you are dealing directly

with Brother, Brother will send to you a replacement Machine with the understanding that

you will, after receipt of the replacement Machine, supply the required proof of purchase

information, together with the Machine that Brother agreed to replace. You are then

expected to pack the Machine that Brother agreed to replace in the package from the

replacement Machine and return it to Brother using the prepaid freight bill supplied by

Brother in accordance with the instructions provided by Brother. Since you will be in

possession of two machines, Brother will require that you provide a valid major credit

card number.

Brother will issue a hold against the credit card account number that you provide until

Brother receives your original Product and determines that your original Product is

entitled to warranty coverage. Your credit card will be charged up to the cost of a new

Product only if: (i) you do not return your original Product to Brother within five (5)

business days; (ii) the problems with your original Product are not covered by the limited

warranty; (iii) the proper packaging instructions are not followed and has caused damage

to the product; or (iv) the warranty period on your original Product has expired or has not

been sufficiently validated with a copy of the proof of purchase (bill of sale).

The replacement Machine you receive (even if refurbished or remanufactured) will be

covered by the balance of the limited warranty period remaining on the original Product,

plus an additional thirty (30) days. You will keep the replacement Machine that is sent to

you and your original Machine shall become the property of Brother.

Retain your original

Accessory Items and a copy of the return freight bill, signed by the courier.

Limitations:

Brother is not responsible for damage to or loss of any equipment, media, programs or

data related to the use of this Product. Except for that repair or replacement as described

above, Brother shall not be liable for any direct, indirect, incidental or consequential

damages or specific relief. Because some states do not allow the exclusion or limitation

of consequential or incidental damages, the above limitation may not apply to you.

THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR

ORAL, WHETHER EXPRESSED BY AFFIRMATION, PROMISE, DESCRIPTION,

DRAWING, MODEL OR SAMPLE. ANY AND ALL WARRANTIES OTHER THAN THIS

ONE, WHETHER EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED.

• This Limited Warranty is the only warranty that Brother is giving for this Product. It is the

final expression and the exclusive and only statement of Brother's obligations to you. It

replaces all other agreements and understandings that you may have with Brother or its

representatives.

• This warranty gives you certain rights and you may also have other rights that may vary

from state to state.

• This Limited Warranty (and Brother's obligation to you) may not be changed in any way

unless you and Brother sign the same piece of paper in which we (1) refer to this Product

and your bill of sale date, (2) describe the change to this warranty and (3) agree to make

that change.

Important:

We recommend that you keep all original packing materials, in the event that you ship

this Product.

Should you have questions, or need information about your Brother Product, we have a

variety of support options for you to choose from:

USA-Customer Service:

Customer Service

1-877-BROTHER (1-877-276-8437)

Customer Service

1-901-379-1210 (fax)

Website

www.brother-usa.com

Supplies / Accessories

www.brothermall.com

or 877-552-6255

BROTHER INTERNATIONAL CORPORATION

100 SOMERSET CORPORATE BLVD.

BRIDGEWATER, NEW JERSEY 08807-0911

Record your model and serial number and your date and location of Purchase below for

your records. Keep this information with your proof of purchase (bill of sale) in case your

Product requires service.

Model # __________________________________________

Serial # __________________________________________

Date of purchase: __________________________________

Store where purchased: _____________________________

Location of store: __________________________________

Important: We recommend that you keep all original packing materials, in the event that

you need to ship the machine.

Save Time - Register On-Line!

Don’t stand in line at the post office or worry about lost mail. Visit us on-line at

www.registermybrother.com

Your product will immediately be registered in our database and you can be on your way!

Also, while you're there, look for contests and other exciting information!

Important Information

Page is loading ...

Introduction

2

Compilation and Publication Notice

Under the supervision of Brother Industries Ltd., this guide has been compiled and

published, covering the latest product’s descriptions and specifications.

The contents of this guide and the specifications of this product are subject to

change without notice.

Brother reserves the right to make changes without notice in the specifications and

materials contained herein and shall not be responsible for any damages (including

consequential) caused by reliance on the materials presented, including but not limited to

typographical and other errors relating to the publication.

The screen images in this guide can be differed depending on your OS or printer.

Trademarks

The Brother logo is a registered trademark of Brother Industries, Ltd.

Brother is a registered trademark of Brother Industries, Ltd.

