Vetus CWS is a water strainer with a transparent lid, making it possible to check if the filter needs cleaning without the need to open it. The large active surface of the filter means it rarely requires cleaning. Its standard capacity, as per the data provided, can be increased by connecting two water filters with two extra valves in parallel. This also means that each filter can be cleaned separately while the engine is running.
Vetus CWS is a water strainer with a transparent lid, making it possible to check if the filter needs cleaning without the need to open it. The large active surface of the filter means it rarely requires cleaning. Its standard capacity, as per the data provided, can be increased by connecting two water filters with two extra valves in parallel. This also means that each filter can be cleaned separately while the engine is running.
Koelwaterfilter
Cooling water strainer
Kühlwasserfilter
Filtre à eau froide
Filtro de agua de enfriamiento
Filtro per acqua di raffreddamento
Installatie instructies 2
Installation manual 4
Einbauanleitung 6
Instructions d’installation 8
Instrucciones de instalación 10
Istruzioni per l’installazione 12
Copyright © 2017 Vetus b.v. Schiedam Holland
CWS
Page is loading ...
Page is loading ...
4 030507.01
Cooling water strainer model CWS
Introduction
The Vetus cooling water strainers model CWS
are equipped with a transparant lid, inspection
therefore, can be carried out without opening
of the strainer.
Due to the large active surface the strainer sel-
dom needs to be cleaned.
In a standard installation situation (see ‘Instal-
lation examples’, drawing 1 and 2) the capacity
is as per technical data.
Parallel connection
By connection of 2 water strainers in parallel
with the use of 2 extra valves (see ‘Installation
example, drawing 3) it is possible to clean each
lter separately while the engine is running.
Installation
• Install the water strainer always above the
waterline.
• Use brackets to mount the strainer against a
vertical bulkhead.
• Install always a sea-cock on the water inlet
scoop!
• Install the water strainer with the inlet di-
rectly to a stand-pipe, see drawing 1, or con-
nect the inlet by means of hose pillar and a
exible hose, see drawing 2.
• Use a teon tape as sealant for the connec-
tions.
• To connect the strainer to the engine always
a hose pillar and a exible hose should be
used.
• Use only water and/or soap to ease tting
the hoses to the hose pillars and never prod-
ucts containing grease or oil.
• Fit each hose connection with 2 stainless
steel hose clamps.
Use and maintenance
• Inspect the strainer element regularly for
contaminents.
N.B. The lid doesn’t need to be removed for
inspection.
• Clean the strainer element if dirt has accu-
mulated. Close the seacock and open the
lid:
Remove the bolt (A), loosen the other bolt
(B) and open the clamp, see g. 2.
Remove the strainer element out of the
housing and ush the strainer with clean
water.
• Re-install the strainer element, grease the
O-ring and the thread with e.g. silicone oil
or teon based spray, see drwg 6, and rein-
stall the lid.
030507.01 5
Cooling water strainer model CWS
Model Hose connection
Recommended capacity
in normal use
l/min Imp.Gal/min US Gal/min
CWS 1 G 1 91 20 24
CWS 1
1
/
4
G 1
1
/
4
143 31 38
CWS 1
1
/
2
G 1
1
/
2
200 44 53
Check the seal between lid and housing after
cleaning and re-assembling the strainer. An
improperly sealed lid will result in air sucked
in by the sea water pump of the engine which
again will result in overheating of the engine.
To prevent damage of the water strainer, dur-
ing frost in the winter time, either the water
must be drained or the installation must be
lled with anti-freeze.
Remove the hoses to drain the strainer; the
housing is not equipped with a drain plug.
Take care that during lling with anti-freeze
no anti-freeze is spilled into the waterway.
Anti-freeze is poisonous.
Technical data
Material
- housing : Polypropylene GF
- strainer element : HD Polyethylene
- lid : Styrol/Acrylnitrile SAN
Weight : 6.2 kg (13,7 lb)
Max. ambient temp. : 75 °C (167°F)
Max. water temp. : 55 °C (131°F)
Max. pressure : 7.5 bar
(750 kPa,
109 psi
)
ENGLISH
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
14 030507.01
Cooling water strainer model CWS
183 (7
3
/
16
”)
ø
135 (5
5
/
16
”)
190
(7
1
/
2
”)
130
(5
1
/
8
”)
204
(8
1
/
16
”)
ø
O.D.
ø
O.D.
Hoofdafmetingen
Overall dimensions
Hauptmaße
Dimensions pricipales
Dimensions generales
Misure pricipali
030507.01 15
Cooling water strainer model CWS
Installatievoorbeelden
Installation examples
Installationsbeispiele
Exemples d’installation
Ejemplos de instalación
Esempi di installazione
WL
min. 15 cm
(6”)
1
16 030507.01
Cooling water strainer model CWS
WL
min. 15 cm
(6”)
2
WL
min. 15 cm
(6”)
3
030507.01 17
Cooling water strainer model CWS
A
B
A
B
1 2 3
4 5 6
7
Reinigen Cleaning Reinigung Nettoyage Limpieza Pulizia
PTFE GREASE
18 030507.01
Cooling water strainer model CWS
1
CWS Service onderdelen Service parts
pos. qty part benaming description
1 1 CWSCSET Set: afdekplaat, rubber
element en O-ring.
Set: cover plate, Element
rubber and O-ring.
030507.01 19
Cooling water strainer model CWS
vetus b.v.
FOKKERSTRAAT 571 - 3125 BD SCHIEDAM - HOLLAND
TEL.: +31 0(0)88 4884700
[email protected] - www.vetus.com
Printed in the Netherlands
030507.01 2017-08
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Vetus CWS is a water strainer with a transparent lid, making it possible to check if the filter needs cleaning without the need to open it. The large active surface of the filter means it rarely requires cleaning. Its standard capacity, as per the data provided, can be increased by connecting two water filters with two extra valves in parallel. This also means that each filter can be cleaned separately while the engine is running.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Vetus CWS Guida d'installazione
- français: Vetus CWS Guide d'installation
- español: Vetus CWS Guía de instalación
- Deutsch: Vetus CWS Installationsanleitung
- Nederlands: Vetus CWS Installatie gids
Related papers
-
Vetus Cooling Water Strainer 330/330M Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Toast 135.114 Datasheet
-
Trane UNT-SVU008-XX-0906 User manual
-
Wayne CWS75 Operating instructions
-
Bard Davol CWS 400 User manual
-
-
Frigoboat FRIGOMATIC 35F - 50F Operating And Maintenance Instructions Manual
-
-
Danfoss FIA Strainer Installation guide
-
-