Microsoft, Windows Vista and Windows are either registered trademarks or trademarks

of Microsoft Corp. in the United States and/or other countries.

Apple, Macintosh and Mac OS are trademarks of Apple Inc., registered in the United

States and other countries.

The names of other software or products used in this document are trademarks or

registered trademarks of the respective companies that developed them.

Each company whose software title is mentioned in this guide has a Software License

Agreement specific to its proprietary programs.

All other brand and product names mentioned in this Setup & Operation Guide and the

User's Guide are registered trademarks of their respective companies.

Symbols Used in this Guide

The symbols used throughout this guide are as follows:

This symbol shows information or directions that should be followed. If ignored, the

result may be injury, damage, or failed operations.

This symbol shows information or directions that can help you better understand and

use the machine more efficiently.

General Information

3

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Introduction

Getting started

Reference Installing the Software

Label Overview

Read and understand all of these instructions and save them for later reference. Follow

all warnings and instructions marked on the product.

The symbols used in this guide are as follows:

To use the machine safely

Warning Tells you what to do to avoid the risk of injury.

Caution

Tells you about procedures you must follow to prevent damage to the machine.

Action NOT allowed to do DO NOT disassemble the product.

DO NOT splash the product with or

immerse the product in water.

DO NOT touch a given portion of the

product.

Mandatory action Unplugging

Alerts to the possibility of electrical

shock

Warning

Follow these guidelines to avoid fire, electric shock, or other damage.

The Machine

Unplug the power cord immediately and

stop using the machine during an

electrical storm. There may be a remote

risk of electric shock from lightning.

Do not touch any metal parts near the

print head. The print head becomes very

hot during use and remains very hot

immediately after use. Do not touch it

directly with your hands.

Dispose of plastic bags correctly and

keep away from babies and children. Do

not wear or play with plastic bags.

Unplug the power cord immediately and

stop using the

machine

if you notice any

abnormal odor, heat, discoloration,

deformation or anything unusual whilst the

machine

is in use or storage.

Do not disassemble the machine.

For inspection, adjustment and repair of

the machine contact the retail outlet

where the machine was purchased or

your local authorized service center.

Do not drop, hit or otherwise bang the

machine.

Do not hold and lift the machine by the

DK Roll cover. The cover could come off

and the machine could fall and become

damaged.

Do not allow the

machine

to get wet in any

way.

Do not use the machine with foreign

objects in it. If water or any foreign

objects should enter the machine,

unplug the power cord from the electric

outlet and remove the foreign object. If

necessary, contact the retail outlet

where the machine was purchased or

your local authorized service center.

Do not hold the machine with only one

hand. The machine may slip out of your

hand.

Safety Precautions

Introduction

4

Follow these guidelines to avoid fire, electric shock, or other damage.

Power Cord

Use only the authorized power source

(120V AC) for the machine.

Use only the power cord included with

the machine.

Do not handle the power cord or plug if

your hands are wet.

Do not overload the electrical outlet

sockets with too many appliances or

plug the power cord into a damaged

electrical outlet.

Do not cut, damage, alter or place heavy

objects on the power cord.

Do not use the power cord if it is

damaged.

Ensure the power cord is correctly

inserted into the electrical outlet.

If the machine will not be used for an

extended period, remove the power cord

from the electrical outlet.

Caution

Follow these guidelines to avoid fire, electric shock, or other damage.

The Machine

The electrical outlet should be close to the machine and be easily accessible.

Power Cord

Always hold the power cord when unplugging the power cord from or plugging it into

the electrical outlet. Pulling on the power cord could cause problems.

Cutter

Do not touch the blade of the cutter.

Do not open the top cover when the cutter is operating.

Installation/Storage

Put the machine on a flat, stable surface

such as a desk.

Do not put any heavy objects on top of

the machine.

DK Roll (DK Label, DK Tape)

Be careful not to drop the DK Roll.

DK Rolls use thermal paper and thermal

film. Both the label and print will fade

with sunlight and heat. Do not use DK

Rolls for outdoor use that requires

durability.

Depending on the area, material, and

environmental conditions, the label may

unpeel or become irremovable, the color

of the label may change or be

transferred to other objects.

Before applying the label, check the

environmental condition and the

material. Test the label by affixing a

small piece of it to an inconspicuous

area of the intended surface.

Warning

5

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Introduction

Getting started

Reference Installing the Software

Label Overview

The Machine

• Never disassemble the machine or allow it to get wet to avoid possible fire or electrical

shock. Do not unplug the power cord from or plug it into the electrical outlet with wet

hands. Doing so could cause an electrical shock or fire.

• Do not touch the cutter. Personal injury could result.

• The machine is a precision machine. Do not drop, hit or otherwise bang the machine.

• Do not lift the machine by the DK Roll compartment cover. The cover could come off and

the machine could fall and become damaged.

• The machine may malfunction if left near a television, radio, etc. Do not use the machine

near any machine that can cause electromagnetic interference.

• Do not expose the machine to direct sunlight or near heaters or other hot appliances, in

any area exposed to extremely high or low temperatures, high humidity or dusty areas.

Doing so could cause the machine to malfunction.

• Do not use paint thinner, benzene, alcohol or any other organic solvents to clean the

machine. Doing so may cause damage to the surface finish. Use a soft, dry cloth to clean

the machine.

• Do not put any heavy objects or objects containing water on top of the machine. If water

or any foreign object enters the machine, contact the retail outlet where the machine was

purchased or your local authorized service center. If you continue to use the machine

with water or a foreign object in the machine, the machine may be damaged or personal

injury could result.

• Do not insert any objects into or block the label output slot, USB port, Serial port or LAN

port.

• Do not put any metal parts near the print head. The print head becomes very hot during

use and remains very hot immediately after use. Do not touch it directly with your hands.

• Use only the interface cable (USB cable) included with the machine.

• When not in use for an extended period, remove the DK Roll from the machine.

• Do not attempt to print labels while the DK Roll cover is open.

Power Cord

• Use only the power cord included with the machine.

• If the machine will not be used for an extended period, unplug the power cord from the

electrical outlet.

• Always hold the power cord when unplugging the power cord from or plugging it into

electrical outlet. Do not pull on the power cord. The wire in the electrical cord may

become damaged.

• You should put the machine near an easily accessible, standard electrical socket.

DK Roll (DK Label and DK Tape)

• Use only genuine Brother accessories and supplies (with , marks). Do not use any

unauthorized accessories or supplies.

• If the label is attached to a wet, dirty, or oily surface, it may peel off easily. Before

applying the label, clean the surface to which the label will be applied.

• DK Roll uses thermal paper and thermal film so that ultraviolet rays, wind, and rain may

cause the color of the label to fade and the ends of the label to peel off.

• Do not expose the DK Rolls to direct sunlight, high temperatures, high humidity, or dust.

Store in a cool, dark place. Use the DK Rolls soon after opening the package.

• Scratching the printed surface of the label with your finger nails or metal objects, or

touching the printed surface with hands dampened by water, sweat, or medicated cream,

etc., can cause the color to change or fade.

• Do not apply labels to any persons, animals, or plants.

General Precautions

Introduction

6

• As the end of the DK Roll is designed to not adhere to the label spool, the last label may

not be cut properly. If this happens, remove the remaining labels, insert a new DK Roll,

and reprint the last label.

Note: To account for this, the number of DK Labels included on each DK Roll may be

more than indicated on the package.

• If a label is removed after begin applied to a surface, some portion of the label may

remain. Remove the remaining portion before attaching a new label.

• Some DK Rolls use permanent adhesive for their labels. These labels cannot be easily

peeled off once attached.

• Prior to using CD/DVD labels, be sure to follow the instructions in your CD/DVD player's

instruction guide regarding applying CD/DVD labels.

• Do not use CD/DVD labels in a slot loading CD/DVD player, for example a CD player in

a car where the CD is slid into a slot in the CD player.

• Do not peel off the CD/DVD label once it is applied to the CD/DVD, a thin surface layer

may come off, resulting in damage to the disk.

• Do not apply CD/DVD labels to CD/DVD disks designed for use with ink jet printers.

Labels peel off these disks easily and using disks with peeled labels can result in loss or

damage of data.

• When applying CD/DVD labels, use the applicator included with the CD/DVD label rolls.

failure to do so could cause damage to the CD/DVD player.

• User's shall take full responsibility for applying CD/DVD labels. Brother accepts no

responsibility for any loss or damage of data caused by the inappropriate use of CD/DVD

labels.

CD-ROM and Software

• Do not scratch or subject the CD-ROM to high or low temperatures.

• Do not put heavy objects on the CD-ROM or apply force to the CD-ROM.

• The software contained on the CD-ROM is meant for use with the machine only. See the

License on the CD for details. This software may be installed on multiple computers for

use in an office, etc.

7

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference Installing the Software

Label Overview

Introduction

Getting started

Check that the package contains the following before using the QL-1060N. If any item is

missing or damaged, contact your Brother dealer.

QL-1060N

USB cable SETUP & OPERATION GUIDE

CD-ROM DK Label & Tape Guide

AC Power cord

DK Roll (Starter roll)

The QL-1060N includes two starter rolls of :

• One starter roll of DK Die-cut

4" X 6" (102mm × 152mm) Labels

• One starter roll of DK Continuous Paper Tape

2-3/7" (62mm)

Warranty Card

Label tray

1 Unpacking the QL-1060N

STEP1 Getting started

8

Front Rear

1

Press and hold the ON/OFF button to turn

the QL-1060N off. Pull up the left and right

levers on the machine under the top cover,

and open the cover.

2

Put the spool into the spool guides in the DK

Roll compartment.

• Make sure that the spool arms are inserted firmly in

the spool guides on the left and right.

• Insert the spool with the DK Roll located on the right

hand side of the QL-1060N.

2 Parts Description

Main Printing Unit

FEED button

LED lamp

ON/OFF button

CUT button

DK Roll compartment cover

Power cord

USB port

LAN port

Serial port

3 Setting the DK Roll

9

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference Installing the Software

Label Overview

Introduction

Connect the power cord to the

QL-1060N and then plug the power

cord into a electrical outlet.

• Check that the electrical outlet is 120V

AC before plugging the power cord.

• Unplug the power cord from the

electrical outlet after you have finished

using the QL-1060N.

• Do not pull the power cord when

unplugging it from the electrical outlet.

The wire in the power cord may

become damaged.

• Do not connect the QL-1060N to the

computer until directed to do so when

installing the printer driver.

3

Thread the end of the DK Roll into

the slot until it can be seen from the

other side.

When unable to thread the end of the

DK Roll into the slot, thread it as far as

possible, and then close the cover.

Press the ON/OFF button to turn the

QL-1060N on, and then press the

FEED button to set the roll.

4

Close the DK Roll compartment cover until it

clicks right and left side.

4 Connecting the Power Supply

STEP1 Getting started

10

The machine contains a label tray

which can hold up to 10 individual

label sheets.

As shown right, install the label tray

to the front face of the machine.

• When printing more than 10 labels

continuously using the auto cut

function, remove the paper guide to

prevent a paper jam.

RS-232C cable and Network cable are not standard accessories.

Prepare the appropriate cable for your interface.

• USB cable

Use the enclosed interface cable.

• RS-232C cable

Do not use an interface cable that is longer than 6 feet (2.0 meters).

For details, see Appendix-Serial Cables of User’s Guide.

• Network cable

Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or

100BASE-TX Fast Ethernet Network.

Important

The enclosed interface cable should be used in order to ensure

compliance with the limits for EMC.

A shielded interface cable should be used in order to ensure compliance

with the limits for EMC.

Changes or modifications not expressly approved by Brother Industries,

Ltd. could void the user's authority to operate the equipment.

• Caution for LAN connection

Connect this product to a LAN connection that is not subjected to overvoltages.

• Caution for RS-232C connection

The RS-232C serial connector part of this equipment is not Limited Power Source.

5 Installing the Label Tray

6 Using Interface Cable

11

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference Installing the Software

Label Overview

Introduction

Installing the Software

This section explains how to install the P-touch Editor 5.0, P-touch Address Book 1.1,

Printer Driver, and User's Guide as a whole.

The procedure for installing them varies depending on the OS of the computer.

The following is the example for Windows Vista

®

.

Install procedure is subject to change without notice.

1

Start the computer and put the CD-ROM into the CD-ROM drive.

If it does not start up automatically, open the files on the CD-ROM and double

click on "Setup.exe".

2

Click "Standard Installation".

Installation items:

Standard Installation

P-touch Editor 5.0,

P-touch Address Book 1.1,

Printer Driver, User's Guide (PDF),

and Network User's Guide (PDF)

Custom Installation

P-touch Editor 5.0, P-touch

Address Book 1.1, Printer Driver,

User's Guide (PDF), and Network

User's Guide (PDF)

Utility Installation

BRAdmin Light

User's Guide

User's Guide (PDF), Network User's Guide (PDF), and link to the download

page for Adobe

®

Reader

®

.

3

Read the license agreement and click [Yes] if you agree with the

terms and conditions.

4

Follow the on-screen instructions.

Installing the Software

1.

When using Microsoft

®

Windows

1

2

3

4

1

2

3

4

STEP2 Installing the Software

12

5

Put a check mark in the box to install the

Add-in and click [Next].

Make sure that you closed all Microsoft

®

Office

®

applications.

For details on the Add-in, see the "User's

Guide (PDF)".

6

Click [OK].

Then, choose your connection method and click [Next].

For USB interface cable users

7-1

Choose Local Printer with USB cable

and click [Next].

7-2

Follow the on-screen instructions. When

this screen appears, make sure to turn

on the power. Connect the USB interface

cable to your computer, and then

connect it to the machine.

Now, go to step 8 on page 14.

13

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference Installing the Software

Label Overview

Introduction

For Network interface cable users

For shared network printer users

7-1

Choose Brother Peer-to-Peer Network

Printer, and then click [Next].

Check that LAN cable and the machine are

connected.

7-2

Choose Search the network for devices

and choose from a list of discovered

devices (Recommended). Or enter your

machine’s IP address or its node name.

Click [Next].

You can find your printer's IP address and the

node name by printing out the Printer Settings

Page, please refer to the NETWORK USER'S

GUIDE for details.

7-3

Choose your printer.

Now, go to step 8 on page 14.

7-1

Choose Network Shared Printer, and

then click [Next].

Check that LAN cable and the machine are

connected.

STEP2 Installing the Software

14

For details on software, see Î"User's Guide (PDF)".

You can find the User's Guide (PDF) by clicking [Start]-[ALL Programs (Programs)]-

[Brother P-Touch]-[Manuals]-[QL-1060N User's Guide (English)].

7-2

Choose your printer's queue, and then

click [OK].

Contact your administrator if you do not know

the location or the name of the printer in the

network

8

Click [Next].

• If you choose "Yes, display the page", you will go to the online user registration

page before finishing the installation. (recommended)

• If you choose "No, do not display the page", you will continue the installation.

9

Click [Finish].

10

Start the software.

• Click [Start] - [All Programs (Programs)] - [Brother P-touch] - [P-touch Editor 5.0]

to start P-touch Editor.

• Click [Start] - [All Programs (Programs)] - [Brother P-touch] - [P-touch Address

Book 1.1] to start P-touch Address Book.

15

STEP

1

STEP

2

STEP

3

For Windows

®

For Macintosh

®

STEP

4

Getting started

Reference Installing the Software

Label Overview

Introduction

Installing the BRAdmin Light configuration utility for Windows

The BRAdmin Light is a utility for initial setup of Brother network connected devices. It

can also search for Brother products on your network, view the status and configure

basic network settings, such as IP address.

For more information on BRAdmin Light, visit us at http://solutions.brother.com.

Setting your IP address, Subnet Mask and Gateway using

BRAdmin Light

• If you require more advanced printer management, use the latest Brother BRAdmin

Professional utility version that is available as a download from

http://solutions.brother.com.

• If you are using Personal Firewall software, BRAdmin Light may fail to detect the

unconfigured device. In that case, disable your Personal Firewall software, try

BRAdmin Light again. Re-start your Personal Firewall software after the address

information is set.

1

Click Utility Installation.

This screen is the same screen as you

see when you insert the CD-ROM.

2

Click BRAdmin Light and follow the on-

screen instructions.

If the Windows Firewall is enabled on your PC,

the message “Do you wish to add this application

to the list of exceptions?” appears. Check your

PC environment and choose Yes or No.

1

Start BRAdmin Light. It will search for new

devices automatically.

If you have a DHCP/BOOTP/RARP server in your

network, you don’t have to do the following

operation. Because the print server will

automatically obtain its IP address.

Page is loading ...

Brother QL-1050N User manual

Brother QL-1050N User manual

in other languages

Related papers

Other documents